|
|
|
|
|
|
Desktop-torque meter with memory and output signal for checking the opening and close torque of screw caps of bottles, glas jars, cosmetics etc.
For applications in beverage, cosmetic and pharmaceutical industry etc.
Measuring range 0 - 2.000 Nm / 5.000 Nm / 10.00 Nm
Resolution 0.001 Nm / 0.01 N
- 2 selectable modes: Real Time: to display load transients
Peak: to capture the peak force achieved during a test
- Display the opening or closing torque (clockwise and counterclockwise torque)
- 3 selectable units: Nm, kgfm, Lb.in or Ncm, kgfcm, Lb.in
- Clambs containers from Ø 20 to 180 mm (smaller Ø on request)
- Programmable high/low setpoints for go/no-go testing with color-coded indicators (orange, green, red) in the LED display and relais outputs
- Storage of 1000 values for recall:
· on the display
· for data transfer to a PC
· for printing with report
- Torque measuring unit with high internal measuring frequency
- 3 output signals: RS 232, analog, Mitutoyo Digimatic
- 2 Models: - DTX2A mains operation
- DTX2B battery and/or mains operation
- Torque meter for fast, accurate measuring
- High repeatability
- Easy to use
- Manufacturers certificate with measured values is included
|
|
DTX2 series are torque measurement system for the screw-caps of cosmetic, food and beverage containers.
The operation is very simple and it is possible to achive high repeatability and accuracy.
|
|
|
|
|
|
Mecmesin's range of manually-operated Digital Torque Testers provide a simple and cost effective method of measuring low-level torques.
From packaging and toys, to high-tech automotive controls and medical devices, Mecmesin testers can help assesses the quality and usability of any rotating component.
Orbis
Perfect for any small rotary component, this rugged, lightweight and portable tester is ideally suited to both laboratory and production environments. The versatile mounting table sits atop an integrated digital torque sensor and grips the base of your sample.
The tester features high sampling-rate electronics for accurate peak torque capture, offering a greater level of accuracy than mechanical spring-type testers.
Summary.
Clockwise & Counter-clockwise Digital Torque Capture
Compact, Portable & Affordable
Clear Digital Display & Intuitive Controls
6N.m (50 lbf.in) Capacity
Water Resistant (rated to IP54)
Data Output for Easy Export of Results
Mains or Battery Powered
Versatile Mounting Table
Graphical interrogation of results with Dataplot Software.
Tornado
The Tornado features the same basic design and functionality as the Orbis tester, but with a range of advanced features, including pass/fail alerting, on board memory and a tamper-evident closure testing facility. The Tornado is also available in a range of capacities from 1.5N.m to 10Nm.
Tornado features.
Range of Capacities; 1.5N.m (13lbf.in), 3N.m (26lbf.in), 6N.m (50lbf.in), 10N.m (90lbf.in)
On-board Memory; up to 500 readings
Audible/Visual Tolerance Alerting
Tamper-evident Closure Testing; Characterise Both'Slip'& 'Bridge'Torques
|
|
Features:
- Dull Tool Detection
- Broken Tool Detection
- Grinder Gap Elimination
- Tool Touching Workpiece
- Misplaced Workpiece Detection
- Overload Protection
- Crash Avoidance
- Wear Compensation
|
|
|
|
|
|
FEATURES
The LMTX is a new system for the monitoring of hook load for telescopic cranes also when mechanical extensions are used. The system is composed by a transmission unit LIM-TX, which is hanged on crane hook, and by a receiver unit LIM-RX positioned in the control panel unit.
The LIM-TX is composed by a strain gauge pin for load detecting and by a micro controlled transmitter to send by radio the data weight to the receiver unit.
The new structure of the shackle hook group does not limit the lifting operations.
The unit LIM-RX has two functions: the show of the data weight through a four digits red display, the load limits control.
If used with mechanical extensions (up to four jibs) the LIM-RX allows, through a push button, to set the numbers of jibs and consequently to control the overload limits by a relay contact and a LED indication.
