|
|
Hot Tap provides accurate flow rate measurement in full and pressurized pipe applications in pipes 18" (460 mm) diameter or larger.
Hot Tap combines ADFM pulse Doppler velocity profiling technology with a unique sensor assembly suitable for insertion into full, operating 18” and larger diameter pipes. It measures flow rate to within ±2% of actual flow rate, even in difficult applications such as installations near bends, short straight runs, near pumps, etc. Applications include:
- Wastewater collection systems
- Combined sewer systems
- Wastewater treatment facilities
- Irrigation canals and channels
- Industrial process
- Stormwater outfalls
|
|
The Heat Calculator Option of FLEXIM's non invasive FLUXUS ADM flow meter allows the easy determination of the energy flow in a system.
With temperature measurements made at the inlet and at the outlet of a system as well as flow measurement at the outlet , FLUXUS calculates the Heat Flow or energy usage within that system. All this is done with temperature and flow measurement devices mounted on the outside of a pipe.
FLUXUS will display the actual heat flow through the system, and if needed, totalize the heat flow in order to obtain the heat quantity.
The values can easily be transmitted to a PC for display and analysis. The data obtained can be used for energy flow balancing or it can be transmitted to a process control system.
|
|
Volume Flow Measuring System D-FL 200
Measuring system for ultra-sonic measuring of velocity and volume flow, especially for wet and aggressive smoke emissions (waste incineration).
Measuring system for ultra-sonic measuring of velocity and volume flow, especially for wet and aggressive smoke emissions (waste incineration)
Features
In-situ measuring method
Measurement possible below dew point and for high dust concentrations
Continuous measurement of normal volume flow and gas velocity
Automatic zero point and reference point control
Direct connection for temperature and pressure correction
Parameter input via keyboard or PC
Continuous temperature measuring
Applications
Volume flow measuring at low speeds
Plants with damp and/or aggressive exhaust gas, e.g. in waste incineration plants.
Volume flow measurement at high dust content
|
|
FLUXUS® G709 is an ultrasonic flowmeter for permanent installation in 19" rack systems.
In addition to the flow channels, FLUXUS® G709 can be equipped with up to 4 process inputs. With its wide range of electrical inputs and outputs, it can handle and process a great variety of process parameters.
The integrated flow calculator can perform a standard volume flow or mass flow correction according to ISO 12213-1. The connection of external process pressure and temperature measurements is needed for the calculation.
An extended status display helps the user to judge the measuring situation and current measuring precision directly during the measurement.
|
|
Minisonic G is an accurate and economical instrument for the instantaneous actual flowrate measurement of gas. The flowmeter accepts the PTZ corrector to obtain the normal flowrate. This ultrasonic instrument resolves all industrial needs.
In standard they offer :
• A display of flow and volume, of the direction and gas velocity,
• One 4-20mA output, 2 relays, 1 serial link, 1 software for PC.
It includes a very lastest electronic technology combined with highly digital signal porcessing technics and with more resources such as :
• echo analyser with automatic control (ESC mode : 'auto-focus' for the ultrasonic signals)
• zero offset adjustment for a reliable results
• high resolution time measurement < 0.1 ns
• an enhanced emission power
• a better noise rejection
• ergonomic keypad and menu calibration backlighted display
• possible to set a second 4-20 mA output
|
|
The solution for extreme temperatures
The WaveInjector® enables flow measurement at both very low and very high temperatures (400°C), even in explosion-hazard areas. It offers you the well known advantage of the clamp-on ultrasonic technology: a non-invasive, pressure and medium independant measurement with a high dynamic range and a high flexibility.
No special transducers are needed for the high-temperature measurement. The standard transducers are simply fixed to the WaveInjector®. For very large pipes, a special WaveInjector® version with chains guarantees a robust fixation on the pipe and a high surface pressure on the coupling point.
|
|
Hybrid
Blue-White introduces Sonic-ProTM Hybrid Ultrasonic Flowmeters.
Sonic-Pro has the ability to measure fluid flow using either Doppler or Transit Time methods. Additional features include: Non invasive clamp-on transducers; Custom metric algorithms and DSP technology ensures reliable, accurate measurement; easy reading LCD; data is logged to a standard SD card format supplied with each unit; isolated 4-20 mA output is fully configurable; 0 - 1000Hz Pulse Output is fully configurable; computer connection permits remote access to, and control of, all functions including: real time display, system configuration, data logging, remote data capture and process control functions. Sonic-Pro is IP66.
|
|
Electonic Flow Switch for flow monitoring with ultrasonic sensor, digital display, 2 set points and analog output, linearity error 2,5% m.v.
