|
|
| Products 151 to 180 of 361 |
|
|
|
|
The Advance Optima process gas analyzers have a modular design that increases flexibility and saves money.
Analyzer modules can be combined into tailor-made solutions and upgraded to new features at any time.
Remote modules are easily attached and centrally operated.
One central unit and various analyzer modules
- with common controls
- with a common connection technology
- in a common system housing
All analyzers use high performance measurement technology and simplified calibration that doesn't require test gas bottles.
- Photometers
- In-Situ Laser Analyzer
- Oxygen Analyzers
- Trace Oxygen Analyzer ZO23
- Thermal Conductivity Analyzers
- FID Analyzers
read more...
The AO2000 analyzers provides Ethernet, TCP/IP interfaces. An OPC server is available. Profibus DP/PA and Modbus interfaces are available.
AO2000 system components are available with GOST-R certificates as with CSA approval for Class I Division 2 and ATEX approval for installation in Zone 1 or Zone 2.
For measuring flammable gases in hazardous locations the AO2000 series provides a safety concept with built-in purge control and alarm monitoring.
|
|
|
|
|
|
Gasmonitor Plus is just one of Crowcon’s control panel range. This flexible, rack based, microprocessor-controlled unit is used throughout the world, both onshore and offshore. Gasmonitor Plus provides the cost-effective solution to your system requirements.
Features:
Simple to Use
• All the day to day functions are available from the front panel
• The unique bar graph display per channel provides an instant representation of gas concentrations
• Common alarm LEDs on the display card mean that the whole rack status can be checked at a glance.
Flexible Architecture
• System is limitlessly expandable
• System customisation is achievable with minimal wiring
• Designed to industrial standards, Gasmonitor Plus will integrate fully with existing rack mounted protection systems on site
• Optional relay modules can be used to provide up to a total of 84 output relays per rack.
• Sixteen of these relays can be voted to activate from a combination of the three levels of alarm per channel
Other controllers in our fixed gas monitoring range include:
Vortex 1 to 12 channel control system
Gasmaster 1 to 4 channel control system
Gasflag Single channel control system
CellarSafe CO2 monitoring system
Ditech modular gas and fire detection and extinguishant control system
|
|
REGARD is a state-of-the-art microprocessor-driven, modular gas monitoring system.
Each card is fully configurable for all types of transmitters and gases, using the on-board push buttons. The gas concentration is displayed on a LED display and status LED’s allow a quick overview on the condition of the system.
|
|
|
MSA offers a complete range of safety related modular control systems, for all system sizes and applications, designed to process the input signals of gas detectors and other devices. In alarm conditions appropriate actions are triggered by the controller.
|
|
|
|
|
|
BW Technologies by Honeywell announces the arrival of the latest portable multi-gas solution – the GasAlertMax XT. Simultaneously monitoring for hydrogen sulfide (H2S) carbon monoxide (CO), oxygen (O2) and combustibles (%LEL), the GasAlertMax XT features a non-intrusive integrated sampling pump and SmartSample diaphragm pump technology. By offering one-button operation, the GasAlertMax XT provides ease of use and simple compliance to industry safety standards. Tamper-proof, user adjustable options enable the instrument to be customized to suit your specific application.
The GasAlertMax XT is ideally suited to a range of applications and customers including confined space entry, oil and gas, marine and shipping, utilities, wastewater treatment plants, power generation and municipal needs.
Powered by rechargeable batteries that provide enough power for an entire 13 hour shift, the compact GasAlertMax XT comes with standard event logging and datalogging. Calibration is simple with an automatic procedure. The GasAlertMax XT is compatible with the BW MicroDock II automatic test and calibration system. Multi-language support is available in English, French, German, Spanish and Portuguese.
For more information on the GasAlertMax XT, visit www.gasmonitors.com.
|
|
Compact Multi-gas Detector for H2S, CO, O2, Combustibles
The QRAE II is a full-featured, compact, one- to four-sensor gas detector for detection of combustibles, oxygen, hydrogen sulfide, and carbon monoxide. Key features include easy-to-change, externally accessed battery packs (available in rechargeable and alkaline versions), a water-resistant case and a new state-of-the-art O2 sensor technology with extended life.
