|
|
Novafix MR1K-...GM/GK
Mechanical Flow Switch for liquids or gaseous media with spring supported piston and magnetic actuation of a reed switch. Robust design produced in materials brass or stainless steel.
compact dimension
good repeatabilty
dirt-resistance
high switch capability
hermetic separation of mechanical and electrical component
|
|
- Piston type
- Liquids and gas application
- Interchangeable switch head
- Nickel plated Brass or St. Steel
- 1/4" to 1" female thread process connections
- Adjustable reanges from 0,04 to 60 l/min.
- SPDT reed switch 250 Vac - 1,5A
- 200 bar working pressure, 400 bar on request
- Max working temperature 200°C
- Protection class IP65
|
|
Novafix HD2K-...GM/GK
Mechanical Flow Switch for liquids media, with spring-supported piston and magnetic triggering of a reed switch. Rugged construction in brass or stainless steel with additional viscosity compensation.
viscosity compensation 30-330mm²/s
good repeatabilty
high switch capability
hermetic separation of mechanical and electrical component
exact setting of switch via scale + gear
|
|
Maximum measurement accuracy ensures absolute safety, control and reliability in liquid handling - be it manual, automatical or computerized.
nutating disc type flowmeter. For portable use with FLUX barrel and container pumps or fixed installation into pipework. Suitable for liquids up to 2.500 mPas (cP).
|
|
PD Flow meter for additives, pharmaceuticals, aromatic substances/perfumes, liquefied gases,
demineralised water, fluid food, 2- and 3-component applications and extremely low flow rates.
Specification:
•Measuring range: 0.005...0.25 l/min
•Viscosity: 0.6...6 mm²/s
•Linearity: ±2.5 % of actual value
•Pressure: max. 100 bar
•Fluid temperature: max. 70 °C
|
|
The Titan oval gear flowmeters work by using the liquid pressure to drive a pair of interlocking oval gears. This rotation can be detected by a variety of means to give either a TTL or contact closure pulse output. The unit is manufactured in a choice of materials and pressure ratings to suit most applications and as with all positive displacement flowmeters, the performance improves with increasing viscosity, and can achieve an accuracy of ± 0.1% of reading.
The standard range of sizes covers from 0.25” to 2” BSPF connections, with maximum flows from 1l/min to 500 L/min depending on the model. Viscosities up to 10,000cP can be measured accurately, both in forward and reverse flow. Units are available for high pressure and temperature operation
|
|
Oval type flow meters are a complete flow measurement and monitoring system for re-circulating oil systems.
The method of measurement is based on the rotation of special oval designed gears – the speed of which changes in proportion to the flow of oil through the meter. This gives a visual indication of the flow rate through the transparent cover and also sends electrical pulse signals to an electronic monitor or PLC to provide actual flow figures.
This also provides information to allow either low or high flow monitoring to be provided.
Measurement is independent of viscosity and therefore a real flow will be indicated throughout the temperature range.
Pressure drop through the flow meter is relatively low.
The flow meter is designed to pass a small flow even if the gears are prevented from turning due to solid particles contained in the oil. This prevents complete starvation of oil to bearings etc.
|
|
The AT SERIES Flow Meter is ideal for measurement of harsh chemicals and liquids.
AT SERIES Positive Displacement Flowmeters can accurately measure flow rates down to 63 ml/min. Corrosion resistant materials make these sensors ideal for a wide variety of chemical flow monitoring applications.
SENSOR FEATURES
* Simple design - only two moving parts
* Low flow capability
* Measures pulsating flows
* Economical cost
* Non-metallic body & gears
* High resolution pulse output
* Low pressure drop
* Compact size
* Horizontal or vertical mounting
|
|
fuel meter
DM100 Flow Meter
DM150 Flow Meter plus Filter
The DM100 has been designed to measure diesel, kerosene and petrol, and is made from corrosion resistant aluminium with easy to read mechanical register.
Features
- oval gear design
- low pressure drop allows for gravity and pump (in-line) applications
- register cap can be easily removed and rotated to every 90° orientation for display reading
- supplied with integrated mesh strainer
- available in Litre, US Gal, UK Gal calibration
- 5 year warranty
- 10 year parts availability
|
|
Measuring the volume flow rate of liquids and liquefied gases and in loading systems in the chemical and petrochemical industry, in the mineral oil industry, in the food and beverage industry.
