|
|
|
|
|
|
ER3000 Series:
Ideal to be used with air actuated devices such as regulators & control valves.
Electropneumatic digital controller.
High precision (0.1% accuracy) device.
RS485 network capabilities.
Free Software.
PID loop on board.
Explosion-proof housing available.
Extra analog/digital inputs/outputs available.
Applications:
Automated flow & pressure systems
High precision control equipment
Calibration of transmitters & gages
Burst & proof test stands
Blanketing applications
Vacuum control
ER3110 Series: Compact Integrated Unit
Integrates with 44-5200 regulator, standard options available
Features identical to the ER3000
Choice of outlet pressure ranges to 500 PSIG
Preference pressure: 100 PSIG
Flow capacity: Cv=0.06 or 0.15
Venting or non-venting
70-2000 Series: Motorized Actuator
24 VDC motorized actuator provides remote adjustment of regulator setpoint
Adaptable to 26-1000, 26-1600, 26-1700, 26-2300, 54-2000 and 54-2100 Series Regulators
Variable speed control with adjustable limit stops to prevent over-travel
Pressure Transducers:
Ideal for use in ER3000 applications where an external feedback is required
Provides extremely stable and repeatable hydraulic and pneumatic pressure measurements
.1%, 0.25% and 0.5% accuracy available
Choice of 4-20 mA, 0-10 VDC versions
Wide choice of pressure ranges (including sub-atmospheric)
|
|
Periodic filter cleaning with compressed air, simple water treatment plants, feeding systems, lighting controls, up to 9 output channels are controlled in a timed sequence. No special programming knowledge is required to put the device into operation.
|
|
The central unit MV5 ZE 101 was specially designed for the integration of marking units. Its extremely compact body is especially used for the installation as a front or back installation. It takes place in switchboards as well as on mounting plates. A direct connection to a a production line is given by type of protection IP54.
The MV5 ZE 101 works with a powerful processor and can be operated by an integrated display and an attached keyboard absolutely independend. A connection by INTERBUS or PROFIBUS is possible!
|
|
|
|
|
|
Programmable electronic controller mod. BRAIN
Reggiana Macchine Utensili has developed its own software and stepping motors control, this gives the maximum flexibility, able to suit all customers needs.
Suitable for both air assisted and electromagnetic marking heads, available as top bench or portable system with rechargeable battery.
With membrane keyboard and graphic display, allows communication:
with PC direct and wireless,
through RS232 / RS485, TCP/IP
from/to PLC,
I/O signals,
from Bar Code readers,
TXT files,
integrated USB key reader.
Easy to program and friendly use, BRAIN can manage all following functions:
1GB Memory (possibility to extend up to 8GB),
texts in line, angular, mirror,
arc-texts,
serial numbers,
batches of production,
time and date,
working shifts,
customized codes,
preview, diagnostic and many more.
The excellent management of the mechanical movements allows marking:
logos,
2D Matrix and OCR codes,
fonts per dots 5x7 and 11x16,
continuous line fonts.
Low maintenance and reliable, the programmable electronic controller BRAIN is complete with all above features, includes JOG function and can be easily connected to all accessories available, rotary and vertical automated axis, nameplate automatic loader and many others even tailored on request.
|
|
Characteristics
3x3-DGT Analyser
DIN-rail mounting
6-DIN modules housing
Dual digital output
RS485 communication port
Benefits
Pulse output for energy remote reading
Alarm outputs with OR/AND functions for a better extended variable control
Universal AC/DC power supply to cover all the application needs
|
|
|
The consumption of energy as uniformly as possible throughout the day offers the supplier the prospect of considerable savings. Agreeing a peak load rate also gives the end consumer the opportunity to significantly reduce his energy costs.
|
|
The Cascade controller offers automatic start/stop control and fault shutdown protection for generators, pumps and other stationary engine applications.
This Autostart controller is designed to fit any engine-driven application requiring a simple and robust automatic start/stop sequence.
Features:
- Compatible with electronic (J1939 CANbus) and standard engines.
