|
|
* Explosion-proof plugs and socket-outlets PX
* 20 A
* Up to 420 V
* Automatic IP65 watertightness when connected without additional manipulation being necessary
* Silver butt contacts for optimum current transmission
* No access to live parts (IP2X with lid opened)
* Sturdy metal housing
* 6 different keying positions
* ATEX Directives 94/9/EC and 99/92/EC
* EN 50014, EN 50018 (explosion proof safety "d"), EN 50019 (increased safety "e")
* EN 50281-1-1 (flammable dust)
* IEC 60079-0 and IEC 60079-1
* IEC/EN 60309-1
|
|
# Explosion-proof plugs and socket-outlets with an integral switching device
# 20 A - 125 A
# Up to 750 V AC
# Automatic IP65 watertightness when connected without additional manipulation being necessary
# Silver butt contacts for optimum current transmission
# No access to live parts (IP2X with lid opened)
# Sturdy metal housing (mechanical resistance IK10)
# 12 different keying positions
# ATEX Directives 94/9/EC and 99/92/EC
# EN 50014, EN 50018 (explosion proof safety "d"), EN 50019 (increased safety "e")
# EN 50281-1-1 (flammable dust)
# IEC 60079-0 and IEC 60079-1
# IEC/EN 60309-1
|
|
BARTEC’s plug-and-socket devices for areas in which an explosion hazard exists are particularly well-suited for use in raw atmospheres because of their high degree of IP protection and their resistance to chemicals. Their integrated switch function gives them the ability to switch overloads as per IEC/EN 60947-3 Cat. AC 22 or AC 23.Silver-plated butting contacts ensure a constant contact pressure with low transfer resistances.
Plugs/couplers:
The modular design of the plug-and-socket system allows both plugs and couplers to be supplied. They are supplied in unmounted state.
Wall socket:
BARTEC supplies both a fully certified wall socket and a socket with a 30° adapter to flange onto housings.
Plug-and-socket devices from BARTEC are approved in accordance with the European directives not only for Zone 1 and 2, but also for Zone 21 and 22. Likewise for Class I Div. 2 Groups A, B, C, D and Class II Div. 2, Groups E, F, H in accordance with the American standards.
|
|
|
|
|
|
Providing electrical energy there, where it is most needed - even in hazardous areas for the Zones 1, 2, 21 and 22.
Place changeable electrical apparatus have generally high requirements on the energy/power supply. The CEAG wall socket for instance can be mounted on to the pre-installed mounting frame without having to use tools - installation without a hot work permit.
A hight safety standard, a steady hold and faultless contacting even under vibration or the effects of an aggressive atmospheric environment are the basis for a secure and reliable utilization.
CEAG plugs and sockets offer more, apart from the proven technology, this product series is defined by its innovative details. For example, the very efficient cable strain relief or the new coding system of the various versions offers different solutions for a secure and problem free utilization in all areas.
Just to round the product off, the user in the normal industrial sector becomes exactly the same product advantages. Robust industrial versions fulfil all requirements appertaining to mechanical and chemical durability
|
|
|
|
|
|
wired shunts
Are you working in the business of restistance welding? Brouwer Metaal offers wired shunts in a variety of designs and dimensions based on your specifications and applications.
Whether you are specialised in seam welding, projection welding, or butt welding you will need wired shunts that can resist temperature fluctuations. We offer wired shunts made out of a wide array of copper alloys. No matter what the circumstances are, it is essential that you can work with parts that allow high thermal stability. Brouwer Metaal will work with you to produce wired shunts that fit your needs. It is even possible for you to offer us a drawing and we will be able to deliver a product in all possible dimensions.
Brouwer Metaal has been on the forefront of offering innovations and new designs for years, and we can now truly claim to be a major player on the resistance welding market. Our experts are constantly cooperating with our customers to prepare the perfect laminated shunts. Our wide range of products ensures that our customers get the exact products (whether those are laminated shunts, electrode holders, or wire shunts) and materials that they need to ensure the highest quality welding process.
More information can be seen by choosing in the menu on the left. If you would like to receive more specific information regarding our products, please contact us
|
|
We offer you an extensive range of flexible power transmission components. Our diverse manufacturing processes facilitate the production of highly flexible braided cables matched to suit your specific application, ready-assembled connecting components or welded high-current connectors. From the smallest ground or earthing tapes up to high-current cables with 6000 mm² conductor cross-section – almost all conceivable applications are covered. Whether in air-cooled or water-cooled designs, we can offer you the right components and solutions.
Please contact us directly for technical support.
|
|
High quality and competitive price:
KINTO is one of the leading suppliers in China specialized in manufacture of copper parts for electrical applications.
Product range:
- copper flexible connectors made out of copper strips
- copper flexible connectors made out of baided tapes or stranded ropes
- flexible insulated busbars
- primary copper contacts (contact fingers, contact blades, tulip type contacts, bell type contacts, sleeve type contacts,...)
