|
|
The ASX Series is a family of High Performance Switching AC power sources covering the power range from 1.5kVA to 6kVA (12kVA to be released soon). The product line offers both single and three phase models.
Power conversion within the ASX Series is achieved by high frequency pulse width modulation, resulting in cool, quiet and efficient operation.
Key Features Provide Application Versatility
- CE or ETL Listed available on request
-22 Waveform Library - Arbitrary Waveform Industrial generator
-15 to 1,200 Hz Operation - 5,000 Hz Bandwidth
-Precision True-RMS metering of volts, amps, and power for professional displays and reporting
-RS-232 Interface with SCPI compatibility
-1 Phase/3 Phase Switch Selectable Output from front panel or bus command
-99 stored programs for both static and dynamic Transient Testing
-LabVIEW for Windows®/LabWindows® drivers
-Waveform Creation by Harmonic Synthesis
-Harmonic Analysis (Voltage and Current)
-Metering of RMS and Peak Values
-Continuous Self Calibration (CSC)
-Precision Voltage Programming - 0.05% with CSC engaged
-Programmable Output Impedance
-Up to 0-300 VAC Direct Coupled Out
-Power Levels from 1.5 kVA to 12 kVA
|
|
The G-Series are Solid State AC Power converters from 18kVA to 90kVA.
G-Series Systems are readily configurable as manufacturers of frequency converters, line conditioners, programmable industrial test systems, and uninterruptible power systems.
The basic building block of a G-Series AC Power System is the mainframe. The mainframe consists of the professional cabinet and AC to Dc power supply. Up to five mainframes may be paralleled to increase system output power up to 90 kVA.
Each Pacific power source is burned in and meticulously tested before it can leave the Pacific factory. With close attention to detail, handcrafted workmanship comes through with every system delivered.
Due to its modular design, failed device disconnect circuitry, and on-line module replacement, Pacific G-Series Systems are unmatched in reliability and ease of service.
|
|
The AMX Series is a family of High Performance Linear AC power sources covering the power range from 500 VA to 12 kVA (Optional to 30kVA). The product line offers both single and three phase models.
An exceptionally broad bandwidth (50 kHz small signal) combined with peak/RMS current of 4-6:1 give the AMX Series the ability to produce high quality, low distortion output power into the most dynamic loads.
Key Features Provide Application Versatility
-CE and ETL Mark available
-IEEE-488.2 or RS-232C with SCPI compatibility
-LabVIEW for Windows®/LabWindows® drivers
-Waveform Creation by Harmonic Synthesis
-Graphical Analysis (Voltage and Current)
-Harmonic Analysis (Voltage and Current)
-Metering of RMS and Peak Values
-Continuous Self Calibration (CSC)
-Line Sync Option
-6:1 Peak Current Capability
-Low Impedance for IEC555 Testing
-Programmable Output Impedance
-Up to 0-300 VAC Direct Coupled Out, Higher voltage ranges available
-1 Phase / 3 Phase Switch Selectable from front panel or bus command
-20-5000 Hz Full Power Bandwidth
-Power Levels from 500 VA to 30 kVA
-Externally Referenced Meter Calibration
|
|
| Our power supplies suppliers are used in test laboratories, service centres, research and development departments and for production quality testing. They can be supplied with isolation windings, manual or automatic controls, electronic regulators or rectifiers to provide a DC output. |
|
With the combined voltage and current source in a single compact professional chassis, the FX Series is the ideal choice for the simulation of high power professional levels. Either single or multi-phase, this versatile source can simulate power levels from just a few milliwatts
to 54kW single phase or 162 kW three-phase and provides a universal system for both manual and programmable control applications. |
|
Alternative power supply specifications 150 va
The EFS 8171 power supply provides a sinusoidal output, isolated from the line.
The output frequency may be set from 50 to 60 Hz and adjustable from 0 to 700 vrms in 6 ranges. |
|
The RE2 Series has an autotransformer with multiple sockets, each one of which are electrically joined to a solid-state switch. These switches are controlled by a industrial control card with a built-in micro-processor, which controls the output voltage and depending on its level, chooses one or another socket for the purpose of obtaining the most optimum voltage level and with the pre-programmed precision. It has a servo-system which controls the output voltage instead of the input voltage.
Using similar technology, the PLC2 series also incorporates a primary-secondary low capacity, galvanized isolated transformer, and therefore achieving a perfectly stable voltage and the elimination of all kinds of electrical noise.