Features:
7-segment LED dispaly, microprocessor-controlled, self monitoring with error display. All prameteers are configured by keypad, tamper proof, keypad lock, rugged construction, vibration- and shock-proof, long term stability
Applications:
OEM-applications, automotive, automobile industry, cooling
|
|
|
Dynasonics manufactures transit time and Doppler ultrasonic flow meters, in fixed-position, portable and multi-channel versions. These meters are totally non-invasive and easy to install and operate. For clean or dirty liquids, Dynasonics products provide high accuracy measurements on a wide range of pipe materials, diameters and temperatures.
|
|
The FLUXUS ® ADM 5107 ultrasonic flowmeter for permanent installation was designed for the water- and wastewater industry.
The watertight transducers are small and practical, fast to install They are watertight and equipped with fixed transducer wiring. On request, the instrument can be pre-configured at the factory so as to reduce commissioning work to a minimum. Thanks to the clamp-on technology, no cutting or welding work is needed to mount the transducers on the pipe.
|
|
Time DELTA
This ultrasonic fixed type flowmeter consists of two sensors clamped on the pipe (DN 50 to 6000 mm, according to sensors) and of a digital converter, remote mounted. It can measure bi-directional flow speeds from -32 to +32 m/s. A display and an integrated keyboard allow the user to configure and to check all the settings.
In addition to the 4-20 mA output, the Time Delta is equipped with a totalization function, an automatic range change, 2 alarms and 2 configurable contact outputs. The converter and the sensors have IP67 protection.
|
|
The UFM 3030 is the universal meter for almost all applications to measure liquids in the chemical and petrochemical, oil production and refining, water and wastewater industry.
|
|
The SONOFLOW sensors, detecting the flow of liquids in thin tubes, constitute a new sensor series for the device automation. The newly developed method serves for a fast and safe identification of the flow rate or the flow volume of liquids respectively. The SONOFLOW is used in the medical technology, automation industry, device- and machine construction as well as in the pharmaceutical plant construction sector.
In order to be able to offer cost-effective flow sensors, we aimed for a modular construction of the measuring cell. It consists of 2 ultrasonic sensors, the metering box and the evaluation electronics. The measuring cell is integrated in the tube.
Due to the use of special inert materials for the measuring cell and the sterile measuring method the system provides great advantages in areas with strict hygienic standards.
Besides standardized applications there is also the opportunity to produce customized SONOFLOW sensors.
|
|
|
|
|
|
Our Innova-Sonic digital liquid flow meters are state-of-the-art universal transit-time instruments incorporating the latest advances in digital signal processing. The Innova-Sonic™ Portable Model 210 clamp-on features an industry-unique Bluetooth® wireless PDA interface for a truly flexible and convenient liquid flow measurement tool. Innova-Sonic™ Model 205 is our dedicated/fixed display readout version with non-invasive clamp-on transducers.
Our Innova-Sonic™ Insertion Model 205 features insertion transducers resulting in high signal strength in challenging applications and extremely large pipes.
While principally designed for clean liquid applications, all instruments in our Innova-Sonic family are tolerant of liquids with small amounts of air bubbles or suspended solids common in most industrial environments. All Innova-Sonic liquid flow meters offer low power consumption, high reliability and outstanding applicability at an economical cost.
UNIQUE PRODUCT FEATURES
- Accuracy better than +/-1%
- Wide operating temperature range -40F to +212F (-40C to 100C) (210 Innov-Sonic)
- One meter for a wide range of pipe sizes 1-200” (25mm-5000mm)
- 256MB Tungsten™ T5 PDA interface with Bluetooth wireless
- Numerical and graphical display interface
- Battery power supply with battery recharge port (including spare battery)
- Low installation effort and costs
- Wide bi-directional Flow range of 0 to 40 fps
-Measurement is independent of fluid conductivity
|
|
MINISONIC 600 and MINISONIC 2000 are accurate and economical instruments for the flow or volume measurements of liquids in full pipes.
These ultrasonic instruments resolve in that way most of industrial needs.
