|
|
| MTM Power GmbH, the specialist for high quality power supplies manufacturer, offers in its program DC/DC converters for automotive applications. The series WRC is available with 30, 60, 100 and 150 W. The converters are designed for mobile use acc. to EN 50 155, LES-DB-BN 411 002 and IEC 571-1 (railway, automotive). The battery voltages 24, 36, 72, 90 and 110 V +40/-45 % are covered with three input voltage ranges. All four power ranges have a high efficiency and are available with single or dual output voltages. The converters have an extreme high reliability (MTBF >1.000.000 h, TA = +40 °C) and an isolation of at least 2,1 kVDC (prim.-sec.). The temperature range is -40...+85 °C acc. to EN 50 155. Other important features are resistance against vibrations and reverse polarity protection at the input. The power supplies can be used in 19" racks or for wall mounting with H15 interconnection. The series WRC needs no ground load, is short circuit protected and has extensive monitoring and protection systems. |
|
- Robust low-power chromated aluminium enclosure
- Wide range PSU for 24, 36, 48, 72 and 110 V
- Processor unit based on PowerPC® MPC5200
- Large selection of I/O modules
- Configuration as control system or distributed I/O
- Simple snap-in to individual I/O function blocks
- Hotplug of the I/O modules
- Own self-diagnosis for each module
- CANopen system bus under VxWorks®
- Full EN 50155 compliance
- Safety requirements according to SIL3 |
|
Absopulse Electronics designs and manufactures rugged, high performance DC-DC converters for almost any input/output and mechanical configuration requirement, with output power ranging from a few watts to over 30kW. These converters are suitable for a wide range of environments, including railway, industrial, military, marine, airborne, utility and telecommunications.
Absopulse's railway suppliers of power supplies are designed to meet rail-specific standards including EN50155 and EN50121-3-2. They are typically encapsulated in a in thermally conductive MIL-spec. silicon rubber compound to ensure immunity to shock, vibration, moisture, salt and airborne contaminants. These encapsulated units operate in ambient temperatures ranging from -40°C to +85°C and humidity up to 95%, and are conduction/convection cooled.
Our rugged, dc-dc converters offer:
- DC inputs: 12Vdc, 24Vdc, 36Vdc, 48Vdc, 72Vdc, 96Vdc, 110Vdc and custom
- High input voltages up to 800Vdc
- DC outputs: 3.3Vdc, 5Vdc, 12Vdc, 15Vdc, 24Vdc, 36Vdc, 48Vdc, 125Vdc 250Vdc and custom
- High output voltages to 800Vdc available
- EMI filtering to meet any standard
- Conformal coating or encapsulation (potting) to ensure immunity to shock, vibration, humidity, moisture, dust and insects available
- Operating temperature ranges including -40°C to +85°C available
- Full electronic protection
- Alarms (form C contacts) option available on most designs |
|
Chassis mount DC/DC converters, cooled by professional fan or air circulation, compact design, high power:
- 25W to 350W
- Input voltages from 9,2V to 144V
- Output voltages 5V, 12V, 24V, 48V |
|
| MTM Power GmbH, the specialist for individual suppliers of power supplies, offers DC/DC converters for worldwide industrial application with an output power from 1,5 to 200 W. They are available with input voltage ranges of 2:1 and 4:1 and output voltages between 1,8 V and 48 V as single, dual and triple output and also as costumized versions. The converters are built in a plastic or metal case. The different cases are DIL 24 or SMD up to 10 W, 2" x 1" cases up to 20 W, 2" x 2" cases up to 30 W, quarter brick with 75 W, half brick with 50, 75, 100 and 150 W and full brick cases with 200 W. Further features are high efficiency of up to 94 %, low ripple&noise, isolation up to 3 kVDC as well as various options like external output voltage trimming and remote control. |
|
Customer specific manufacturer of power supplies and power conversion systems
Our professional development engineers solve even the most difficult problems in accordance with your specifications.
Based on our thorough experience and development process, we have become experts for our customers when it comes to professional packaging power supply solutions. In this way we can relieve our customers of development and application expenses and provide the necessary environment for trouble-free operation of their devices by using our highly reliable power supply units.
Our vast experience provides a great professional platform for us to deliver industry specific power supply solutions.
Whether it involves meeting the demands of the professional rail industry, or under-standing the issues faced by communications engineers, Zentro-Elektrik has the expertise to provide application know how, working with customers from conception through to manufacture of a professional safe and reliable power supply solution. |
|
Compact DC/DC converters for DIN rail and wall mounting
At 100 Watt and 500 Watt the latest DC/DC converters from Zentro Elektrik extend the existing comprehensive range of converters.
The compact DC/DC converters are designed for applications in automation engineering, power supply unit and power station engineering, in traffic systems and railway in particular, and in mechanical engineering. They are air-cooled and have many control, operating and display elements.