- primary copper connectors
- copper clamps and other customer copper parts
We use technologies such as press-/diffusion welding, braze welding, cold-pressing, stamping, deep-drawing and high precision machining.
The contact areas can be zinned or silver-coated according to customers' requirements.
We are a ISO9001 certificated company with strict quality assurance system, and we have advanced production and testing equipments to assure the quality of each product.
|
|
Brouwer Metaal is specialised in the production of laminated shunts. This product is produced according the drawings or samples of the customer.
We developed a special production method which leads to a considerable extension of the life time.
|
|
We offer you an extensive range of flexible power transmission components. Our diverse manufacturing processes facilitate the production of highly flexible braided cables matched to suit your specific application, ready-assembled connecting components or welded high-current connectors. From the smallest ground or earthing tapes up to high-current cables with 6000 mm² conductor cross-section – almost all conceivable applications are covered. Whether in air-cooled or water-cooled designs, we can offer you the right components and solutions.
Please contact us directly for technical support.
|
|
High quality and competitive price:
KINTO is one of the leading suppliers in China specialized in manufacture of copper parts for electrical applications.
Product range:
- copper flexible connectors made out of copper strips
- copper flexible connectors made out of baided tapes or stranded ropes
- flexible insulated busbars
- primary copper contacts
- primary copper connectors
- copper clamps and other customer copper parts
We use technologies such as press-/diffusion welding, braze welding, cold-pressing, stamping, deep-drawing and high precision machining.
The contact areas can be zinned or silver-coated according to customers' requirements.
We are a ISO9001 certificated company with strict quality assurance system, and we have advanced production and testing equipments to assure the quality of each product.
|
|
FEATURES
* High 300A current rating
* Mates with .125" flat bus bar blade
* Hot pluggable contact
* UL and CUR recognized
BENEFITS
* Small size provides dense power packaging
* Simplifies construction and lowers cost
* Supports hot swapping on 48 volt DC bus
* Product safety and electrical performance has been verified to the highest standards
|
|
The Han® K 3/0, Han® K 3/2 and Han® HC Modular series are designed as connectors for high-voltage and high-current applications.
The connector rating extended from 200 A to 650 A and 2000 V or 4000 V.
|
|
* Up to 400 A
* Up to 1000 V
* No on-load disconnection
* Automatic IP54 watertightness when connected without additional manipulation being necessary
* IP66/67 as option
* 3Ph+E+ 2 auxiliary contacts for electrical interlocking
* Silver butt contacts for optimum current transmission
* Socket-outlet safety shutter, no access to live parts
* Sturdy metal housing, surface-mounted box made of stainless steel
* Standard series draw mechanism made of stainless steel
* In compliance with the European Low-Voltage Directive
|
|
|
|
|
|
HIGH AMPERAGE/ROUGHNECK
Simple to Connect and Disconnect
No tools of any kind are required to connect or disconnect the connector. An external "U" shaped clevis pin locks the halves together eliminating the possibility of accidental disengagement which can cause disruption of service and electrical shock hazards. The clevis pin is designed to permit insertion of a safety wire to provide additional security or the ability to padlock.
Safety
"Roughneck" Plugs and Receptacles feature totally shielded contacts. The synthetic rubber insulator extends past the ends of both male and female contacts for complete safety. Male contacts are equipped with Cooper Interconnect Cam Lok's patented Safe Front Insulated Tip to minimize potential shock hazard. It provides the safest high amperage connector in the industry.
Positive Power Connection
Silver plated high conductivity copper alloy contacts provide minimum resistance, minimum heating.
Colored Insulators for Identification
Eight colors are available to provide easy circuit identification when mating plugs with receptacles. Color coding helps prevent reverse phasing on AC circuits or cross polarization on DC circuits to assure correct rotation of motors while providing for operator safety. The insulators can be fastened to the cable by hose clamp or by field vulcanizing. Inexpensive portable vulcanizers are available. Refer to Bulletin 590.
|
|
|
Fischer high voltage connectors are available in various body styles and sizes. To avoid unintentional disconnection, plugs can be engineered with an integral safety locking ring.
|
|
|
The single-pin High Voltage Connectors of Series-100 enable improved application-flexibility by providing different metric cable-glands. The cylindrical wedging results in a crucial improvement for screen connections. Series-100 is designed for operating voltages up to 100 kV DC and is available in 25 A or 50 A versions.
|
|
|
The single-pin High Voltage Connectors of Series-S are designed for operating voltages up to 40 kV DC / 25 A. Some types contain mounting plates in order to facilitate installation and structuring. Furthermore the connection of a shield is possible.
|
|
|
Series-VarioPro is based on an entirely variable assembly concept of fully compatible elements. All versions of this miniature High Voltage Connector share the same POM or PTFE insulation sleeve-design enabling combinations of up to 3 contacts per connection. Series-VarioPro resists operating voltages up to 11 kV DC / 13 A and provides excellent performance and flexibility at minimal space requirements, easy maintenance and a high safety standard.
|
|
Series-MC represents our latest generation of multi-pin High Voltage Connectors. Substantially reduced in size and weight these HV-Connectors withstand operating voltages up to 10 kV DC / 13 A. They can be equipped with up to 5 contacts. Contacts can be crimped or soldered and are suitable for diverse cable diameters. Both sides of the connection can be configured as plug or socket while cable side is equipped with an EMC-gland bushing for sealing and screen-connection.