In standard they offer :
a display of the flowrate and volume, of the direction and flow speed
one 4-20 mA output, 2 relays, 1 serial link, 1 software for PC
Better performance and greater intelligence thanks to a new board (CE) and to more resources such as :
new measurement technology 'ESC' (or Echo Shape control)
measurement resolution <0.1 ns
higher amplification gain range and noise rejection
ergonomic keypad and menu calibration, backlighted display
Possible to set a second 4-20 mA output
|
|
|
|
|
|
deltawave Ultrasonic flowmeter
Our new measuring system deltawave is not only a precise flowmeter for open channels,filles and partially filled pipes but also a temperatur meter and a flow profile analysis tool. Due to the unique patent pending signal analysis deltawave works under extreme conditions, maintenance-free, calibration-free and reliably. The measurement system monitors itself continously and the multi-channel property ensures redundant safety. With only one deltawave, you can realize up to four independent measurement sites, significantly reducing the equipment cost. This feature, combined with the high accuracy up to 0.5% makes deltawave to one of the most powerful measuring systems.
Because of the high accuracy, field acceptance tests of hydraulic turbines, storage pumps and pump-turbines are possible due to ISO60041 and ASME PTC 18. Accuracies up to 1% could be achieved in open channels without calibration. In filled pipes or channels you will get an accuracy of 0.5% of reading. But measuring with deltawave do not means only accuracy. The optimized transducers ensures long-term stable measuring without maintenance. This has been proven successfully by public authorities.
|
|
LEFM® technology was installed on the first petroleum application in 1972. By 1976 a leak detection system in Alaska using 48 inch LEFM meters was installed and continues to operate today.
Caldon played a key role in establishing the API standard for measuring liquid hydrocarbons with transit time ultrasonic flow meters.
LEFM Series 200 flow meters are used in all areas of Petroleum processing - gathering, production, and distribution - by companies all over the world. The SoundTrack system is used to measure the relative density and kinematic viscosity of petroleum fluids.This information can provide interface detection in pipelines that carry multiple products.
|
|
|
|
|
|
FLOMOTION SYSTEMS BE6000
Flowmeter
Combines reliable full-pipe flow measurement with high accuracy, low-cost and ease of installation.
BE6000
Clamp-on type ultrasonic flowmeters offer the the simplest and easiest installation of any flowmeter. The BE6000 series transit-time flowmeter is no exception and installs in minutes. A pair of rugged transducers mounts easily to the outside of the pipe using standard clamping straps.
The transducers are non-intrusive, therefore there is no pressure drop or flow obstruction. The advanced microprocessor utilizes the latest in ultrasonic direct time measurement with a resolution of 0.2 nanoseconds. Coupled with state-of-the-art data processing the BE6000 series provides a high level of linearity.
Various inputs and outputs are available to interface with a wide variety of control and reporting systems. Remote programming is available via the standard RS232C port.
* Pipe sizes from 0.75 to 120 in. (20 - 3000mm).
* Velocities from -53 to +53 fps (-16 to + 16 m/s).
* Accuracy to 1.0%, repeatability to ±0.2%.
* Easy to install clamp-on transducers are compatible with plastics steel, stainless steel, cast iron, concrete, other materials.
* Outputs: 4-20mA, 0-20mA, frequency, relay, serial communications.
* 2 line x 20 digit backlight LCD display & integral 16 button keypad.
|
|
|
|
|
|
Oil Flow Meter - Ultrasonic Liquid Flow Sensor
The oil flow meter has been developed for ‘real time’ liquid measurement with specific attention given to the mechanical packaging to allow dyno and ‘on car’ correlation of data. The sensor installs directly into a suitable existing pipeline modified to accept flexible -16 tube connector couplings.
The system uses the established ultrasonic ‘time of flight’ measurement principle. The flow tube, transducers and mounting arrangement are compatible with an installation on an engine, capable of measuring liquid flow of up to 200 litres/min and temperatures of up to 150°C.
The remote processing electronics are rated for 105°C and can be placed up to one metre away from the flow tube. These electronics provide the user with flow data over a USB or analogue interface and can be powered from an automotive supply of 5 to 24 volts.
- 0-200 l/min Flow Rate
- No Moving Sensor Parts
- High Temperature Operation to 150°C
- No Pressure Drop
- Thermally Stable
- Compact (25mm x 160mm)
- Lightweight (140g)
- 16 Tube Connectors
|
|
|
|
|
|
Flowmax 22i/44i
Flowmax 22i and Flowmax 44i are flowmeters for measuring liquid flow by calculating the volume flow rate in the liquid. Based on the Ultrasonic-Technology Flowmax is able to measure conductible and not conductible liquids contactless.
Flowmax suits for continuous volume measurements and with its 250 Measurements/Second also for very dynamic applications. Flowmax has no moving parts and is free of wear. The design of the pipe minimizes dead volumes over the whole geometry. All parts having contact to the medium are PSU.