The device is included in SRD (Short Range Device) classification and uses a frequency band of 868.3 Mhz of free use (without any authorization).
The LIM-TX unit works with a battery rechargeable by the truck lighter and the LIM-RX unit works by a 12..24 voltage battery.
Free maintenance. No interference with the other on board radio devices.
APPLICATIONS
Load monitoring
Overload monitoring
|
|
It is the force measuring instrument of the mechanical type of the power supply needlessness which can measure tension and compression force easily and correctly.
Based on our long history of technical achievement as a force gauge pioneer with the variety of know-how, IMADA mechanical force gauge is produced under advanced technology and severe quality control, and maintain early high precision for a long period of time.
|
|
Real time or Peak Hold Switch to observe transcients or capture peaks by a drag indicator
- Zeroing by a short push of the switch
- Tare Ring for an easy calibration of the tester
- Dual Scale: Shows NEWTON and kg
- Can be mounted on all manual test stands or the optional handle
|
|
|
The OBR 4400 takes the industry's first ultra-high resolution OTDR with backscatter-level sensitivity designed for component- and module-level reflectometry to the next level. With a small, easily transportable platform, the capability to "see" reflections out to 2 kilometers with no dead zone, and integrated temperature and strain sensing, the OBR 4400 gives you the ultimate in fiber diagnostics. The OBR 4400 uses swept-wavelength coherent interferometry to measure minute reflections (< 0.0003 parts per billion) in an optical system as a function of length with spatial resolution less than 50 microns. This provides the user with precision reflectometry and unprecedented optical-module inspection and diagnostic capabilities by providing the ability to locate and troubleshoot splices, connectors, fiber bends and breaks, insertion loss points, track polarization, verify PM components and more.
|
|
|
|
|
|
Functionality, accuracy, and precision formerly reserved for expensive and complex material testing equipment are now available with Andilog Force Gauges. The functionality of material testers previously reserved for research or development applications are now available to the production floor with the introduction of the Centor Touch Force Gauge.
High accuracy of 0.1%, sample measurement rates up to 5000 Hz, internal memory, measuring peaks and graphical display are just the beginning features. Centor Touch can provide break force, average, curve force versus time or deflection, statistical calculations and real time pass/fail analysis based on user supplied tolerances. Data logging and communication to your computer or network is available with RS232 or USB ports. Centor Touch is designed for manufacturing environments, providing performance and easy operations to use and understand with the addition of the new, colored touch screen technology. Icons guide the operator in the selection of the appropriate measurement technique and method for their application. Setup menus, prompts and results are available in multiple languages.
When integrated in manufacturing processes, the Centor Touch can communicate with controllers through fast TTL outputs.
With the combined features of functionality, flexibility and simplicity, the Centor Touch is the solution for more sophisticated and economically feasible testing solutions for the factory floor.
|
|
TesT develops and validates systems, in line with the constantly growing requirements and aim at the needs of its customers to guarantee a complete and competent solution of the highest level. We engage ourselves to reach a high customer satisfaction in a surrounding field of prevention and continuous improvement. The new model 322 is the High end product of most modern measur-ing technique and offers an unusual price performance ratio.
dynamometers integrate a high-resolution force sensor as well as processor-controlled electronics with most modern software, based on a wide experience and the requirements of our customers.
The main area of application for these devices is research and development, production and quality assurance. Particularly operating forces as well as stability of construction and functional units will be measured.
Examples
Springs, switches, levers, fasteners, precision mechanics, foods, cosmetics, vehicles, medical technology, and many more.
|
|
|
|
|
|
RON portable digital scales include the Crane Scale, Dynamometer Load Cell and Overload Detector series.
The low headroom RON 1000 Standard Type Overload Detector is designed to be installed on the dead end or can be used between the hoist and its trolley.
RON 1000 Standard Type is a low headroom, electromechanical Overload Detector, used for overload monitoring. It may be configured to trigger any desired electrical alarm supplied by the customer, including stopping the lift when an unsafe overload condition occurs, for overload detection and prevention.