Both series ensure a perfectly stabilized and "filtered" supply line.
|
|
| Sola/Hevi-Duty's ferroresonant power conditioners protect equipment from all power problems other than a complete loss of power. They excel at tightly regulating voltage within ±1.0% for input variations up to +10%/-20%, provide superior noise attenuation and are designed to withstand the harshest electrical environments. With no moving parts, Sola's ferroresonant power conditioners are virtually maintenance-free. |
|
| LCR offers a broad range of standard off the shelf Power Entry Professional filters and Filtered Power entry modules. In addition, LCR also offers standard off the shelf Power Line Filters (Power Inlet Filters). All of these Emi filters are available in both general purpose and low leakage current medical versions. |
|
| Spectrum Control EMI filtered power products prevent unwanted interference from entering your system, as well as eliminate emissions that can contaminate the AC power grid. Our standard and custom products are available in a wide range of AC/DC current and voltage ratings to address EMI filtering for high current applications. All Spectrum power products are designed to meet global EMC emissions regulations. |
|
| RADIUS POWER offers one of the most extensive range of standard and custom Emi filters and Emc filters. From industrial to medical, RP can provide the right filter solution for all applications requiring EMI professional filters, AC filters, DC filters, single phase filters, three phase filters, IEC inlet filters and PEM or power entry module filters. All standard filters are safety approved to the applicable UL, CSA and CE standards which represent one of the most extensive product crosses to major competitors such as Corcom, Schaffner and Delta. |
|
| The DeviceNet protocol dramatically reduces costs by integrating up to 62 devices on a 4-wire trunk network. Communications data is carried over two wires with a second pair of wires carrying power. Discrete and analog devices may be connected into the DeviceNet protocol. |
|
| AS-Interface networks up to 62 field devices onto a single pair of wires that delivers both signal and power. Actuator specifications Sensor Interface, or AS-Interface, was developed by a group of sensor manufacturers and introduced into the market in 1994. Since that time, it has become the de facto standard for discrete sensors in process industries throughout the world. AS-Interface may be used in hazardous process environments using explosion proof, tray cable, nonincendive and for nonincendive wiring protection concepts. |
|
| Foundation Field network H1 level has been designed as a digital replacement of the 4 to 20mA standard in the process industries. Foundation Fieldbus is also a LAN (Local Area Network) for instruments used in both process and manufacturing automation with built-in capability to distribute the control application across the network. The physical wiring is also fully compatible with intrinsic safety (IS) or nonincendive wiring standards and may be used in hazardous, as well as general purpose areas. In hazardous areas standard explosion-proofing or power limited concepts may be used, as well as IS concepts, offering greater cabling design flexibility. |
|
This technique makes it possible to improve in a considerable way consumption of energy for brazing compared to traditional technologies. (3 to 4 times less power consumption for the same result).
Moreover this technology adapts perfectly to new nanomaterials with difficult coating like sheet metals THLE for example.
The speed of welding is quite higher than traditional technologies what makes it possible to improve rates of welding and thus the productivity. Moreover, the nanomaterials with strong thermal conductivity like aluminum or brass become weldable then without the need for an installation of several hundred kVA (example: With a whole of welding of 65kVA, we can weld triple thickness of aluminum of 2mm).
The energy losses being strongly decreased, the requirements in cooling are reduced what limits pollution generally and that also reduces the expenses of infrastructure related to the installation of such a unit (drivers, less powerful concerned with safety units).
Lastly, the experience gained with several systems already established in the car industry, of the electric household appliances or of the tooling showed us that the volume of consumable strongly decreased thus carrying out advantage of economies. |
|
| The ISA range of Inverter power supply units provides the highest level of control available today in large scale resistance splicer. The ISA-500AR, ISA-1000AR and ISA-2000AR are intelligently packaged in “NEMA” style industrial enclosures and are designed to deliver robust performance in the harshest of production environments. The ISA models can deliver 500, 1000 and 2000 amps of primary welding current, respectively. |
|
Protection Industrial filters are used on distribution networks which have a high THD (Total harmonic distortion), when the final target is to compensate the power factor at the fundamental frequency.
Its purpose is to avoid overloads due to harmonic currents in the capacitor, deflecting them to the network.
Protection filters are made with serial reactors and capacitors supplier. The tuned frequency of each unit is adjusted between the fundamental and the lower harmonic present in the net, which usually is the 5 th order.
In this way, the filters present high inductive impedance for all the harmonic frequencies. |
|
MTE Matrix Industrial filters solve the problem of harmonic distortion on virtually any kind of six pulse rectifier. These power sources are commonly found in three phase electronic equipment such as adjustable speed motor drives, suppliers of welders, battery chargers, servo drives and other equipment.
Harmonics are a problem
Harmonic distortion has become an increasing concern for facility managers, users of automation equipment and specifying engineers alike. Harmonics not only waste energy, but they reduce equipment life, electrical system reliability, system efficiency and equipment productivity.
