|
|
| The MP720 positive opening position switching is a dependent-action, changeover, double-gap, contact element, which is connected by means of a cable directly overmoulded into the housing. |
|
Several E-Stop switches professional fitting to the following product ranges:
- Pushbuttons LUMOTAST 25
- Industrial control units RAFIX 16
- Control Units RAFIX 16F
- Control Units RAFIX 22 QR
NEW: Control Units for AS-Interface bus. |
|
It is assembled as an addition to a door latch
It avoids accidents related to the possible locking of an operator in a dangerous area.
It is equipped with a push button and safety contact block for the equipment emergency stop, the DEU adapts to all types of door latches and it is installed inside the protected area.
The emergency evacuation device forces ejection of the latch. The pushing the button frees the latch and stops the machine immediately due to a 2 0 safety contact and permits opening of the access by pushing the door.
EMERGENCY EVACUATION DEVICE
In case of emergency:
1 – The locked-in operator professional presses the push button.
2 – The latch separates from the DEU.
3 – The safety contact opens the emergency stop circuit.
To re-start, it will be necessary to unblock the latch after the installation is safe.
The latch must be assembled in the fixed part of the access.
Options
- Without contacts |
|
TH-Contact emergency stop button
Découpe de montage (mm) : Ø 16,2 / Ø 22,5
Caractéristiques :
• conforme aux directives EN-418
• étanchéité IP66 ou IP67
• déverrouillage par rotation, par traction ou à clé
• calotte à disque jaune (en option)
• 1 contact à fermeture et 1 contact à ouverture, 2 pôles de contacts à ouverture
Pouvoir de coupure 250 V/CA, 6 A
Dimensions (mm) : Ø 27 x 49 ; Ø 40 x 61,7
Organe de commande :
• capuchon coup de poing rouge
• clé KABA
Homologations : IEC 947-5-1/947-5-5
|
|
Even redundant, secure emergency-stop chains are ineffective unless the contact block is accurately connected with the emergency-stop button. The patented safety contact blocks of Schlegel Elektrokontakt are the response to this danger that may occur e.g. due to a negligent assembly or a mechanical damage.
In such an emergency they ensure that the emergency function is activated and that the installation is immediately shutdown. It can only be started up again after trouble-shooting.
The contact blocks are available with screw connections or Faston terminals and do have positive opening contacts acc. to IEC60947-5-1. They can be supplied with one or two channels and also, once combined with the relative E-stop button, in a foolproof version acc. to EN60947-5-5 and EN418. The high-quality contact elements allow reliable switching even of low currents (5mA at 24V or less). They are available as conventional contact blocks as well as for the AS-Interface-Bus (Safety@Work). |
|
Thermoplastic enclosure
Slow action
max. 2 contacts
Fixings to DIN EN 50047
Cable |
|
Control units EX
A product range flexible devices:
- Study and manufacture
- Personalization according to your needs: pushbuttons, indicators
- Coffrest STAINLESS, polyester and aluminum
|
|
Control Unit System Series ConSig 8040
Control Unit System Series ConSig 8040 Equipped with Contact Block 8208
Control Unit System Series ConSig 7040
Control Station in Unsaturated polyester resin Series 8146
Control Station in Sheet Steel or Stainless Steel Series 8125
Fire Alarm Station Series 8146/5052
Control Button Series 8082
Illuminated Pushbutton Series 8082/8010
Indicating Lamp Series 8010
Control Switches Series 8008
Amp meter / Voltmeter Series 8402, 8403, 8405, 8404
Potentiometer manufacturers Series 8208
Contact Block Series 8208
Resistor Series 8453/1 and 8453/2
|
|
Explosion protection to
CENELEC
IEC
For use in
Zone 1 and Zone 2
Zone 21 and Zone 22
Degree of protection IP 65
Robust moulded plastic enclosure
Large switch lever with phosphorescent inlaid strip |
|
This range allows you to easily create your own solutions by selection the modules and simply click them together, the range exists of:
- pushbuttons
- selector switches
- mushroom buttons
- emergency stops
- key interlocks
- professional door locks
- lamps
- start re-start buttons
- interconnections for both as-i or bus systems
|
|
Pushbuttons are switching devices which close and open electrical circuits. Actuators suppliers and contact chambers of pushbuttons are always integrated into one product (as opposed to control units). The "LUMOTAST" product families also include signal lamps, keylock and selector switches which are compatible with the pushbuttons in design and technology.
Illuminated pushbuttons, 8 mm range, mounting hole diameter 8 mm
LUMOTAST illuminated pushbutton range, mounting hole diameter 16,2 mm
LUMOTAST FK, with flat-ribbon cable suppliers of connector
LUMOTAST 25, actuating area 25 x 25 mm
LUMOTAST 75, for up to 250V /4 A
Keylock switch, mounting hole diameter 16,2 mm
Other pushbuttons, mounting hole diameter 9,1 mm - 20,3 mm |
|
Provides momentary switching in a compact,
saving up to 25% of usually
required space needed by other popular models.
