|
|
The TCIC is Low cost high speed 8 channels thermocouple specifications measurement interface board with USB and RS-232/485 interface. The TCIC supports thermocouple types J,K,E,R,S,T or ±500 millivolts at 1 microvolt resolution.
Main features:
On board cold junction compensation
On board temperature conversion functions enable stand-alone operation
USB interface as standard or USB + RS-232 /RS-485 (option)
Multiple boards may be connected via USB or RS485
8 opto-isolated outputs configurable as setpoints, latching alarms or user outputs
Comes with very useful software package and data logger
|
|
Autoclave manufacturer Chamber/Load Probe (SL160) Sensor :
The SL160 series of autoclave chamber/load probe sensors are similar to the SL150 series, but differ in having a 90° bend and a chisel point to allow penetration of the product bottle industrial seal.
When mounting a load probe with a straight sheath into a product bottle/container in an autoclave it is often difficult to achieve the desirable orientation. This is often due to both the weight of the probe lead wire and its restrictive bending radius. The SL160 is designed to circumvent this by having a 90° bend in the probe sheath. The addition of a chisel point at the probe tip also allows it to be inserted with relative ease through the bottle seal it there is one.
The SL160 chamber/load probes are currently being fitted as original equipment by a major autoclave manufacturer. |
|
WDB Series Bearing sensors
PTC Thermistor with fixed pre-set trip points from 50°C to 120°C
NTC Thermistor for continuous measurement up to 110°C
Long term reliability
Easy installation - replaces existing grease nipple
Extensive range of PTC sensors available from 50°C to 120°
For use with T400, T400 Elite, T500 Elite or Watchdog Elite control modules
|
|
| Conax Buffalo Miniature bearing Sensors are designed to monitor temperature of embedded bearings suppliers critical to machine performance. They are available with 100Ω platinum RTD sensors, 0.00385 Ω/Ω/ºC, in 2-, 3- and 4-wire single element configurations, with operating temperatures to +250º F (+120º C) Conax Buffalo also supplies a bearing detection wire industrial seal to prevent oil migrating along the sensor lead. |
|
Install miniature sensors in or beneath the babbitt layer of industrial bearing industrial shoes. They monitor metal temperature — the most reliable indicator of bearing condition — to give early warning of oil film breakdown. Machines can then be shut down and the problem corrected before catastrophic failure occurs.
While no larger than many bare ceramic elements, these RTDs have metal cases and insulated leads to withstand rough handling and harsh environments. They’re easy to install in drilled holes for general purpose sensing.
|
|
A critical indication of the status of bearings manufacturers on large rotating plant is provided by their running temperature.
Monitoring bearings in this manner provides the ability to recognise any possible upward trend in bearing temperature. This in turn allows for a regime of planned preventative maintainance to be put in place, offsetting the possibility of catastrophic plant failure.
Due to its small physical size the small bearing sensor can be positioned close to the bearing surface allowing it to sense any early change in temperature.
These devices are available in both thermocouple and PT100 resistance thermometer format and can be supplied as either single or duplex sensors. The sensor lead wire insulation is in PTFE or glass fibre and lead wire jackets can be protected with stainless steel outer braid. |
|
Humdity- and Humidity-and Industrial temperature transmitters for use in air-conditioning systems, building services management systems and ventilation technology. Use of capacitive humidity sensors is a guarantee of high long term stability, resistance to dew formation, small hysteresis and good dynamic performance.