- Fully programmable from the front facia
- Surge protected inputs, short circuit protected outputs
- High environmental protection: IP65/NEMA4 sealing, -40 to +85°C
- Rugged, encapsulated design to 10g/6g impact/vibration
- Murphylink® ready – works directly with PowerView™ analogue gauges
|
|
EMS - Engine Control Modules
An Engine Control Unit (ECU), also known as an Engine Management System (EMS), is an electronic system which controls various aspects of an internal combustion engine's operation. The Engine Control Unit provided by Delta offers more advanced technology for today's cars. It provides the necessary output and switch signals during both the start of a vehicle and normal operation. The outputs Delta offers include active crankshaft rotational speed signal, camshaft position signal, throttle position signal, coolant temperature signal and more. Switch signals include A/C request signal, A/C loading switch signal, diagnostics request signal and more. These solid functions ensure the best engine operation for the vehicle.
|
|
A cost-effective family of engine management systems that provide vehicle manufacturers with complete, easy-to-manage packages. The systems can help manufacturers meet demands for improved power, better fuel economy and reduced emissions. Manufacturers can tailor content to individual requirements.
Delphi can also provide necessary algorithms and calibration services as well components and on-board diagnostics to support most 4-, 6- and 8-cylinder gasoline direct injection engine programs including homogeneous mode and spray stratified combustion systems.
High Value, Mid-Function and High Function Engine Management Systems are also available.
|
|
The Keystart range provides manual start/stop and automatic fault protection for generators, pumps and other engine-driven applications:-
* Simple, compact design
* 92 x 92 mm or 68 x 68mm DIN panel cut-out
* Security keyswitch
* Fuel, starter and timed preheat control outputs
* LED and icon indication of preheat, fuel on and fault conditions
* Overspeed shutdown option, with link-selectable input source (magnetic pickup or AC generator)
|
|
|
|
|
|
Engine monitoring system Watch-free system model : WE500
- Larger screen size
The LCD screen size is enlarged from 12.1" to 15". The image resolution is enhanced from 800 x 600 pixels (SVGA) to 1024 x 768 pixels (XGA). The number of display colours is also increased from 12 to 16,777,216. Furthermore, two larger size of LCD displays can be connected externally as an option.
- Mimic screens are made available
- Remote control for pumps and valves
Mimic screens provide remote control for pumps, valves and other kind of devices.
- Hardcopy function is added
Hardcopy is available by using a printer comes standard with the system
- Trend analysis display feature is enhanced
All analogue measurements can be viewed anytime as trend diagrams for continuously sampling of them.
- Download feature is provided
Connecting a purpose-built PC to the system allows monitoring points to be added, deleted or changed on site.
- The all-in-one configuration and the dual hot standby capability are inherited
High serviceability and reliability of the system are contributed. The compact design with 700 mm width (80 mm wider than WE300HG) can minimize the installation space.
|
|
|
The Quartz explosion/flame proof design is FM/CSA approved and ATEX certified for use in hazardous environments. And with the epoxy coated anodized aluminum enclosure it may be used in corrosive heavy wash down areas as well.
|
|
|
The Quartz explosion/flame proof design is FM/CSA approved and ATEX certified for use in hazardous environments. And with the epoxy coated anodized aluminum enclosure it may be used in corrosive heavy wash down areas as well.
|
|
|
The Quartz explosion/flame proof design is FM/CSA approved and ATEX certified for use in hazardous environments. And with the epoxy coated anodized aluminum enclosure it may be used in corrosive heavy wash down areas as well.
|
|
|
The Quartz explosion/flame proof design is FM/CSA approved and ATEX certified for use in hazardous environments. And with the epoxy coated anodized aluminum enclosure it may be used in corrosive heavy wash down areas as well.
|
|
Switches and controllers
with integrated motor protection
switches: 1-, 2-, 3-step
Control unit:
transformer
5-step and stepless, electronic stepless
Regulated by:
stepless, temperature-, pressure-, humidity-, air velocity
Electronic Control Units
Electronic control units for stepless speed control of voltage-controlled 1- or 3-phase fans. The devices are available in various ratings and formats. Rosenberg offers electronic control units with manual speed selection as well as devices for simple control applications (temperature-pressure control).
|
|
|
|
|
|
The AD-4826 is a feeder controller with model predictive control technology that delivers superior performance when compared with PID control devices.
