 |
 |
Leakage current tester 1 μA - 60 A | Fluke 360 FLUKE
The Fluke 360 leakage tester is a rugged and accurate solution for leakage current measurement. Ideally designed for non-invasive checks of insulation condition, the Fluke 360 leakage meter allows you to perform tests without powering down the installation or disconnecting equipment - saving you time, without compromising on quality or safety. The unique jaw design of the...
 |
 |
Earth leakage monitor EN 60204 | EMR4-R Eaton Moeller
EMR4-R Earth-Leakage Monitor– For Increased Operating Safety Low costs thanks to reduce downtimes EN 60204 "Safety of Machinery" stipulates that auxiliary circuits must be protected with earth-leakage monitors in order to increase operating...
 |
 |
Grounding Systems / Ground Monitoring Device Series 8146/5075 and 8125/5071 Monitored electrostatic grounding of tank containers...
 |
 |
Earth leakage monitor DH96WG CIRCUTOR
Reference M2041A Type DH96WG Description earth leakage current...
 |
 |
Leakage current tester 50uA to 50mA | ST5540 HIOKI E.E. CORPORATION
Complete Leak current measurement, an essential part of electrical safety (Medical-use Electrical Devices/For Standard- and Regulation-compliant) IEC 60601-1: (2005) 3rd Edition-compliant The ST5540 complies with JIS, IEC, and UL standards...
 |
 |
Leakage current tester AC max 100A | HT77N HT
The innovative model HT77N is a clamp meter for accurate measurements of very low AC current values. It is mainly employed in measuring leakage currents causing typical problem of RCDs accidental tripping on...
 |
 |
Ground fault indicator PGR-3100 series Littelfuse
The PGR-3100 indicates the presence of voltage on each phase of a three-phase system. The LEDs in the panel light up when voltage is present. When a ground-fault...
 |
 |
Partial discharge measuring system MPD 500 OMICRON electronics GmbH
The MPD 500 simplifies measurement of partial discharges in electrical insulation. Building on OMICRON's many years of experience with partial discharge measurement systems, this system has...
 |
 |
Leakage current tester LINECHEK® 620L Associated Research
The LINECHEK® Model 620L is a fully automated Line Leakage tester that can be configured to perform 8 of the most commonly required Line Leakage tests. The 620L has the most common measuring devices (MD's) already incorporated into the instrument and can perform patient lead tests with an optional scanning...
 |
 |
Partial discharge measuring system DDX 91001 Haefely Test AG
[ Partial Discharge Detector ] The DDX 9101 is the effective solution for routine pass/fail partial discharge testing. It has...
 |
 |
Ground tester 0 - 1 000 Ω AEMC Instruments
3-Point Ground Resistance Testers The AEMC® 3-Point Ground Resistance Testers are available...
 |
 |
Leakage current tester max. 0.9 A | TOS3200 Kikusui Electronics
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment. It enables...
 |
 |
Digital ground tester DET 2/2 Megger Limited
The DET2/2 digital ground resistance tester provides a wide resistance range from 0.010 Ω...
 |
 |
Ground fault indicator Fisher Pierce® series Thomas & Betts
Fisher Pierce® Faulted Circuit Indicators (FCIs) for both overhead and underground applications are cost-effective tools to more quickly locate faults thereby reducing...
 |
 |
Ground tester 0.025 - 1500 Ω | 382357 Extech
382357: Clamp-on Ground Resistance Tester Non-contact measurements of ground conductors without need for auxiliary...
 |
 |
Leakage current tester 92-4A ELABO
ELABO leakage current measuring devices - can be configured for a wide range of standards. Thanks to the modular structure of the measuring circuits and the extremely precise...
 |
 |
Partial discharge measuring system max. 34 kV | PD30E PD30E/TD b2 electronic GmbH
PD30E measurement of partial discharges By measurement of partial discharges with the cable diagnostics systems PD30E or PD30E/TD by b2hv, the dielectric condition of a medium voltage cable can be evaluated. As an expanded device PD30E/TD comes with an integrated tan delta diagnostics system! The cable diagnosis system PD30E consists...