Overload during lifting: Hoist or crane overload is dangerous and can cause accidents. Overload monitoring is important for prevention of crane overload.
The devices are supplied factory-calibrated and ready for installation. Available in a wide variety of capacities, the RON 1000 can be supplied in capacities ranging from 500 lbs (250 kgs) to 20,000 lbs (10,000 kgs). Each unit is initially adjusted to give the user an overload indication at 105% of rated capacity. Additional detection point is optional.
RON portable digital scales: Crane Scale, Dynamometer and Overload Detector series are factory-tested and supplied with a test certificate, including a fully traceable calibration chart.
|
|
Simple and yet complete, the CENTOR First uses efficient technology to simplify force measurements, in tension and compression.
A big display shows the force measured in tension or compression in the unit selected by the operator: newtons, kilograms or pounds. The bar graph completes the measurement.
The 3 keys make it very easy to use this force gauge and access the essential functions: measurement of the peak tension or compression value, resetting to
zero, and changing the measuring units. It is an ideal tool for basic tests during production. Its metal casing, protected by an elastomer overmould, gives it
exceptional strength.
The internal sensor stands up to an overload of 200% of its maximum capacity.
Simple, precise, robust, supplied with its own carrying case, mains adaptor and certificate, ready for use, it is the basic tool for force measurement.
|
|
|
|
|
|
Measuring System PHYSIMETER® 906 MC-B
The measuring system PHYSIMETER® 906 MC-B has been designed for the determination of the mechanical parameters force or torque on the basis of wire strain gauges. The instrument can be supplied with an integrated or an external sensor. For the power supply a block battery of 9 V is required (standard article) or alternatively a plug-in power pack (option). For easy handling the instrument is provided with the functions On/Off, reset and indication of peak value (upper and lower measuring value). In the standard version of the instrument the load introduction takes place at the bottom. Upon request, the load introduction can also be effected on the top of the instrument. The ergonomically designed housing, made of anodised, high-strength aluminium, is provided with threaded bores at the front side so that an unproblematic connection to the ERICHSEN testing machines is guaranteed - as it was also ensured when using the preceding models of the tensile and pressure testing instruments. The instrument is perfectly suitable for mobile as well as for stationary applications.
|
|
|
|
|
|
Using the Centor technology, the Centor W Easy TW digital torque gauges have a very large graphic display and show a maximum amount of information for more efficient measuring: they show the current reading and the peak value at the same time, and a bar graph to show the operator whether they are close to their maximum capacity. If necessary, the backlighting can be used to further enhance reading comfort.
Mounted with a non removable wrench torque sensor, it allows you to measure very big torques with easily without too much force. Ideal to check the bolts, tools, screw ... in production or quality with accuracy. Its advanced measurement chain enables it to use a sampling rate of 1,000 Hertz with a resolution of 1/10,000 FS and a total error of less than 0.5% FS.
Many other functions complete the possibilities of the gauge:
- the Set point functions can be used to carry out “OK, NOK” tests: a symbol appears on the display.
- The fully programmable RS232 output sends the data to a PC.
- A digimatic output can be used with Mitutoyo statistical printers.
|
|
|
TorqueStar Opta is the equipment of choice for the measurement and collection of torque data in the manufacturing environment. TorqueStar Opta's range of software features can be individually specified to give a configuration most suited to the requirement, from a simple no-frills readout to a comprehensive audit tool with display of torque curves and specialist measurement routines.
|
|
- Ergonomically-designed and advanced style.
- Rugged die-cast aluminum housing excellent for noise protection.
- Various output functions (For models with the functions only).
- Peak-hold function for all models.
- Various functions unique to the digital gauges.