Key features include:
Patented SPE O2? Oxygen sensor
Best EMI/RFI immunity technology for products in its class, eliminating radio interference
Easy access to sensors, filter and battery compartment without exposing electronic components to potential damage
Big graphic display for easy overview of gas type and concentration
Alkaline adapter and Lithium-ion battery pack
Rugged housing withstands harsh environments
|
|
|
FirstCheck is the very first multi-gas to combine complete VOC and toxic gas detection from 1 ppb up to 10,000 ppm with traditional multi-gas sensors for oxygen, hydrogen sulfied, carbon monoxide and explosive gas detection.
|
|
The MultiRAE Plus combines a PID (Photoionization Detector) with the standard four gases of a confined space monitor (O2, LEL, and two toxic gas sensors) in one compact monitor with sampling pump. The MultiRAE Plus gets the job done in more circumstances than any other gas detector. The MultiRAE Plus is quickly and easily changed from a sophisticated technician instrument to a simple text-only monitor. The same monitor can be used as a personal monitor, a hand-held sniffer, or as a continuous operational area monitor.
The MultiRAE Plus detector can be made wireless with the use of RAELink. This allows real-time monitoring information from the detector to be integrated into an existing AreaRAE system. A wireless, RF (radio frequency) modem allows detectors to communicate and transmit readings and other information on a real-time basis with a remotely located AreaRAE base controller up to two miles away.
This product has ATEX approval.
|
|
|
|
|
|
VA-3000/VS-3000 Multi-component Analyzer
Product Overview
From environmental monitoring to developing new energy sources and chemicals for the new era, gas analysis systems are faced with needs and challenges that have changed dramatically over time. Responding to these new needs, HORIBA has developed the VA-3000, the versatile gas analyzer that's ready for the future. A single analyzer is now capable of measuring a wider selection of gas components utilizing many different types of sensor technology. Non-dispersive infrared (NDIR) modules are available to measure gases such as CO, CO2, NO, N2O, CH4, SO2 and others. A chemiluminescent sensor module may be included to measure NO or NOx with a standard converter. And four different types of sensor modules are available to measure O2 - galvanic, paramagnetic, zirconium oxide or magnetopneumatic. Designed to be compact and lightweight, the VA-3000 may have up to three sensor modules installed in a single analyzer case. This unique feature means the VA-3000 can be used today for a broad range of applications including research and development or environmental pollution monitoring, where efficiency and space-saving are crucial.
|
|
SERVOPRO 1440 Gas Analyser
The 1440D provides a convenient solution for the measurement of one or two of the following gases: oxygen, carbon dioxide, carbon monoxide and methane.
- Excellent stability and performance
- Low maintenance
- No electrochemical cells to replace or renew
- Variants suitable for flammable / toxic sample gases
- 19” rack, panel mount or bench-top case options
- Concentration and low flow alarms
Technology Used
Oxygen – Servomex’ unique paramagnetic cell, which offers a fast, linear, accurate, highly stable and selective response in a non-depleting rugged package.
Carbon monoxide (CO), carbon dioxide (C02), Methane (CH4) – Single beam, single wavelength infrared technology, which gives a highly stable, selective measurement.
|
|
SERVOPRO 4100 Gas Analyser
The 4100 is designed to meet the process control and product qualification needs of industrial gas producers and users.
- Easy to set up and operate
- Low maintenance
- Extremely stable and reliable sensors
- Can measure up to four gases simultaneously
- External analogue input facilities
- RS232 / RS485 serial data output
- Modbus TM communications
|
|
|
|
|
|
3 Gas - Landfill Gas Monitoring System (Wall Mount) - GIR5000
- For measuring oxygen, methane and carbon dioxide gas
- Alarms for all measurements and sample flow
- 4 to 20mA outputs for all measurements
- Optional safety alarm and shut-down system
The GIR5000 gas landfill monitoring system is a gas analyzer unit for measuring and monitoring the concentrations of oxygen and methane in landfill gas and biogas. As an option, the concentration of carbon dioxide can also be monitored. Used for:
- Landfill gas monitoring devices-methane
- Hazardous components in landfill gas
- Landfill safety
- Landfill gas monitor
- Landfill gas
- Landfill gases
- Landfill health effects
- Landfill pollution
Sample conditioning in the basic unit is provided by an external coalescing filter and water catch-pot assembly. When the external temperature is below 35°C (the internal temperature of the analyser) this technique is the most economic. For situations where the sample temperature at source is significantly higher than the ambient temperature, and the sample is saturated with water, an optional sample cooler can be fitted.
