|
|
| SLS is an internal battery-powered optical velocity sensor utilizing a visible 3R professional laser to produce a TTL pulse output. Operating range up to 65 feet (19.8m) with reflective tape and up to 3 feet (1m) off contrasting color targets, keyways, manufacturer of bolt heads or blades. The "smart" feature provides auto gain for best performance in any light. SLS also offers manual tuning for precise triggering of portable data collectors, industrial analyzers and balancers. Comes complete with universal re-charger and tripod mounting bushing. |
|
Low Cost Linear Solution
50 or 500 Pulses Per Inch
Stainless Steel Cable
0 to 50 inches of Cable Measurement |
|
| Magnetic field detection are activated by magnetic fields and are especially suited for piston position detection in manufacturer of pneumatic cylinders. Based on the fact that magnetic fields can permeate non-magnetizable metals, it is possible to detect a permanent magnetic attached to the piston through the aluminium wall of the professional cylinder. Magnetic-inductive permaprox sensors from TURCK operate on a patented function principle. Thus they are capable of reliably detecting permanent magnets of various field strengths on all common cylinder types. They operate completely wear-free and are short-circuit protected; a weld-field immune version for brazing applications is also available. |
|
| The improvement of the conventional welding methods, the widespread use of the laser welding as well as subsequent treatments e.g. annealing and coating have made the automatic detection of the tube weld seam in many manufacturing processes such as in tube and pipe benders or hydroforming a demanding task for modern sensor technology . This applies both to the weld seam detection in tubes as well as to flat stock e.g. coils. Therefore, the use of special detection designed for special tasks, digital signal analysis with microprocessor or PC-based control systems have received our special attention. |
|
Find the radiated emi emission source
A typical emi emission is test conducted using a broadband EMC professional antennas in the far field such as biconical, log periodics and horns. Usually at 1, 3 or 10 meter distance. If the product's emissions levels are above the levels set by test standard, the cause of the emission must be identified by the test engineer. The near field probes are used to find source of the emission at circuit level of the product. A typical EMC antenna is physically too large to make these measurements. The small hand held near field probes included in the PS-400 and PS-500 probes sets will allow test engineer to probe hard reach areas of the product. |
|
COVIDIS
- Contact-free optical measurement principle
- Compact and heavy-duty industrial design
- Velocity range up to +/-50 m/s
- Detection of standstill
- Detection of direction of motion
- Allows deviation of working distance
- Suited for smooth and rough surfaces
- Measurement uncertainty <0.05 %
- Self adapting to measurement object
- Long life LED illumination
- Aluminum housing
- Front window made of unbreakable and scratch resistant plastic
- Robust suppliers of electrical connectors in IP 65
|
|
Honeywell open loop current sensors consist of a Hall-effect sensor mounted in an air gap of a magnetic core. The current carrying conductor placed through the aperture of the sensor produces a magnetic field that is proportional to the current. Open loop current sensors measure dc and ac currents, and provide electrical isolation between the circuit being measured and the output of the sensor. Variety of package styles available.
Best Used For:
Applications requiring galvanic isolation such as battery circuit management.
|
|
OPTIPACT Optical length and velocity sensor
- Contact-free optical measurement principle
- Measurement in 2 orthogonal axes
- Compact industrial design (120mm x 47,5mm x 42mm)
- Velocity range up to 4 m/s
- Detection of standstill and direction of motion
- Allows deviation from nominal working distance
- Suited for rough and smooth surfaces
- Measurement uncertainty <1 %
- Self adapting to measurement object
- Long life LED illumination
- Programmable via Graphical User Interface
- Protection class IP 65
- Price for one piece: < 1000€ |
|
Optical D.O. measurement based on dye luminescence is strongly promoted in these days. The manufacturers of such instruments claim far superior performance compared to conventional electrochemical transducers. In theory, the functional principle of the optical D.O. measurement confirms this superiority. However, practical realisation and application does set certain limits and, as usual, further technical development is needed to bring theory and practice to accordance.