In this product group Galltec+Mela offers industrial transmitters, specially adapted to the needs of the ventilation and air-conditioning sector but as well standard transmitters for all applications where air humidity and temperature has to be monitored. For more difiicult applications we offer our transmitters for industrial use.
|
|
%RH, °C/°F, °C td/°F td, g/kg, g/m3, °C/°F wet industrial bulb
•Application: Drying processes, cleanrooms, critical air conditioning applications
•Accuracy up to ±1 %RH
•Probe and sensor heat-proof up to 180 °C
•Convenient operating menu (with optional display), exterior operation buttons
•Special solution hygrotest 650 HP for high humidity applications
|
|
Combined Niveau-und thermometric bulb made of high-grade steel:
Remarks:
- Level 4-20mA and temperature 4-20mA
- Level float switch manufacturers with integrated thermal relay
- Level 4-20mA with integrated thermal relay
- Level float switch with integrated PT100
- Level 4-20mA with integrated PT100 |
|
"Nivotemp 63 K + KN, 63 K-VA + KN-VA
Modern production facilities employ more and more plant automation systems and computerized controls. These allow the monitoring and control of hydraulic and lubricating systems. Traditional level controls are focused on pump protection i. e. a typical system is equipped with a level switching with one or two contacts. These contacts protect the pump from running dry in the event of leakage..
Modern systems provide the opportunity for a pro-active leakage control by the use of continuous signals.
An analog output of 4-20 mA signals continuous signals the fluid level. Deviations from the ""normal"" are detected instantly and can be transformed into many types of action. In case of a catastrophic failure such as a burst hose the pump could be shut down immediately rather then let it run until the traditional switch turns it off after a large volume of oil has spilt.
The Nivotemp 63 versions provide continuous analog signals for liquid level only or for level and temperature combined. They are available in two standard length or in 150mm increments. The flange dimensions are the standard ones used for filler/breathers ( DIN 24557/2). In addition the units can be combined with our Fluidcontrolterminal which makes oil care even more technically advanced.
The 63..VA versions are suitable for use with high water based liquids ( HFA).
easy, cost effective installation
continous level / temperature control
4-20 mA analogue outputs
flange standard
one cable for two functions" |
|
Since 1984 B&B Thermo-Technik develop and manufacture successfully industrial temperature probes.
New ideas were always a reason why B&B is one step further than its competitors. Our customers are the focus of our thinking and acting. For them we investigate, analize and realize almost everything in the temperature metering.
Just send us your inquiry and we will supply you with a detailed offer and the solution for your measuring problem.
You will find our range of standard sensors in our Online-Shop:
www.temperature-shop.eu
There you will also get more information about our range of temperature measuring technics:
- Temperature / Humidity sensors
- Thermocouple manufacturers Connectors manufacturers
- Digital Thermomters
- Infrared Thermomters
- Stationary Pyrometers
- Controllers
- Indicators
- Data Loggers
- Hygrometers
- Industrial transmitters
|
|
| Conax Buffalo designs, engineers and manufactures sensors in sizes starting at 0.040"/1mm diameter with probe configurations available in over 30,000 combinations of mounting styles suitable for applications from laboratory to large industrial environments. We offer a complete system approach, from sensor to transmitter, to provide a singular source to satisfy your temperature sensing needs. It's one more way we give you exactly what you want and make it easier than ever. |
|
Sensor (SSA200) with Hermetically Sealed Connector supplier :
The SSA200 series was originally designed for use with portable process plant within the pharmaceutical industry such as fermenter vessels.
It utilises an aerospace/military style of connector in 316L stainless steel with a glass based die-electric industrial seal. This construction allows the whole unit to be left in position on the item of plant during CIP procedures or sterilisation cycles.
The sensing probe itself can be provided with different types of process connection, such as a sliding union, welded on connector with a male thread or a Tri-clover type of hygienic flange. |
|
Watlow can design and manufacture custom industrial temperature sensors and wire and cable to meet specific application demands.
Capabilities include:
* Thermocouple sensors
* RTD and thermistor sensors
* Molding and packaging capabilities
* Agency standards
* ISO 9001 quality auditing procedures
To find out more about custom sensor capabilities, contact your nearest Watlow representative.
|
|
Since 1984 B&B Thermo-Technik develop and manufacture successfully industrial temperature probes.
New ideas were always a reason why B&B is one step further than its competitors. Our customers are the focus of our thinking and acting. For them we investigate, analize and realize almost everything in the temperature measuring.