Analogue outputs and alarms are provided for all gases measured.
|
|
Portable multi-functional
Analyser MAPY 4.0
for 02, C02, He or 02/C02
Analysing System for the monitoring of protective atmospheres in food packaging (MAP) and welding. For continuous analysis (in-line) and also intermittent sampling via a needle e.g. from food packs. A flexible analyser to guarantee quality and productivity of production processes. Available as a single or double analyser for carbon dioxide, oxygen, helium.
Benefits
- minimum sample gas required for analysis of smallest volumes (e.g. food packaging) fast response time
- fast measuring results of sampling
- simple to operate via touch-screen
- reliable steady measuring results and high accuracy through pressure compensation
- simple calibration of sensor
- permanent monitoring of set limit values
- alarm signals are given if the set limits are exceeded and a potential free contact operates to e.g. auto-stop your machine to avoid quality problems
- easy to clean stainless steel housing for maximum hygiene, splash-proof
|
|
|
|
|
|
The Rapidox 3100 provides fast and accurate analysis over a wide oxygen range using a rugged, long-life zirconia sensor. It is available in models to measure just oxygen, or oxygen plus either CO or CO2.
Easy to use and simple to calibrate using your choice of any two gases, the Rapidox 3100 offers the high performance and flexibility usually found only in much more expensive products.
The Rapidox 3100 incorporates a powerful and silent linear piston pump for remote sampling of gas. From the display to the outputs, all features are fully programmable using the keypad on the front panel. Connections are made using 6/4mm flexible tubing to the front panel input and output unions and the front panel includes a flow gauge allowing the user to control the rate of gas flow into the analyser.
The Rapidox is supplied with powerful Windows software for easy data-logging and graphing. Just switch on and start measuring...
- Bench mounted zirconia oxygen analyser with internal sensor & sample pump
- Rapid response long-life sensor
- Easy to calibrate using any two gases
- Fully programmable audible alarms with signal output
- Sample flow rate adjustable from 0 to 4 litres per minute
- Suitable for applications where the gas must be sampled remotely
- Gas is sampled through flexible tubing connected to the front of the analyser
- Perfect for analysis of room air and difficult to access locations
- Perfect for static gas applications
- Suitable for gases up to 150°C
|
|
|
|
|
|
The Rapidox SF6 Multimeter performs a rapid analysis of the condition of SF6 by measuring the concentration of SF6, moisture and SF6 products in the gas. SF6 in air or nitrogen is continually sampled and a programmable alarm will trigger if the results are outside a programmable range. The Rapidox 3100C is ideal for monitoring the condition gas-insulated equipment and guarding against electrical breakdown.
The Rapidox SF6 Multimeter allows the sampled gas to be recycled and recovered, ensuring that no SF6 is released into the atmosphere. It is supplied with powerful Windows software for easy data-logging and graphing. Just switch on and start measuring...
- Ideal for controlling the SF6 quality in bus bars and circuit breakers
- Continuous gas sampling of SF6, SO2 and moisture
- Ideal for detecting the presence of leaks
- The Rapidox SF6 Multimeter is ideal for checking for the build-up of corrosive decomposition products
- High-precision catharometer for SF6 analysis over the range 0-100%
- Full-scale ceramic dew point sensor for moisture analysis -100°C to +20°C
- Input pressure 0.5 to 14 bar
- Windows data logging software with graphing
|
|
|
|
|
|
Its unique modular principle means that the system can be constructed individually. You can configure your multi EA 5000 to meet your needs, thus creating your personal analysis system. No problem if your analytical requirements change, the modular structure of the multi EA 5000 can be extended at any time.
The unique double furnace technology makes it quick to switch between vertical and horizontal applications in one instrument, i.e. fast and optimum adaptation to the sample matrix and analysis standard with minimal effort.
The flame sensor technology guarantees matrix-optimized, quantitative combustion. Even unknown samples, whose properties are undocumented, can be analyzed soot-free, precisely and reliably today.