Oval Wheel Meter Series OV
DN 80 - 100
PN 16
flow rates 2,4 - 200 m³/h
accuracy ± 0,3 %
operating temperature according to design -10°C to 60°C
for custody transfer admitted
Oval Wheel Meter Flowal
G 1/2"
PN 16
for small flow rates 0,2 - 10 l/min
accuracy ± 1 - 2 %
operating temperature according to design -10°C to 80°C
|
|
Liquid Meters Type FMO
Oval rotor type flowmeter in 7 model sizes for flowrates of 0,1 to 350 l/min and viscosities up to 500.000 mPas (cP).
|
|
Low Volume Rotating Vane Flowmeter DPL
Low Volume Rotating Vane Flowmeter DPM
Turbine Wheel Flowmeter DRS
Low Volume Rotating Vane Flowmeter DTK
Low Volume Turbine Wheel Flowmeter SFL
Electronic Low Volume Flowmeter KFF
Micro Flow Rate Measuring Transducer LFM
Rotating Vane Flowmeter DRH
Rotating Vane Flowmeter DRG
Turbine Wheel Flowmeter DPE
Turbine Wheel Flowmeter DRB
Rotating Vane Flowmeter/- switch /- counter DF
Rotating Vane Flowmeter/- switch DFT
Paddle Wheel Flowmeter/- counter/- batcher DFB
Turbine Wheel Flowmeter / -counter EDM
High Precision Turbine Wheel Flowmeter PEL
Turbine Wheel Flowmeter TUV
Turbine Wheel Flowmeter TUR
Ring Piston Counter DRZ
Oval Gear Wheel Flowmeter OVZ
Screw-Spindle Flowmeter OME
Gear Wheel Flowmeter, aluminum KZA
Screw-Spindle Flowmeter OM..
Gear Wheel Fllwmeter DZR
Universal Indicator ADI
Digital Panel Indicators DAG
Universal Batch Controller ADI-Z
Industrial Batcher, Counter, Flowindicator DAG-AXI
Frequency Transmiter FMU
Universal Bussystem KOBUS
|
|
The Brooks® portfolio of products includes additional liquid metering and controlling devices. These products are appropriate for numerous specialized applications.
* Flomega™ liquid flow meters and controllers use thermal mass flow technology to accurately measure and control liquids and are weatherproof and certified for use in hazardous areas
* Oval Gear positive displacement meters are ideal for highly viscous liquids in applications where accuracy and repeatability are critical
|
|
|
|
|
|
Volumetric flow-meter series AM
with magnetic gear and electronic display
The am series volumetric flow-meter with oval gearwheels allow to perform precise and highly repeatable measurements, even with very vis-cous liquids, with up to 1,000,000 cps. The ease of use and compactness of these products, together with the possibility of installing and independent battery power supply, make them suitable to be fixed on fixed installations as well as transfer and distribution lines for fluids, both for mobile applications such as accessories for distribution valves and guns and for any other industrial application for the control of the delivered fluid.
CONNECTIONS: from 1/8” to 3”up to 1.000.000 cps
PRECISION: +/- 0,5%
REPEATABILITY: 0,03%
CONSTRUCTION MATERIALS:AISI316 - ALU - PPS
Two oval gearwheels are located inside the measuring body and, when pushed by the flow, they rotate in opposite directions; every gear contains two magnets which, coupled with an external sensor (reed type or hall effect sensor), transmit a pulsing signal. One of the sensors can be replaced by an analogue signal directly integrated in the electronic card. The frequency of the impulses determines the instantaneous flow rate, as every cycle corresponds to a given flow volume.