 |
  |
Leakage current tester 200 mA - 1000 A | DT-9812 CEM Instruments, Inc
Large tranceformer jaws of 68mm diameter makes it possible to clamp on all three or four wires (3 phases) together for leakage current...
 |
 |
Partial discharge measuring system LDS-6 Doble Lemke
Digital Partial Discharge Measuring and Diagnostics System for industrial and general HV test floor environments. The LDS-6 is a highly sophisticated digital...
 |
 |
Partial discharge measuring system XDP-II ndb Technologies
he XDP II is a portable device for, online, factory and laboratory partial discharge measurement on electrical apparatus, or components. The XDP II can be used in accordance to IEC 60270. It records partial discharge measurements for computer analysis and diagnostic using the optional XDP II software...
 |
 |
Leakage current tester Min. 0.01 mA, Max. 60 A | AC50A Amprobe
Functions Leakage current measurement Voltage and resistance measurement Continuity test with beeper Product information Manual...
 |
 |
Leakage current tester 100 - 240 V AC, 30 A | LT-30HC E D & D
Model LT-30HC Product Details * Features product ground switching (grounding conductor maintained to device under test when not measuring...
 |
 |
Leakage current tester LCM 500 Doble Engineering
The Leakage Current Monitor (LCM) system measures the resistive component of continuous leakage current in gapless metal oxide surge arresters (MOSAs). The LCM is connected...
 |
 |
There are mainly two types of LC measuring methods: Touch Current (TC) and Protective Conductor Current (PCC). Touch Current is...
 |
 |
Short-circuit indicator 400 - 800 A | ELBOW HORSTMANN
ELBOW The ELBOW-mounted short-circuit indicator offers field adjustable discrete trip settings of 400 or 800 amps. This unique patented design offers...
 |
 |
Partial discharge test set PDTS HIPOTRONICS, Inc.
Hipotronics and Robinson Instruments team up once again as your reliable, single source supplier for partial discharge equipment. We offer a full line of AC and DC systems to suit a wide range of...
 |
 |
Ground fault indicator Lind Equipment Ltd.
Static Ground Monitoring Systems In tests, many standard grounding clamps in use today show very high resistance readings when clamped onto conductive objects with insulating surfaces. This may result in the...
 |
 |
Earth leakage monitor KPM105x series Meagacon AS
KPM105x - EARTH CURRENT GUARD FOR SYSTEMS WITH GROUNDED NEUTRAL Grounded neutral earth current Protection Definite Time Trip Delay Two individually setable alarm relays For use with 1A current transformers or CBCT Very...
 |
 |
Partial discharge measuring system HydroTrac™ IRIS POWER
Unlike periodic on-line PD testing, the HydroTrac instrument provides the maintenance professional with an opportunity to: Automate the measurement (on-site or remotely). Integrate...
 |
 |
Partial discharge measuring system DWX-series RM Prüftechnik GmbH
The partial discharge measurement of electric motors and...
 |
 |
Leakage current tester EN60601, EN60990 | GLP2-e Schleich GmbH
GLP2-e/i leakage current Going future. The introdruction of the testing device GLP2 was revolutionary. On the basis of a modular concept, this compact and handy tester offers a great number of testing features...
 |
 |
Leakage current tester 150 - 300 V, 0.3 - 10 mA | 229-2 Simpson
Testing for dangerous small leakage currents is easy with the Simpson Model 229-2 Leakage Current Tester. For use in appliance field service, in the lab, or...
 |
 |
Leakage current tester 60 - 256 V, 16 A | AI 5001A SPS electronic
The safety test of electrical devices must, after having been tested without current and depending on the relevant test standard, be completed by a line leakage measurement with increased...
 |
 |
Leakage current tester 6160 E.D.C. S.r.l.
This is an instrument for the measurement of leakage current on domestic appliances and electromechanical and electro-medical equipment using a single phase supply and following standards CEI 62-5 and EN60335-1. The instrument supplies a voltage (0-260Vac) to the equipment under...