Forget time-consuming method generation and optimization of process parameters, such as gas flow, temperature, dosing speed – these are in the past!
- Application diversity, analyzes solid, paste, fluid, gaseous and LPG samples
- Multi-element, with C, N, S and Cl determination in one instrument
- Multimatrix sampler, for fully automated determination of solid and fluid samples in vertical or horizontal furnace configuration
- Double furnace technology, optimal adaptation to the sample matrix – vertical and horizontal mode in a single instrument
- Extended measuring range with low maintenance, ultra-modern detectors, all the way from ppb to percent
- Modular design, freedom to select and extend your analysis system configuration
- Self Check System (SCS) for trouble-free operation
- Flame sensor technology for matrix-optimized sample digestion
|
|
The Thermo Scientific TITAN 4000 is the ultimate Total Nitrogen,
Sulfur and Chlorine Analyzer, perfectly crafted for today’s
demanding laboratories. Powerful advances in technology deliver
brilliant results, with unprecedented sample throughput and
lowest cost of ownership.
• TN/TS analysis in less than 2 minutes
• Up to 60% reduction in bench space
• Consumable savings of at least 10% pa
• Future proof upgradeability
|
|
TCL-2100V can measure total chlorine/sulfur from trace level in fast, easy. New developed control and electrodes enable ppb level measurement in accurate and stable. It can be applicable to variety of liquid and gaseous sample by approved coulometric analysis. Trace chlorine analysis down to 0.05ppm in liquid sample and 0.2ppm in gaseous sample. Auto liquid/solid sample can be upgraded afterwards for automation. Open/close furnace offer improved maintenance ability and safety.
Horizontal version (TOX-2100H) enable to handle liquid, gas and solid sample.
|
|
TS-100V offer wide mesurement range from 0.02ppm to percent level in highest reliability by the contribution of Oxygen control combustion and unique optics.
The combination of the Ultra Violet Fluorescence method as a Sulfur detector and vertical furnace using Oxygen control combustion (patent pending) realize more defined trace Sulfur measurements for petroleum, petrochemical, fuel, biodiesels.
And it can be upgraded to simultaneous Sulfur and Nitrogen analysis afterwards very easily.
Wide option are available for various application, autoliquid sampler, Gas&LPG injector, Trap&release unit, Nitrogen detector.
Horizontal version also available for solid sample.
|
|
9000NS - TOTAL NITROGEN & SULFUR ANALYZER
Our 9000 Series Analyzers use proven technology to perform total nitrogen and/or total sulfur analyses from low ppb to percent levels. Their speed, accuracy, and precision are unrivalled — more stable than coulometric methods, more sensitive than x-ray, safer and faster than Kjeldahl.
These new generation analyzers include a computer with Windows™-based, custom-designed software. Data acquisition, analysis, and storage, as well as programming and control of the analyzer and accessory instrumentation are easy using the user friendly, menu driven interface. Remote instrument operation and real-time analysis support are provided via Remote Access.
|
|
|
The 200 Series of analyzers utilize the ultra-sensitive chemiluminescence technique for stable, precise measurements of NO, NO2, NOx, NH3 and O3. The 200 Series offers performance and quality that are unsurpassed in the industry.
|
|
In order to keep the NOx measurement in EPA method 7E and 20 in an economic frame, for example for applications like diesel NOx monitoring or automobile NOx monitoring, the conversion of NOx into NO with Nox Converter is the best economical and reliable solution.
The sample gas streams through a catalyst filled cartridge inserted into an oven which is heated up to over 400°C. The catalyst converts the NOx to NO and thus makes the analysis possible with IR analysers.
Gas Converter BÜNOx
Gas converter NO2 -> NO
High conversion rate at low temperature
Long lifetime
No cross-sensitivity on CO and H2O
Microcontroller
|
|
NDIR- und Thermal Conductivity Principle
for more than 14 different gases, from ppm up to Vol.% range.