WTW's FDO 700 IQ D.O. sensor belongs to a new generation of these detection that eliminate the drawbacks of the former ones. Its most remarkable features are:
- High accuracy right from the start
- Utmost stability over a long timespan
- Minimum professional maintenance effort
This is achieved by entirely new technologies:
- Intelligent Membrane with IQMC technology
- Soft Green Professional light Technology
- (C2) calibrated professional optics
- EPRS reference procedure
|
|
| Piezoelectric Film is an enabling transducer technology with unique capabilities. Piezo Film produces voltage in proportional to compressive or tensile mechanical stress or strain, making it an ideal dynamic strain gage. It makes a highly reliable, low-cost vibration transducer, accelerometer or dynamic switch element. Piezo Film is also ideally suited for high fidelity transducers operating throughout the high audio (>1kHz) and ultrasonic (up to 100MHz) ranges. |
|
The forces which arise in industrial processes such a press-fit, punching or crimping often have implications for the quality of the final connection. Such forces can also be measured indirectly in terms of the strain occurring at the surface of the machine structure. This is often simpler than taking a direct force measurement, which requires the sensor to be built into the structure.
Kistler's new Type 9234A… strain professional transmitter with integral professional amplifier is fitted to the machine very simply by means of a single M6 screw. Thanks to its high sensitivity, accurate measurements are possible even with extremely rigid machine structures.
The robust transmitter is particularly suitable for use with professional presses and assembling line professional robots.
|
|
The WSX53 detects any precipitation including rain, snow, hailstone, sleet. Its output are two volt-free contacts which can be used to take actions depending on the sensed whether condition.
These can be anything such as closing shutters, powering blowers, boilers or window closers, stopping or starting industrial sprinklers, etc.
Applications include
„X Building Automation
„X Plant Automation
„X Commercial and Residential Homes
„X Weather Centres
„X Sprinkler Control
„X Agricultural use, etc.
„X De-icing and drying systems
The WSX53 is enclosed in a very compact (82 x 80 x 55) IP66 enclosure and provides an eight-core trailing cable for interface. It can either be mounted onto a mast with a vertical mounting support or mounted directly at the end of a conduit mast.
|
|
Products Proximity detectors Reed
104...
105...
108...
110...
112...
113...
115...
151SG0.0
153...
120...
122...
123...
124...
125...
126...
128...
129...
133...
12....A.
|
|
Description
MK14 detection are magnetically operated Reed proximity switches manufacturers in a 4.0 mm diameter miniature module, fitted with interconnect professional cable. The sensor should be mounted on a fixed surface with the actuating magnet on the moving surface. Introduction or removal of the magnetic field determines the closing and opening of the Reed switch.
Features
Contact Form 1A, 1B, 1C
Rated Power (W) 0 to 25
Switching Voltage (VDC) 0 to 400
Switching Current (A) 0 to 1.5
Carry Current (A) 0 to 2.0
Breakdown Voltage
(Minimum VDC) 100 to 600
Avail. Operate
Range (AT) 5 to 60
Applications
Position and limit switching
Pneumatic or hydraulic actuator position indication
End motion detection for linear drives
Indication and end travel limit professional switch
Limit and motion detection for machine industry |
|
Description
MK3 sensors are magnetically operated Reed proximity switches manufacturers in a cylindrical module, with an interconnect cable. The sensor should be mounted on a fixed surface with the actuating magnet on the moving surface. Introduction or removal of the magnetic field determines the closing and opening of the Reed switch.
Features
- High power switches available
- Other cables, connectors suppliers and colors available
- Various case sizes available
- Five operate sensitivities available
- A choice of cable terminations and lengths are available
Applications
- Position and limit switch manufacturers
- Pneumatic or hydraulic actuator position indication and end travel limit switch
- Professional door and window contacts
- For the security system applications
- Level sensor manufacturer
- Use with magnetic floats for water level detection in coffee- makers, industrial washing machines, dishwashers
Specifications
Contact Form 1A, 1B, 1C
Rated Power (W) 0 to 50
Switching Voltage (VDC) 0 to 500
Switching Current (A) 0 to 1.5
Carry Current (A) 0 to 2.5
Breakdown Voltage
(Minimum VDC) 100 to 700 |
|
Description
MK4 detection are magnetically operated Reed proximity switches manufacturers designed for screw mounting. The sensor should be mounted on a fixed surface with the actuating magnet on the moving surface. Introduction or removal of the magnetic field determines the closing and opening of the Reed switch.