|
|
|
|
|
|
Flow measurement must be efficient, economical and, above all, suited for practical use. These demands call for a multi-functional systems that can easily be adapted to the individual requirements. Irrespective of whether the application relates to thin-bodied or viscous media, small quantities or an entire road tanker, with or without preselection - Lutz offers suitable systems for all applications
Flow meter TR:
- Turbine wheel principle
- Can be used in combination with all drum and
container pumps
- For aqueous, non flammable Medien
- Range of measurement up to 120 l/min
- Operating pressure up to 2 bar
- Housing made of PP or PVDF
- Without preselection
Flow meter TS:
- Nutating disc principle
- For mobile or stationary use
- For thin bodied to medium viscous liquids
- According to Atex 100a
- Range of measurement up to 120 l/min
- Operating pressure up to 10 bar
- Housing made of PPO, PPS or Stainless Steel
- With or without preselection
Flow meter HDO:
- Oval gear principle
- For mobile or stationary use
- For thin bodied to highly viscous liquids
- According to Atex 100a
- Range of measurement up to 350 l/min
- Operating pressure up to 55 bar
- Housing made of PPO, Aluminium or Stainless Steel
- With or without preselection
|
|
- Sizes: 1 1/2" through 6"
- Flow Rates: 5 GPM through 1,000 GPM
- End Connections: ANSI Flanged, NPT, BSPT, Slip Weld
- Pressure Ratings
- Cast Case: 150 & 350 PSI non shock working pressure
- Two Case Steel Case: 150/150, 150/275, 300/300, 300/720 PSI; 600/1440 ANSI non-shock working pressure
- Materials of Construction
- Meter Body: Aluminum, Cast Iron, Steel, Stainless Steel
- Seal Materials: Buna "N"; Viton®; Teflon®
- Accuracy:
- Mechanical Registration:
- Capable of ±0.125% over a 5:1 range
- Capable of ±0.22% over a 10:1 range
- Capable of ±0.5% over a 40:1 range
- Electronic Registration:
- Capable of ±0.10% over a 5:1 range
- Capable of ±0.10% over a 10:1 range
- Capable of ±0.15% over a 40:1 range
- Repeatability:
- Mechanical Registration: 0.05% (±0.025%) of reading over entire range
- Electronic Registration: 0.03% (±0.015%) of reading over entire range
|
|
|
|
|
|
Chemical injection fluids are normally viscous and are therefore natural applications for the VFF meter. The flowrates are relatively low and the pressure is high compared to most general industrial applications. The VFF Rotary meter is the ideal measuring element for these service requirements. Long term stability of metering and reliability is assured by the basic simplicity of design and quality of production.
VFF Meter Design & Advantages
The heart of the VFF meter is a simple but precisely made, oscillating rotor that sits freely within the rotor chamber of the meter. It is manufactured in a variety of materials. The meter principle is of 'positive displacement'. The rotor is driven 'positively' by the flow, which passes through the flowmeter in 'discrete pockets' with minimum fluid 'slippage'. This gives inherently greater accuracy than is available from axial flow turbine type meters for a low flow of a fluid more viscous than water. Each meter provides a exceptionally wide flowrange and has excellent low flow metering capability.
|
|
Only the measuring capsule needs to be replaced on expiry of the calibration period
housing and coupling head (same design as CALYGA meter) remain fitted in the pipeline
|
|
These meters are mainly used for viscous fluids for flow rates of less than 8 l/min. We specialise in low flow metering noting that the meters will return a rangeability of 1000:1 for most viscous fluids applications. Materials are 316 stainless steel with a variety of rotor materials. We can measure from 0.00016 to 1750 l/min. (and up to 4000bar)
The VFF range of meters are specificaly designed for very low flow (0.0003l/min), high pressure (2000bar) hazardous area (Ateax approved) applications. They have been in service for over 15 years in the UK North sea oil and gas industry for chemical injection applications.
|
|
|
Rotary piston gas meters have been manufactured since 1930 by Aerzener Maschinenfabrik, one of the largest and oldest manufacturers worldwide. The basis for the design of the gas meter series is from many years of experience and continual dialogue with the end users, as well as using the harmonized EU-standards which will apply to all installations within the European Market. They are manufactured in accordance wiht the Aerzen tradition for quality corresponding to the quality assurance system, certified to DIN ISO 9001 and as per pressure device guideline DGRL 97/23/EG.
|
|
|
for volume measurement of gases in various types of construction an sizes. Gas meter sizes from G 40 up to G 4000 for gas volume flow measurement from 0,65 m³/h - 6.500 m³/h. Measuring pressures up to 25 bar. Works tested or officially calibrated as per national and EU-directives.
|
|
Novafix VD-...GR
Mechanical Flow Switch for liquids or gaseous media, with contactless triggering of an adjustable reed switch.
Rugged design in brass / bronze combination.
good repeatability
dirt-resistant
exact setting of switch via scale
|
|
| ... products without technical information |
| |
|
|
Volumetric flow-meters