Connections are made by means of easy-to-use screw terminals.
The converters are distinguished by a high degree of efficiency of > 80% and comprehensive protective and control facilities such as protection from overload and overvoltage, thermal protection and decoupling professional diodes. Options such as a varistor at the output, to prove additional overvoltage protection or a signal relay, further distinguish the
GWH 100 / 500 series of converters. Up to 3 units with active current sharing can be switched in parallel to extend power. |
|
The environmentally sealed professional converter reduces truck battery volts to a 12 V output to supply power for vehicle lighting and accessories, including head lights, warning lights, industrial blowers, windshield wipers and horns.
- Voltage Input Range : 24 to 48 and 72 to 80 volts
- Voltage Output : 12.5 volts DC
- Current Rating : 16 amps continuous
- Frequency : Constant - 15 kHz
- Ambient Temperature : 0° to 40° C
- Input Professional filter : Included for use with SCR and transistor traction controls
Features and Benefits :
- Terminals and circuitry are isolated from the converter cover - not isolated from battery input
- Thermal protection within the converter will cause the converter to operate at a reduced output in cases where it sees excessive loads, such as a continuous current draw above 16 amps, until the load is reduced
- Converter is normally energized when the key professional switch is closed, and ceases operation when the key switch is open |
|
| MicroPower Direct offers a full line of miniature low cost DC/DC power converters. Including many new models, like our new line of miniature POL regulators. With well over 2,000 standard models, we offer high performance application solutions for designers requiring miniature size, high efficiency, high isolation, reliable field operation and low cost. |
|
MAA02 Series
Features
- Regulated output
- 500 VDC isolation voltage
- 24-pin DIP Package
- Low ripple and noise
Other products available: |
|
| DCDC converters are the power dispensing that output a fixed voltage efficiently, converting the input voltage. There are three types of DCDC converters, step-up DC/DC converters, step-down DC/DC converters, and step-up/down DC/DC converters, Multi channel DC/DC converters. They respond to cus to mer needs lining up four types of control. PWM controlled types are highly efficient and excel in the ripple and the noise of Output voltage . PFM controlled types consume only a little power even if operated all the time, especially when lightly loaded. PWM /PFM switchable types work at PFM control when loaded lightly and switch to PWM control when loaded heavily, au to matically. |
|
| Our Maxi, Mini and Micro models (full, half, quarter-brick) feature a patented low noise design with the highest reliability and power density available. Selecting the right model for the application is streamlined since there are an unlimited number of models that can be configured using our intelligent design tools. |
|
Orion DC / DC Converters : 12 / 24 / 48 / 96 Volt
Possibly the widest range on the market! Both isolated and not isolated models are available.
An ever-increasing amount of electric equipment is being used on vehicles and boats. Because most low-voltage equipment, such as navigation and radio equipment, mobile telephones or car hi-fi systems, is designed for 12 Volts, Victron Energy supplies DC/DC converters which deliver a stable 12 Volt supply from a 24 Volt system.
Next to converters from 24 V to 12 V, a wide range of other models is available.
|
|
| The new primary switched DC/DC converters with 250 W and 400 W output power of MTM Power GmbH are especially designed for automotive applications. They operate according to the push-pull principle, i. e. the input dc-voltage is chopped by two push-pull working transistors with a frequency of approx. 60 kHz. With the help of a transformer and a secondary linear choke, a galvanically isolated output voltage (12 V or 24 V) is produced which is adjusted by pulse-width modulation according to the current mode principle. The series PCMD250W and PCMD400W are available with input voltages of 24 VDC (16,8…36 VDC), 80 VDC (50…150 VDC) or 110 VDC (66…154 VDC) and can be connected via screw suppliers of connectors. The dimensions are 150 x 86 x 55 mm (L x W x H). Due to this compact design, they are also suitable for applications where only little space is available. The converters need no ground load, are maintenance free and short-circuit protected by primary and secondary power limitation. They are vacuum potted and prepared for the use in devices with Protection Class. As an option, they are available for the use in railway applications. Further features are a mechanically and electrically rugged design using SMD-technology and an automatic piece-by-piece test. |
|
| These primary switched DC/DC converters of MTM Power GmbH, the specialist of individual switched mode power supplies, are especially designed for automotive applications and operate according to the push-pull principle, i. e. the input dc-voltage is chopped by two push-pull working transistors with a frequency of approx. 70 - 100 kHz. With the help of a transformer and a secondary linear choke, a galvanically isolated output voltage is produced which is adjusted by pulse-width modulation according to the current mode principle. The converters need no ground load and are short-circuit protected by primary and secondary power limitation. The converters are maintenance free, vacuum potted, prepared for the use in devices with Protection Class II and fulfill the low voltage directive. They show a mechanically and electrically rugged design using SMD-technology and undergo an automatic piece-by-piece test. To ensure a smooth operation, it is necessary to mount the converters on a heat-dissipating surface. The converters are available with 75 W, 120 W, 150 W and 200 W output power and the following connecting types: flying leads or screw supplier of connectors. |