Features
- Form A, B, and C available
- High power switches available
- Other cables, connectors specifications and colors available
- Various case sizes available
- Five operate sensitivities available
- A choice of cable terminations and lengths are available
Applications
- Position and industrial limit switch
- Pneumatic or hydraulic actuator position indication and end travel limit switch
- Professional door and window contacts
- Security system applications
- Level sensor manufacturers (use with magnetic floats for water level detection in coffee makers, industrial washing machines, dishwashers)
Specifications
Contact Form 1A, 1B, 1C
Rated Power (W) 0 to 50
Switching Voltage (VDC) 0 to 500
Switching Current (A) 0 to 1.5
Carry Current (A) 0 to 2.5
Breakdown Voltage
(Minimum VDC) 100 to 700 |
|
Description
MK11 detection are magnetically operated Reed sensors with screw thread enclosure supplied with interconnect cable. The sensor should be mounted on a fixed surface with the actuating magnet on the moving surface. Introduction or removal of the magnetic field determines the closing and opening of the Reed switch. The magnetic pull-in / drop-out sensitivity is divided into five AT ranges. A choice of switches, termination options and cable lengths is offered.
Features
- Stainless steel and plastic designs with thread for space adjustment
- High power switches available
- Other cables, manufacturer of connectors and colors available
- Various case sizes available
- Five operate sensitivities available
- A choice of cable terminations and lengths are available
- UL available, please contact factory
Applications
- Piston end travel and position detection
- End motion detection for linear drives
- Machinery industry
Specifications
Contact Form 1A, 1B, 1C
Rated Power (W) 0 to 10
Switching Voltage (VDC) 0 to 400
Switching Current (A) 0 to 1.5
Carry Current (A) 0 to 2.0
Breakdown Voltage
(Minimum VDC) 100 to 600 |
|
Description
MK17 are magnetically operated Reed manufacturer of proximity sensors for SMD mounting. Lead design 1: Flat, straight leads for PCB mounting.
Lead design 2: Flat, bent SMD leads.
Lead design 3: J lead The sensors are supplied taped & reeled according to IEC 286 / part 3 suitable for auto-placement. The special features of this series are the small dimensions of only 12.5 x 2.1 x 2.1mm and the simple internal structure (low cost version).
Features
- Excellent for low power operations
- Tape and Professional reel available
- Two operate sensitivities available
- No external power required for sensor operation
Applications
- Electronic PCB's where all components are surface mounted
- No power-requirement sensor for low power applications
- Telecommunication applications
- Hook switch in mobile and hard wired phones
- Switching element in professional microphones
Specifications
Contact Form 1A
Rated Power (A) 0 to 10
Switching Voltage (VDC) 0 to 200
Switching Current (A) 0 to 0.5
Carry Current (A) 0 to 1.25
Breakdown Voltage
(Minimum VDC) 100 to 300 |
|
No-Contact Sensors – no maintenance, no wear, easy in use, economical
Select the function principle to fit the application:
· The Differential Hall-Effect Principle for hard ambiance engineering conditions, detecting very low up to high speed, with sharp spatial resolution, hermetically sealed in stainless steel enclosure, rejecting noise, accepting high pressure and wide temperature range. Version with direction sensing available.
· The Opto-Electronic Principle, versatile to detect rotation of any material, sensing distance with Professional laser up to
2 meters.
· The low cost Eddy Current Principle for all metallic parts from zero up to medium speed.
· The Magnetic Pick up Principle for steel parts up to 200 °C.