- Various attachments and a carrying case.
|
|
The E100 SBT Series Strain Gauge Base Mounted Transducer has a substantial easily mounted body, which houses the shaft and strain gauge assembly. The shaft is mounted on its outer end in a ball race, ensuring accurate torque measurement. A chuck accommodates simple adapters which can be supplied with standard square dimensions, or machined to suit specific applications.
|
|
Torque wrench calibrator
CENTOR Meter W
The CENTOR Meter W torque wrench calibrator enables verification of torque wrenches thanks to a series of reference sensors ranging from 22 to 222 NM.
Torque wrench calibrator
torque screwdriver calibrator
CENTOR Meter H
A set of low-capacity reference torque sensors enables use of the CENTOR Meter H torque screwdriver calibrator to verify torque screwdrivers from 1 Nm to 6 Nm.
|
|
Atlas Copco provides a complete line of products for measuring torque, angle, pulses and speed within all types of assembly industry.
Portable analysers:
The ACTA 4000 enables you to perform a full range of functions, from simple torque checks to advanced graphic tightening analysis. It comes in different models to cover all your needs, and is upgradeable. The ACTA 4000 together with the Tools Talk QAT software, is the user friendly complete quality management system! The system will automatically give you information when the tools are due for calibration. Quality management has never been easier!
Benches:
The JSB Light Joint Simulator Bench can easily be moved along the assembly line. This enables you to test your tools under actual conditions, with the right hose length and air pressure. The hydraulic brake
on the bench can be set to simulate actual joint stiffness. The JSB Light provides maximum flexibility and accuracy.
|
|
|
|
|
|
Norbar's Test Beams are designed for the static calibration of Torque Transducers. They are ideally suited to Norbar's transducers, but can be employed on other manufacturer's equipment.
Torque is generated by the application of a known force at a known radius from the centre of rotation of the torque transducer.
Designed to remove potential sources of measurement error, these beams can be used to calibrate Norbar torque transducers, and torque transducers from other manufacturers (where design permits), as well as mechanical test devices. UKAS length certification is provided with each beam.
The Beams are designed with square drives machined to the top limit of ISO 2725:1987. This minimises any play between the beam and the transducer. However, a combination of square drive tolerances, misalignment of fittings and elastic rotation of the transducer shaft inevitably cause the beam to rotate from the horizontal under load.
Norbar's Radius Ended Beams are designed with a /-8% degree usable arc within which the calibration accuracy is unaffected.
Additionally the beams are designed to apply load on a vertical plane which cuts through the square drive inside the transducer. This minimises bending moments on the transducer and, for safe operation, ensures that the beam will not fall out of the transducer.
|
|
|
|
|
|
Experienced fastening tool users know that frequent calibration of air and DC electric tools is necessary to ensure exceptional performance. Ingersoll Rand offers users its Expert range of torque analysis systems. The ETT tabletop torque testers provide torque coverage for fastening tools (including pulse tools) from 1 to 30 Nm, while the ETA series of torque analyzers provide portable measurement capability with the ability to use external transducers or joint simulators. The ETW-A audit wrenches offer a portable and extremely precise way to audit actual joints following tightening with a traditional tool. And finally, Ingersoll Rand's new ETW-E provides labs and low-volume assembly operations the ability to fasten with true closed-loop control in a handheld cordless tool.
For users who don't have the capability or facilities to perform their own tool calibration, Ingersoll Rand also offers calibration service for any and all brands of fastening products. Call our toll-free number at the top of this page for details.
|
|
Besides having all the functionalities of the CENTORW Easy, the CENTOR W Star torque gauge provides handy further possibilities: the graphic display shows the
full graph Torque = C(t). This gives you a general overview of the current test.
The torque gauge is able to make several types of calculations on demand (break point, first peak, average, torque at time T, etc.).
It is equipped with a special sensor recognition system. This means that a single instrument can read different sensors (several capacities, Force
or Torque).
Furthermore, it is possible to freeze its configuration to avoid handling errors.