Type SB MC 520 has extended and heat resistant PTFE insulation sleeves and is the latest design of this series. The connection can handle an operating voltage of up to 20 kV DC / 13 A and is also suitable for applications with pulsed high voltage.
|
|
|
The multi-pin High Voltage Connectors of Series-M are anchored in a firm screw-housing, designed for operating voltages up to 15 kV DC / 30 A and can be equipped with up to 9 coded contacts. Both sides of the connection can be configured as plug or socket while cable-sockets can be angled and equipped with an EMC-gland bushing. One or more leading contacts can be assigned to execute a starting sequence, an earth connection or confirm a safety loop.
|
|
The Han Hv E® / Han® HvES series is designed for industrial applications up to 830 V.
Terminations offered are either crimp or screw types for Han Hv E® versions, or cage-clamp terminals in the Han® HvES inserts.
All inserts have a PE contact and also 2 additional last mate first break relay contacts.
|
|
New inserts 830V series CME/CMSE/CMCE
Features:
- number of poles: 3, 6, 10
- connection with screw terminals, with crimp terminals series CC (16A) or spring connection terminals
- electric features according to EN 61984 (2001-11)
rated current: 16A max
rating voltage: 830V with pollution degree 3
impulse withstand voltage: 8 kV
- auxiliary contacts: 16Amax 500V/6kV/3 (male contacts with anticipated opening).
- limit current curves and technical characteristics in the catalogue CN04
|
|
revos POWER
The high-voltage connector from Wieland Electric. The contact inserts and multipole adapters are designed for currents exceeding 16 A; they are also available in a contact mix with screw connection. The components are perfectly protected inside the revos BASIC housings. revos POWER is used in mechanical and system engineering for small drives, motors, pumps or frequency converters.
|
|
• Ratings to 16A, 250V ac
• IEC60320 style inlets/outlets
• Fused versions
• Illuminated and non-illuminated switch options
• Flange or snap to panel fixing
• Wide choice of terminals
• RoHS compliant
|
|
With over 26,000 combinations Bulgin’s Polysnap mains power inlet modules offer a very adaptable and flexible solution to panel design.
Polysnap allow combinations of mains inlets and outlets, filtered inlets, switches, fuseholders, voltage selectors, indicators and circuit breakers mounted in either horizontal or vertical format bezels ready for quick snap-fit assembly. The compact design occupies the minimum of panel area and a single rectangular mounting hole, offering easy installation for this mains power entry module.
To complement Polysnap the Polyflange range offers a flange fixing alternative for designers who prefer the security of screw fixing.
All types and variations are available through Bulgin’s extensive distribution network.
|
|
A full range of quality mains rated inlets, outlets and connectors conforming to IEC and EN 60320 specifications carrying UL, CSA, VDE and other approvals. With electrical ratings up to 20A, 250V (UL) these connector ranges offer solutions to most mains powered equipment and cable applications. The combinations of mounting styles and terminations include: flange fixing, snap to panel and PCB mounting versions together with 2.8/solder tabs, 4.8 and 6.3 faston tabs, screw terminal and PC spill versions. Completing the range are insulating boots, retaining clips and safety covers.
In addition to the standard black moulding, most styles are also available in either white or grey and special colours to match OEM equipment can also be supplied.
|
|
_ Connectors IEC EN60320
_ Connectors NEMA
_ Modules thorn-taken
_ Modules thorn-switch
_ Modules portafusibile thorn
_ Modules portafusibile thorn-double quantity
_ Modules thorn-switch-portafusibile
_ Prewired Connectors
|
|
EN60320 inlets range from Bulgin Components is specified for use in all types of electrical equipments, and has an impressive list of international approvals.
The standard range offers one of the most comprehensive range of the market.
Variants offered include: flange and snap-in type, PCB mounting, fused inlets, with or without filters, hot condition types, and inlets with integral suppression and capacitors.
To complement the range, appliance outlets to IEC320.2.2 are available with various mounting options and termination styles.
Mating connectors in rewirable and cordset form complete the range.
|
|
Heycoc IEC 320-C13 Snap-In Power Outlet Connectors
Snap-in IEC power outlet suitable for chassis from .032" (0,8mm) to 125" (3,2mm) thick.
Allows for standardization of equipment for use throughout the world.
Nickel-plated brass ecu lads; horizontal terminals aic two-piece riveted contacts.
All sizes rated al 15 Amps/250 Volts (10 Amps in Europe).
Molded of lypc 66 Nyton". Flammabsty classification 94V-0; temperature index 65°C.
For tab connector data click here
|
|
|
|
Electric power-supply connectors: 