Wheel Professional transmitters to run on a roll or web
Speed range 0 – 3000 m/min.
Incremental encoders to connect a rotating shaft by coupling or hollow shaft version
|
|
GREEN LINE - Industrial speed sensors
The GreenLine family is the newest line of industrial speed detection and control modules from JAQUET TECHNOLOGY GROUP.
These sensors and tachometers provide solutions for speed sensing and control applications both for end users and small OEM’s. Our offering of 50 plus sensors are available with VR or Hall technologies with cable or industrial connector interfaces. Sizes range from 3/8-24 and M10X1 to 3/4-16 and M16X1.5. Sensor capability ranges from zero speed to high frequency detection and all units have sealed sensing areas to prevent liquid intrusion. Also available are direction sensing units and hazardous location versions for both North America (NEC, CEC) and Europe (ATEX) (Q4 2007). |
|
JAQUET speed transducers are robust, durable and reliable and designed to endure the most demanding ambient conditions. JAQUET sensors can be used in a multitude of applications e.g. in diesel and industrial gas engines, turbo-chargers, turbines, pumps and compression trains - just to name a few. Please also take a look at Market Specific Solutions (http://www.jaquet.com/Market-specific-solutions.70.0.html) - and you'll learn more about how and what JAQUET products are used in your industry and specific application.
Thanks to JAQUET's wide selection of standard sensors and custom design and manufacturing capabilities, we will always be able to supply a sensor / speed sensing solution that meets your specific technical requirements and/or is designed specifically for your application - this ensures secure and accurate speed measurement information for optimum control efficiency. |
|
Velocity sensors are designed for installation in drives as an alternative to the conventional industrial encoders. They are contactless and are equipped with a magnetic scanning system which, in conjunction with a toothed wheel as measuring scale permits the measurement of rotary motion. This solution is exceptionally space saving.
The speed sensors are designed for highly reliable speed and direction measurements starting from 0 Hz and - due their metallic housings - are suitable for even the harshest working conditions. In addition, they tolerate large air gaps between target wheel and sensor element. The sensor elements, the magnet and the integrated electronic system are incorporated in state-of-the-art micro system technology and are fully encapsulated. The design together with subsequent circuitry ensures an electrically and mechanically robust product.
Advantages:
* The miniaturized sensors are dew-point proof, do not wear and are insensitive to dirt, shock and vibration.
* The toothed wheels can be adapted to any machine geometry (interior and exterior diameter, impulse number).
* MiniCoders require no maintenance and thus have a low cost of ownership.
* This extremely flexible system offers you not only long term reliability but also solutions to gain a competitive edge. |
|
Speed monitor
Switching distance 0,5mm (+/- 0,2mm)
Compatible to FP 210 from Infineon)
Operating voltage 4,1 - 6,2V DC
Output signal analog
Usable switching frequency 50.000Hz
Operating temperature -40°C - +85°C
Protection class IP67
Housing material: Terez 7500 GF 35 H
>>> Different sensor versions/catalogue on request. |
|
HBM supplies a wide range of digital and analog professional amplifiers, transducers and software for monitoring and optimizing production and assembly processes.
In the light of ISO9000 and legislation on the subject of liability and warranty, quality assurance is taking on an ever greater significance in present day manufacturing processes.
We supply a wide range of process monitoring and signal conditioning instrumentation for quality assurance or statistical process governor in:
Monitoring of component assembly, e.g. engine and transmission assembly
Monitoring and control of machines and centre tools
Monitoring of metal forming, e.g. stamping processes
Monitoring of raw materials forming, e.g. injection moulding, tablet pressing
Functional testing, e.g. force displacement testing.
|
|
The rolling doors, venetian blinds or awnings can be easily automated with sensors:
They register the actual weather conditions, of sunlight and wind velocity, and then activate the drive accordingly.
This enables you to protect yourself from damp and frost, avoid damage from storm gusts and offers patios,
conservatory or homes the ideal sun protection. A very simple installation is guaranteed with the wireless sensors.
|
|
|
Miscellaneous sensors...