Guaranteed results
Unlike other harmonic filter technologies, the performance of MTE Matrix Harmonic filters is guaranteed! On AC variable frequency, variable torque drive applications (professional fans & pumps), Matrix filters will meet the guaranteed maximum levels of THID (total harmonic current distortion) all the way from no load to full load. Additionally, Matrix filters will not cause power system resonance nor attract harmonics from other non-linear loads. No system analysis is required to select and apply Matrix Filters.
|
|
| The GEMTRAP® line of fixed, harmonically suppressed condensors permits the installation of power factor correction capacitors on systems with nonlinear load components. The GEMTRAP® system can be tuned to any desired frequency but is normally tuned to the 4.7th harmonic. |
|
Performance:
The CXH series of hybrid, high frequency switched mode power supplies is designed to operate at a fixed frequency over the range of 2 to 40 MHz. The rugged professional amplifier design is well suited to demanding industrial applications where stability and reliability in the presence of erratic loads is required. The solid-state driver section features microprocessor control for precise power control and diagnostic monitoring.
Applications:
The CXH series of high power supplies provides stable, reliable RF power for industrial heating applications including drying, plastic welding, silicon industrial crystal growing and flat panel.
Features:
Standard power ranges: 15kW, 25kW and 50kW
Rugged, reliable design for years of trouble-free operation
Simplified operation through microprocessor- controlled user interface
CX series solid-state driver requires no tuning or adjustments
Water cooling increases tube life by reducing thermal stress in high VSWR mismatched loads
RS-232 package standard
ETL Mark on CXH 25kW |
|
| MTM Power GmbH, the specialist for high-quality smpss, offers in its program DC/DC converters for railway applications of the series HVC with 150 W and 250 W. These devices are available with an input range of 400…975 VDC and the standard output voltages of 24 VDC and 36 VDC. With these high voltage converters it is possible to supply electronical equipment out of 600 V / 750 V contact wire. The DC/DC converters are used for supplying points, signal lamps and electronic monitoring of the rail net. The specific feature of the series HVC is its use as a self starting module for trams or trolley buses with exhaustive discharged batteries so that the towing process can be avoided. The rugged design together with high-quality components guarantee the high reliability in vehicles even under severe shock and vibration conditions. The high efficiency of 83 % allows an operation without forced ventilation. Moreover the converters work with an ambient temperature range from –40…+85 °C acc. to EN 50 155. |
|
Sprecher Automation provides primary technology and secondary systems for high voltage switchgears.
|
|
Performance:
The CLF series professional generators provide stable process power up to 5 kW. The half-rack supplies operate at any fixed frequency from 20 to 50 kHz. The full- rack models can operate at any fixed frequency from 20 to 450 kHz or auto-tuned up to +/- 15% bandwidth. In many applications, the combination of auto-tune and excess power headroom will allow delivery of power to changing reactive loads without the need for mechanically tuned matching networks.
Applications:
The CLF series is designed to meet the performance demand in RF-driven plasma systems for semiconductor processing. Applications include etch, RIE, parallel plate, ICP, RF sputtering, CVD and PVD, as well as induction and dielectric heating processes in industrial systems. |
|
Looking into the future!
Finland, Jyvaskala January 2006 Jean Mueller launched their new IP20 protected L-shaped busbar system for the Scandinavian market. This system was especially designed for the Jean Mueller, vertical SL-fuse switch disconnector cassette system to protect people from touching the live copper bars. Next to their already existing busbar solution with flat copper bars this completes the ranges for the Scandinavian market. The question now rises if there is an enclosure solution which can handle both busbar systems into one solution?
The Eldon answer for the ABB and Jean Muller Vertical cassettes
In close co-operation with both ABB and Jean Mueller, Eldon has developed a ready to use market solution for both types of cassettes. The SL-fuse disconnector of JM and the InLine cassette of ABB. The new enclosure type is called MCBAxxxxV for Vertical mounting of the units. Customers who are buying the Eldon Multi-Flex® solution can decide either to build-in the IP20 protected busbar system or the standards flat copper busbar solution. Both will fit.
Read more in www.eldon.com
|
|
The Entellisys low-voltage switchgear is a breakthrough in power distribution protection, control, monitoring, diagnostics, and ease-of-use. System functionality is based on synchronized, real-time information from every industrial circuit breaker, simultaneously processed in one place.
Entellisys helps to reduce costs, shorten schedules, and increase reliability throughout the process of designing, installing, maintaining, and owning your low-voltage power distribution switchgear. In one real-world example, Entellisys saved its user $50,000 during design and installation of a large system, and will save up to $500,000 each and every year during operation and maintenance |
|
|
|
AC / AC Power supplies, AC Conditioners and Filters