Just send us your inquiry and we will supply you with a detailed offer and the solution for your measuring problem.
You will find our range of standard sensors in our Online-Shop:
www.temperature-shop.eu
There you will also get more information about our range of temperature measuring technics:
- Temperature / Humidity detectors
- Thermocouple specifications Connectors specifications
- Digital Thermomters
- Infrared Thermomters
- Stationary Pyrometers
- Controllers
- Indicators
- Data Loggers
- Hygrometers
- Industrial transmitters
|
|
Temperature sensors suppliers, humidity sensors, pressure sensors manufacturers, frost protection manufacturer of thermostats, pressostats, explosion proof
Passive, potential free binary and modulating sensors, series ExSens, for temperature, humidity and pressure, with manufacturer certificate, in acc. with ATEX 94/9/EG for use in hazardous areas zone 1, 2, 21 and 22 (in acc. to sensor type), for all kind of gas, mixtures, vapours and dust.
Sensors for room, duct or tube mounting (in acc. to type).
Modulating sensors series ExSens connectable to transducers seriess ExCon-A, RedCon-A or EXL-IMU-1.
odulating sensors series ExPro connectable to transducers seriess ExCon-D and RedCon-D.
Binary sensors series ExSens connectable to switching module series EXL-IRU-1 |
|
| Relative humidity transducers from Sensirion have become the market standard, since they were launched in 2002. Nowadays the company yearly sells millions of humidity sensors all around the world. The sensor solutions are designed for diverse applications such as data logging, climate control, and antifogging. They hence measure relative humidity and temperature in different kind of products. The digital humidity sensors work with a capacitive measuring principle. Thanks to its unique CMOSens® technology, the humidity sensors allow precise humidity and temperature measuring at low cost. |
|
Transducer and switching modules for temperature, humidity and pressure, explosion proof
Elektrical, explosion proof trandsucer, series ExCon-A, Red-Con-A, ExCon-D, RedCon-D and EXL-IMU-1 as well as switching modules series EXL-IRU-1, to connect modulating or binary temperature, humidity and pressure sensors, in acc. with ATEX 94/9/EG for use in hazardous areas zone 1, 2, 21 and 22 (in acc. to sensor type), for all kind of gas, mixtures, vapours and dust. 24 VAC/DC supply, adjustable on site, integral display for programming and for actual value indication.
series ExCon-A for modulating, analogue sensors (type ExSens) and ExCon-D for modulating, digital transducers (type ExPro), for use in hazardous areas zone 1, 2, 21 and 22. series RedCon-A modulating, analogue sensors (type ExSens) and RedCon-D for modulating, digital sensors (type ExPro), for use in hazardous areas zone 2 and 22.
series EXL-IMU-1 for modulating, analogue sensors (type ExSens) for use of sensors in zone 1, 2, 21 and 22, the module must be installed in the safe are and is prepared for DIN rail mounting.
series EXL-IRU-1 for binary, analogue sensors (type ExSens) for use of sensors in zone 1, 2, 21 and 22, the module must be installed in the safe are and is prepared for DIN rail mounting. |
|
- Standard, easy-to-order assemblies fit a variety of applications
- RTDs, thermocouples, and industrial transmitters
- Fittings, connection heads, and thermowells included
- Tip-sensitive, high temperature, explosionproof, and flameproof versions
- FM, CSA, and CENELEC approved models
- Unique spring-loaded holder ensures proper probe contact in thermowells or blocks
- Thermowells & transmitters optional
|
|
The SR Series Ir thermometer is a stand-alone two-color sensor designed to provide a temperature signal directly to process driver or monitoring devices. Ratiometric thermometry provides reliable temperature measurements in difficult applications with changing emissivities or unresolved targets. The SR spot pyrometers Do not require a separate indicator/processor, therefore saving on installation space and costs. These IR industrial thermometers are available in focusing single lens reflex or fiber optic versions.