It is the most versatile instrument designed for all tests in industrial surroundings.
|
|
|
The DRBT-100 bench mount torque tester has a wide torque measurement range and come complete with two spring rundown joints and a protective carrying case. The tester can store 800 data points and allows the user to enter high / low torque limits for Good/NG indication during testing. Built-in statistical calculations allow the user to review min, max, and average values for a series of up to 30 torque readings.
|
|
The MTA is a hand-held Torque/Angle Analyser suitable with all our transducers (NST, B and SB models). Easy to start and use it offers tool testing, graphing capabilities and a graphical menu for easy navigation.
The MTA allows you to set up and create tool tests and save the readings so that you can export the data to a PC for documentation.
It’s the ideal solution for organizing and storing test data for ISO and SPC documentation.
|
|
This newly designed, numerical control torquemefer is capable of carrying out right-hand and left-hand torsion tests including at break.
It can be mounted till three different torque-celles always mounted and ready to work.
It is a freestanding structure with precision ball-type guides.
It is supplied with a computer and touch screen with new 24-bit microcontroller. Our system uses severo/ cards to control the axes, sensor, and cells that are connected via CanBus to enable displacements to position or force at a feedback speed of 1000 Hz. Load cell reads are effected 1,000 times per second. Minimum indexing is 1/32,700 (this can be increased on request).
|
|
|
|
|
|
Hand-held torque meter with separate sensor for measuring the torque of screws, components, screw and plug connectors, drive shafts etc.
Mains and battery operation with memory and output signal
Measuring range 0 - 0.5 Nm/2.000 Nm/5.000 Nm/10.00 Nm
Resolution 0.001 Nm/0.01 Nm
- Two selectable modes: Real Time: to display load transients
Peak Modes: to capture the peak force achieved during a test
- Display of opening or close torque (clockwise and counterclockwise torque)
- 3 selectable units: Nm, kgfm, lb.in or Ncm, kgfcm, lb.in
- Programmable high/low setpoints for go/no-go testing with color-coded indicators (orange, green, red) in the LED display and relais outputs
- Storage of 1000 values for recall:
· on the display
· for data transfer to PC
· for printing with report
- torque meter with high internal Sampling rate
- 3 output signals: RS232, analog and Mitutoyo Digimatic
- 4 different torque sensors available
- The torque sensors of models HTG2-10 and HTG2-10 NC includes an additional supporting handle for better operation
- Torque measuring unti for fast, accurate measuring
- High repeatability
- Easy to use
- Manufacturer`s certificate with measured values is included
|
|
It is a torque checker to control electric screwdriver, air driver, and torque driver.
The measuring joints included with I-8 series and never like as ordinary screwed ones but brings you a stable measurement by its low friction. Needlessness to rewind the joint helps you to saves a lot of time.
|
|
Verify torque settings and repeatability of hand tools, power tools, and pulse tools.
Features:
Dual transducers for testing a broader range of torque
Three modes of processing torque signals:
1. Peak: records & displays highest torque peak
2. First Peak: records & displays first torque peak
3. Track: displays all torsional strain applied to transducer in real time
|
|
BalTec (UK) Ltd can offer a wide range of torque measuring equipment, from 0.1 Nm to 200 Nm, especially designed for easy calibration of your tightening tools along the assembly line or in the laboratory.
Doga torque equipment will improve your manufacturing quality and is suitable with screwdrivers and torque wrenches.
Model EZ20 Torque Tester
- Measuring range 0.1Nm - 20Nm.
- Accuracy +/- 0.5%.
- 500 measuring memories.
- Manual and auto reset.
- RS232 output for PC transfer.
- Mini/OK/maxi torque limits.
- Peak - first peak - track signals
|
|
CS1 series offers variable models with full scale of +/- 10 Nm à +/- 2000 Nm
* Easy to install
* Sensitivity ± 1.5 mV/V
* Reapetability ± 0.1 %
* Linearity and hysteresis ± 0.25 %
* Fixing by threadings
* Protection IP54 or IP67
Applications :
* Measure of static couple
* Screw drivers tools.
|
|
|
|
Force measurement instruments, Torque measurement instruments