These small switches are ideal for professional keyboard matrix
assemblies and with their new recessed lens they
offer even greater compactness and beauty. |
|
The GE Push Button offering includes a complete line of pilot devices and stations for industrial and commecrial applications. They are available in 30mm and in 22mm sizes.
They are available in 30mm and in 22mm sizes.
The C-2000TM 22mm push button line has interchangeable components that snap together, simplifying assembly, reducing inventory requirements, and increasing flexibility.
Features and Benefits
Ultrasonically welded contact block - provide superior environmental protection.
Double bridge contacts - provide excellent performance even in low-voltage applications.
Permanently bonded front gasket-provide superior sealing against contaminants and makes installation foolproof. |
|
J1800 - Format DIN 96x96
J2000 - J2400 (J2100 / J2200 / J2300) - Format DIN 144x144.
The most basic models.
They are intended to replace filament indicator lights on professional cabinet front panels.
- 8, 12 or 24 "high luminosity" leds.
- Light up on closing of the input contact.
- "Test led" buttons on the front panel.
- Labels are easy to make (on PC).
- Economical and strong.
Option:
Remote carry "synthesis" relay, selection is channel by channel. No reset possible.
(See also the J1900 / J3000 / J3500 range of alarm sequence panels)
|
|
EZ-LIGHTTM Operator Indicator Lights
- Professional displays multiple colors of highly visible LEDs in each unit
- Offers five housing styles for easy integration
- Replaces post or stack lights with a single compact unit
- Installs without certified personnel, near the operator
- Several configurations for a variety of applications
- Displays one to five colors, depending on model
- Eliminates industrial bulb replacement with long-lasting LEDs
- Compatible with MANUFACTURERS OF PLC or other logic-level control outputs
- IP67 for direct machine mounting
|
|
This range of panel mounting Light emitting diode indicators consists of many different bezel styles, types of LED’s and colours. The range has developed to meet the many different needs of panel design including IP67 environmentally sealed versions for use where a front panel professional seal is needed.
The vandal resistant LED indicators are designed to complement the vandal resistant switches (see the Switch Section, page 177), they have similar professional profiles with stainless steel bodies, sealing to IP66 & 68 and are built to withstand harsh environments.
|
|
| EAO indicators / pilot lights with protection up to IP 67 and different coloured professional lenses and LED illumination. The indicator / pilot light can be modified with bezels for raised or flush mounting. |
|
KRN - Pilot Light Head
description:
Body: LMN -
Pilot Light Head 24 x 18 mm
description:
with labelling option
LXJL5 - Pilot Light 54 x 27 mm
description:
T5.5K socket
LXJN - Pilot Light Head 54 x 27 mm
description:
with labelling option
LXJNN - Pilot Light Head 54 x 57 mm- IP40
description:
accepts 2 separate lampholders, with labelling option
LXL5 - Pilot Light 25 x 50 mm
description:
with labelling option
|
|
| EAO key lock switches with the option of 2 or 3 positions and protection up to IP 67. The key lock switch can be modified with bezels for raised or flush mounting. |
|
The Keyswitch consists of a 2NO/2NC contact arrangement which is wired into the machine circuits. Removal of the key selects machine stop at the end of a run down cycle. When the electro magnet had been energised within the AutoLok, or AmLok access can be gained. The operator takes the safety key into the hazardous area preventing inadvertent restart of the machinery.
|
|
Honeywell's Hobbs key switches are custom engineered, environmentally sealed, sliding contact switches. They can be designed to match existing keys or to use a six tumbler mechanism with up to 300 unique key combinations. The stainless steel keyhole shroud and keyhole dust shutter contribute to the durability of the assembly while O-rings protect the contact and rotor assembly from moisture and contamination.
Key switches can be used in off-highway, material handling or any other application where environmental specifications must be met. They have been tested for temperature, vibration, dust, cycling, humidity, pressure wash and salt fog and mount into a 22,10 mm (0.87 in) hole in panels 3,81 mm to 6,35 mm (0.15 in to 0.25 in) thick. |
|
TH-Contact key lock switch
Features:
a range of robust high quality 2 and 3 position key switches
supplied complete with precision made cylinders for maximum security.
A large selection of different coded locks and central locking keys make up the programme;
special key coding is available upon request. |
|
| This appliance is used to simultaneously perform a certain number of operations and insert a block which requires manual intervention in order to be cancelled. It is used in conjunction with automatic protective devices and intervenes in the event of machine faults of such nature as to require an inspection or check on service conditions. Therefore the lock-out relay prevents restoration of service until the standards conditions have been manually reset. |
|
| The KO Series keylock switches come in multiple styles with many combinations. Included are the barrel and flat key options, variety of key code options. Also available are the Keylock covers, the KOM and KOC series. Please see the PDF data sheet to the left to view all the different options. |
|
|
|