Model predictive control is a method of process control to determine a manipulated variable that enables a process variable to reach a set point by predicting future changes in a process using models of the controlled object’s behavior. The internal model is used to predict if any deviation from the set point will occur in the immediate future when process control is continued with the current manipulated variable. If a deviation is predicted, an adjusted manipulated variable is output and sent to the controlled object.
Unlike PID control, which executes a correction after a control deviation occurs, model predictive control predicts a deviation in advance using a model of the system’s behavior to enable stable process control while avoiding hunting (unstable movement). The extraordinary advantages of model predictive control include process control stability, disturbance cancellation, improved response to changes, improved set-point-following capability and high tolerance to the influence of changes in a process.
The AD-4826 can perform model predictive control with a screw feeder, circle feeder, table feeder or rotary feeder that has been controlled with PID control (up to 4 feeders can be used with one AD-4826 device).
Please see the AD-4826 catalog for further details.
|
|
Standard Composition
- 1 IP55 RAL 7032 METAL CASE
- 1 MAIN SWITCH WITH DOOR WITH FUSES
- 1 AC3 class ELECTROMAGNETIC SWITCH
- 1 3-PHASE THERMAL RELAY WITH MANUAL RESET
- 2 TRANSFORMER PRIMARY PROTECTION FUSES
- 1 SAFETY TRANSFORMER FOR LOW VOLTAGE AUXILIARIES
- 1 MAINS VOLTAGE LAMP
- 1 MOTOR RUNNING LAMP
- 1 THERMAL CUTOUT RELEASED LAMP
- 1 TERMINAL BOARD FOR WEEKLY TEST PREPARATION
- 1 AUTOMATIC-Ø-MANUAL SELECTOR
- 1 REMOTE SIGNALLING OF: pump in automatic position, pump excluded, pump in manual position
|
|
Hubbell Fire pump Motor Controllers are designed to comply with the latest standard of the National Fire Protection Association for the installation of stationary pumps for fire protection (NFPA-20).
LXi Microprocessor Logic & Control
Coordinated design engineered, built, tested and labeled by one manufacturer
Suitable for use as service entrance equipment
Full compliment of visual indicators
Communications port
LCD display shows simultaneous reading of all phases for amps and volts, and system pressure
Full range of horsepower ratings and voltages
Ample cable bending space
|
|
Flowcon: Automatic Flow Regulator
Accurate Control and Perfect Process Monitoring
- Precise, stable mold temperature through automatic control
- The development of this unit is based on many years of applied experience.
- Microprocessor controlled accuracy +/- 1°C
- Up to 8 zones can be controlled individually.
- Storage of setup data for 7 different molds
- A tolerance window can be set on the display. If the temperature exceeds the tolerance a buzzer or alarm contact is activated.
- Serial interface for data transfer to lmm standard
- Secures the quality of the molding process by perfect temperature control and monitoring.
- Plunger type solenoid valves with large seat diameter ensure operation even with poor water quality.
|
|
FS5000 Flow Switch Controller
The FS5000 Flow Switch Controller is designed for use in applications that require flow/no-flow control of metering pumps and other devices. It includes a flow switch and three (3) 115V receptacles that are powered with flow and one (1) 115V service receptacle. Power indicator light, flow indicator light and test switch are included.
|
|
|
The REOVIB series of variablefrequency regulators is specially designed for controlling vibratory feeders. The units produce a highly stable output frequency that is adjustable in 0.1 Hz increments. Manual “tuning” time of the mechanical feed system is significantly reduced. Thanks to the sinusoidal output, the feeder runs quietly and ensures gentle product handling. Settings are adjusted by using a touchpanel and an integrated digital display. The feed rate setpoint can be adjusted externally in several ways, including the use of 0...10 VDC or 0(4)...20 mA signals. Four sets of user parameters can be stored and recalled. The current limit setting is used to protect the electromagnetic coil against overloads. The frequency range “window” can be used to limit the adjustment band available to the user. Track control (backlog control) and amplitude regulation are standard features of the unit.
|
|
The Danfoss VLT 6000 HVAC, dedicated to HVAC applications, provides unsurpassed performance, energy savings and improved control of HVAC systems – including interfacing with building management systems.