CO,CO2,CH4,N2O,C3H8,C6H14,H2,He,Xe,Ne,Ar,SF6
OEM-Gastransmitter with improved characteristics
• NDIR-Dual wavelength sensor for gas measurement
• Low-grade drift characteristics
• Dual gas version or additional measurement range
• Fast response time
• Improved signal-to-noise ratio
• USB and RS485 interface
• Linearized analogue output: 4...20mA / 0...8V
• Display for measurement range deviation: 2...22mA output
• Temperature compensated
• Pressure compensation option
• Web based communication software
• Simple integration into analyzers and measurement systems • Versions for gas diffusion operation available
|
|
The oxygen analyser model ZOA 100 use a gazeous diffusion micro zirconium oxide cell.
This technic allows a continious or intermittent use with very low maintenance.
The several versions of ZOA 100 are designed to fit the most severe applications.
The unit is also designed to be used as oxygen detector.
|
|
|
Available for zone 1, ATEX
|
|
|
The XTP600 gas analyzer measures the percentage of oxygen in hydrogen, nitrogen or any hydrocarbon mixture. Thermoparamagnetic technology has been used to ensure the sensor is reliable and resistant to drift. This sensor is then built into an explosion proof casing which has been approved ATEX zone 1 for use in hazardous areas. As the sensor has no moving parts, vibration and movement will not affect the measurements over a long period of time. The outer casing of the XTP600 is strong and can be easily placed at the exact point of measurement. The XTP600’s maintenance time has been kept to a minimum by making sure the casing unscrews to allow easy access to the centre.
|
|
The XZR-400 oxygen analyzer detects trace oxygen and controls the purity of gases such as Carbon Dioxide, Helium, Nitrogen and Argon. To ensure a low cost of ownership, the XZR-400 uses a highly responsive zirconium oxide sensor with metallic sealed reference and S Type T/C. This instrument is easy to maintain and calibrate It also has a long sensor lifetime and is extremely quick and simple to install.
The XZR-400 is suitable to many applications and is available in three different versions; wall-mounted, rack-mounted and portable.
|
|
The Oxatex oxygen analyser is designed for the continuous measuring of oxygen content in combustion flue gas for industrial installations, such as:
- Power plants
- Refineries
- Heating installations
- Industrial waste incinerators
- Process control applications, etc.
The flue gas to be measured is fed to a zirconium micro-gauge by natural
circulation.
The measured reading is directly processed by the unit’s integrated electronics.
Advantages:
• Robust Industrial construction for daily use in the most difficult of environments.
• Reliability of readings by automatic programmable calibration at regular intervals (optional).
• An «all in» one concept, with integrated electronics for reduced installation costs.
• Easy setting of parameters, carried out by remote control
|
|
Series 3000T - Trace Oxygen Analyzers
The Series 3000T Trace Oxygen Analyzers provides powerful microprocessor technology while offering tremendous versatility in the low ppm ranges. This instrument offers three user-selectable linear ranges, high accuracy, fast response, adjustable alarms, and auto diagnostics.
No zero gases are required in most applications. The heart of the analyzer is a specially qualified Micro-fuel Cell designed to measure oxygen in the gas sample.
The sensor is unequaled in the industry for its accuracy, sensitivity, and reliability. The instruments can be used as a separate unit or as a component of a larger analytical system.
|
|
|
|
|
|
For the first time, the Vaisala SPECTRACAP® Oxygen Transmitter OMT355 offers Tunable Diode Laser (TDL) technology in a compact probe suitable for field use. The SPECTRACAP® sensor measures oxygen concentration optically by measuring the absorption of light from a tunable diode laser.
The OMT355 can be flange-mounted directly into a process without sampling or sample conditioning equipment. This provides the user real time measurement data without sampling or sample switching delays. In addition, the stainless steel probe tolerates aggressive chemicals and excessive amounts of moisture.
For processes with high temperatures, elevated pressures or excessive solids content, an optional sampling cell is available for the transmitter. As the sensor is very robust and has low sensitivity to gas flow and pressure variations, the associated sampling system is simple and can be installed near the sampling point.
The OMT355 is a low-maintenance instrument. A stainless steel mesh filter protects the probe optics from dust and dirt. An optional hydrophobic, porous PTFE filter is also available.
Typical applications for the OMT355 include gas generation, inert gas blanketing, fermentation and composting process monitoring.
|
|
|
|
Gas analyzers, Portable gas detectors 