The 1100 Series is an accurate, reliable and economical high temperature noncontact temperature sensor. It provides a continuous non-linear temperature-dependent output. This electro-optical transducer allows noncontact temperature measurement of higher temperatures. Measure temperatures from 1000°F (550°C) to 6000°F (3400°C).
|
|
These RTDs cover the full temperature scale of the international standard EN60751. Precision sensing elements and nickel alloy sheaths are capable of measurements from -200 to 850°C (-328 to 1562°F) with typical ice point drift less than ±0.05°C.
600°C models have stainless steel sheaths for reduced cost. They use the same element structure as 850°C models for excellent accuracy and stability.
- Platinum elements to EN60751, Class A or B
- English and metric diameters
|
|
Description
The fibre optic temperature probe TP-02 is a high resolution temperature sensor supplier. The sensor makes use of the inherent temperature sensitivity of the Fibre Bragg grating as well as the thermal expansion of its housing. The packaged FBG is positioned inside a stainless steel tube with a diameter of 6 mm and is terminated with an optical connector. Pigtail length and connector specifications can be specified following the needs of every application.
Features
- The temperature probe TP-02 can measure temperatures with a resolution of 0.04 °C and an accuracy of 0,4°C. The sensor can be used in harsh environments and is pressure tight up to 150 bar.
- The sensor can also be connectorised at both ends to make series configurations possible.
- There is also the possibility to foresee an integrated adapter at both sides of the temperature probe.
Applications
Pipeline monitoring, process control, ... |
|
Sensors for applications that require an enlarged operating temperature range
from -40°C ... 100°C. Customized sensors for temperature ranges beyond 100°C as requested.
Inductive sensor
Switching distance 1,5mm to 15mm
Operating voltage 10 - 30V DC
Operating temperature -40°C - +100°C
Switching distance 1,5 - 15mm
Protection class IP67
Max. Switching frequency 300 - 2000Hz
Housing brass, nickel-plated
Output signal:
PNP / NPN N.O.
>>> Different sensor versions/catalogue on request. |
|
| Conax Buffalo Technologies offers thermocouple assemblies specifically designed for durability and reliability in applications to 4200˚ F (2315˚ C). Such applications generally involve oxidizing, reducing or inert gas atmospheres that challenge the life of the thermocouple. Numerous options in thermocouple type, sheath materials and termination styles are available. Assemblies can also include adjustable mounting fittings, thermowells and ceramic tubewells. |
|
In numerous branches of industry heat-treatment and combustion processes play a decisive role during production and in the quality of the final product.
These applications have one thing in common:
Due to the high temperatures thermocouples are almost always used. Besides the non-precious-metalcontaining ones, mainly types E, J or L, K and N, platinum thermocouples types S, R or B are increasingly being used.
These must be protected against contaminating, corrosive and/or abrasive ambient influences.
For various applications we offer different combinations of ceramic and metallic protection resp. mounting tubes. You will find a list of the designs AM and BM, resp. AMK and BMK, resp. AK and BK, resp. AKK and BKK in our product information ''Straight Thermocouples''. |
|
EE32/33 Series
Humidity / Temperature transmitter for High Humidity and Chemical Applications
The highly accurate EE32/33 series are designed for fast and reliable measurement of relative humidity / dew point temperature / absolute humidity / ...under the most demanding conditions.
Neither condensation nor heavy chemical pollutions will affect prompt and reliable measurements. Process pressures as high as 100 bar (1450 psi) and continuous high humidity are also no problem for the EE32/33 series.
EE31 Series
Multifunctional Humidity / Temperature Transmitter for Humidity / Temperature / Dew Point / Absolute Humidity...
The optimal hardware structure of industrial transmitters of the EE31 series for varying applications is achieved by combining various standard mechanical and electronic modules.
Besides relative humidity and temperature following quantities are also measured:
absolute humidity
dewpoint temperature
frostpoint temperature
specific enthalpy
wet industrial bulb | | |
Temperature sensors