Precise control of temperature, pressure, and flow in HVAC applications result in the best environmental performance for building owners and operators.
|
|
PROCUT is a new Guillotine Control System for paper cutting machines running over our PCM2 Motion Controller. It takes great advantage of new technology in motion control, making all the movements as accurate as possible. PROCUT is a complete system so you will be up and running quickly. The accuracy and friendly user interface helps you obtain great results again and again.
Main features:
* Easy to install and use
* Improve production
* Improve quality of final product
* Memory capacity for 100 programs up to 1000 lines each
* Graphic Colour LCD Screen - 320 x 240 Pixels
* Automatic push out of paper: to help the operator to handle the paper
* Air table control
* Label Optimisation Mode
* Quick cut mode
* ‘Teach’ mode programming
* Loop quantity programmable
* Encoder Feedback
* Imperial and metric
|
|
Advanced Control Features:
- Displacement and force monitoring
- Force control
- Envelope function
- Combo mode
- Energy and time limits
The HF27 High Frequency Inverter precisely controls and monitors electrical AND mechanical weld parameters. Miniature welds are highly sensitive to small heat profile fluctuations in the resistance welding process. Overheating deforms and destroys parts, while under heating results in a weak, unacceptable bond. To achieve consistent, reliable welds of small to microminiature parts, precisely controlled heating is required. This necessitates superior control of the energy output.
|
|
|
|
|
|
Interlock control system
A plug-in modular system for linking up to 10 doors, or up to 10 groups of doors to create an interlock system.
No complicated control system required as dependencies are set on site with DIP-switches at each control module. The system allows for easy expansion.
Quite often one of the requirements of clean-room technology or laboratories is, that certain doors may only be opened ifothers are closed. The DICTATOR interlock control system is the idealsolution to link units of up to 10 doors.
The dependencies between different doors are programmed directly in the
respective control modules on each door using a very easy adjustable matrix control system. This is done with DIP-switches representing the different doors. The dependences / linksnbetween the doors can also be changed on site at a later stage, not requiring any special programming
know-how. The interlock control terminal is provided with a potentialfree make-break contact. This permits e.g. to pass on the information on each door to a central control system.
The DICTATOR interlock control system is a modular system and therefore
extremely flexible and easy to adapt to different sizes of door units and
requirements.
|
|
Characteristics
0 to 200Hz output frequency
V/f control with several preset and one user definable V/f patterns
Very low audible motor noise thanks to the optimised PWM control
Built in DC reactor and dual diode input (12 pulse) for harmonics reduction on models of 22kW and above
Intelligent energy saving function
Integrated PI controller with HVAC dedicated functions
High Slip Braking (Can reduce the deceleration time without using a braking resistor)
Very smooth speed search function working in both directions
Available Communications options:
- DeviceNet
- Profibus-DP
- Interbus-S
- CANopen
- LONWorks
Integrated RS-422/485 port for Memobus communications
HOA operator (optional)
CE, UL, cUL and German Lloyd compliant
|
|
|
Yaskawa is the largest global variable frequency drives manufacturer with over 30 years of Building Automation System (BAS) and HVAC experience. Our variable frequency drives are designed for HVAC applications, which include air handlers, cooling towers and pumps, by combining reduced size and cost with step changes in performance and quality. The drive features for Building Automation Systems include extensive parameter selection which simplifies management of BAS applications for energy efficiency and closed loop control, industry-standard Hand/Off/Auto functionality, an internal PI controller and a Sleep function. Because all variable frequency drives (VFDs) are rigorously tested, Yaskawa ensures that quality and reliability are designed and built in.
|
|
|
|
Controllers and Regulators for specific applications