Therefore Flowmax can be used for a big amount of different medias like: distillated water, body cares, cosmetics, fluid food, alkaline liquids, toxic or aggressive media like concentrated acids and leaches. CIP cleaning processes are possible. Flowmax advantage is its high measuring accuracy and repeatability.
The measuring result is provided over a scalable pulse output. Programming and visualizing of the analog output is done via a RS485 interface. It is possible to share all measured information with IT-systems on the computer.
Flowmax 44i shows the measured flow in series on a background lighted display with actual flow and volume counter. Standard programming can be done by the keypad. Additional to the editable pulse output there are, current output, two digital outputs and one digital input available.
All parameters of the flowmeter are individually configurable with MIB PC-Software FlowSoft and USBtoRS485-Converter. The integrated gas control with empty pipe detection on the alarm output offers additional information.
|
|
The flow sensor (model 473) has two pulse outputs
volume pulse output
output for testing (high resolution pulse output for test laboratories, temporary limited) and for communication.
|
|
The FLUXUS® ADM 8127 ultrasonic flowmeter was specially designed for offshore applications. Its housing is made entirely of stainless steel. It is seawater-proof and ATEX approved for use in explosive atmosphere zones 1 and 2. All electronic components are in a flameproof enclosure with protection degree IP66. Terminals and terminal boxes are designed with protection type Ex-e "increased safety".
|
|
The Pulsar Ultra 3 & 5, coupled with the 125kHz high-accuracy dBMACH3 transducer, is a great solution for non-contacting open channel flow applications.
Measuring to BS3680 and operating with all standard flumes and weirs, Flow Oracle provides reliable flow measurement for both water industry and general industrial users.
|
|
Isco 2100
No single measurement technology is suitable for all open channel flow monitoring applications. Only Isco offers you a choice of ultrasonic, submerged probe, bubbler, and area velocity flow meters. Whether you need a permanent meter for a flume or weir, short term measurement with no primary device, or flow and pump performance monitoring at a lift station, Isco has the solution. And our application experts are available for a free, no obligation consultation to help you choose the best technology for your monitoring sites.
|
|
|
|
|
|
deltawave - Ultrasonic multimeter for fluids
Our new measuring system deltawave is not only a precise flowmeter for open channels,filles and partially filled pipes but also a temperatur meter and a flow profile analysis tool. Due to the unique patent pending signal analysis deltawave works under extreme conditions, maintenance-free, calibration-free and reliably. The measurement system monitors itself continously and the multi-channel property ensures redundant safety. With only one deltawave, you can realize up to four independent measurement sites, significantly reducing the equipment cost. This feature, combined with the high accuracy up to 0.5% makes deltawave to one of the most powerful measuring systems.
Because of the high accuracy, field acceptance tests of hydraulic turbines, storage pumps and pump-turbines are possible due to ISO60041 and ASME PTC 18. Accuracies up to 1% could be achieved in open channels without calibration. In filled pipes or channels you will get an accuracy of 0.5% of reading. But measuring with deltawave do not means only accuracy. The optimized transducers ensures long-term stable measuring without maintenance. This has been proven successfully by public authorities.
|
|
|
|
|
|
The FLOMOTION 900 provides accurate non-contact ultrasonic open channel flow measurement. Simple programming allows selection from a list of common built-in weir and flume tables. In addition, head vs. flow data points may be input for almost any type of primary device.
The integral display and keypad allows for fast, simple programming and operational indication. A real time clock and datalogging capabilities allow up to 6 months of flow information to be stored in memory.
Adjustable damping, transducer transmit power, and low flow cutout provide flexibility in difficult monitoring applications.
FLOMOTION 900 FEATURES
* Simple menu driven programming
* Large, backlit, multi-function LCD display
* Integral 5-position keypad
* 4-20mA and 3 relay outputs
* Integral datalogging with RS-232C output
* Built-in weir and flume tables
* Sampler trigger output
* Full diagnostics
* Intrinsically safe sensor suitable for use in hazardous locations
* Submersible sensor with temperature compensation
|
|
In-line ultrasonic flowmeters
The SITRANS F US wetted ultrasonic flowmeters are used to measure electrically conductive and non-conductive liquids that are acoustically permeable. They come in sensor sizes from DN 50 to 1200 (2 to 48 inches) and as wetted retrofit flowmeters up to DN 4000 (160 inches).
The program offers the possibility of comprehensive self-diagnostic capabilities for error indication and logging, the possibility to exchange transducers without interrupting operation, HART and PROFIBUS PA communication, custody transfer accuracy and ATEX approvals.
|
|
| ... products without technical information |
| |
|
|
Ultrasonic flow-meters