|
| The product family PMG/PCMG with DC input voltage completes the range of primary switched MTM Power Modules. The modules offer an input range of 20...72 VDC and allow - due to the different types available in this series - efficient solutions in numerous application fields. They are available with single, dual or triple outputs. The single and dual (sym.) versions are UL 60 950 and UL 508 approved. Dimensions are 90,5 x 65,5 x 33,5 mm for PCB-mounting (PMG) and 120,0 x 65,5 x 33,0 mm for chassis mounting (PCMG). Thus, they offer the same dimensions and pinning as the standard AC/DC and low voltage modules of the same wattage range which allows the customer to design only one layout for standard AC, low voltage and DC input. The vacuum encapsulated devices offer an isolation of 3,3 kVrms and comply to the up-to-date EN standards as regards CE conformity. Further features are rugged design, SMD-technology, automatic 100 % final test and 100-%-burn-in-test. The series PMG/PCMG offers 15 W or 30 W constant output wattage, is short circuit protected and needs no ground load. |
|
SMD-Package 1 to 15W
Our range of isolated DC/DC converters in SMD package offers products from 1 to 15W with unregulated or regulated output voltages. All models provide high pin accuracy and are qualified for automated ick-and-place machines.
They can withstand the high temperatures in lead-free reflow solder processes and comply with IPC J-STD-020C standard. All products can also be supplied in tape and professional reel package.
High Performance 3 to 60W
Our TEN series is an extensive range of high performance DC/DC converters with output power ranges from 3 to 60W, offering excellent specifications and very high power density in shielded metal packages. Models with wide 2:1 or ultra-wide 4:1 input ranges are available. All TEN series models offer an extended operating temperature range of -40 to 85°C and provide an internal EMI-filter. |
|
Compact DC/DC converters for DIN rail and wall mounting
At 100 Watt and 500 Watt the latest DC/DC converters from Zentro Elektrik extend the existing comprehensive range of converters.
The compact DC/DC converters are designed for applications in automation engineering, power dosing and power station engineering, in traffic systems and railway in particular, and in mechanical engineering. They are air-cooled and have many control, operating and display elements.
Connections are made by means of easy-to-use screw terminals.
The converters are distinguished by a high degree of efficiency of > 80% and comprehensive protective and control facilities such as protection from overload and overvoltage, thermal protection and decoupling professional diodes. Options such as a varistor at the output, to prove additional overvoltage protection or a signal relay, further distinguish the
GWH 100 / 500 series of converters. Up to 3 units with active current sharing can be switched in parallel to extend power. |
|
| XP Power announces its JCA series of miniature, board-mounted low power DC/DC converters. Measuring just 1 x 0.8 x 0.4 inches (25.4 x 20.3 x 10.0 mm), the device's shielded metal package is 0.25 inches (6.4 mm) shorter than the 1.25 inch (31.8 mm) industry norm. Using the customary 24-pin DIP layout, the units occupy 20% less printed circuit board area than traditional products. This allows designers to reduce the size of new developments or add in more features, while maintaining the industry standard pin-out makes the industrial converter an ideal drop-in replacement for existing designs. |
|
| MTM Power GmbH, the specialist for individual professional power supplies, has designed a new generation of DC/DC converters: the series PCMDS60W. They can especially used in automotive applications. These primary switched DC/DC converters are available with an output power of 60 W and operate according to the push-pull principle, i. e. the input dc-voltage is chopped by two push-pull working transistors with a frequency of approx. 70 kHz. With the help of a transformer and a secondary linear choke, a galvanically isolated output voltage (5,2 V, 12 V or 24 V) is produced which is adjusted by pulse-width modulation according to the current mode principle. The converters are available with a wide input range for battery voltages of 24 V, 36 V, 72 V, 96 V and 110 V acc. EN 50 155. The dimensions are 130 x 69 x 30 mm (length x width x height). Because of this flat design, they are also suitable for applications where only little space is available. The maintenance-free converters are connected via spring clamps supplier, which meet the special requirements e. g. in railway applications as regards to vibration resistance and reduced time for wiring. |
|
MTM Power GmbH, the specialist for high quality smpss, offers in its program the new DC/DC industrial converter series URC for automotive applications. Due to the ultra wide input range of 14,4…154,0 VDC, the 50 W or 75 W converters can be operated at all standard battery voltages (24 / 36 / 48 / 60 / 72 / 110 VDC ±40 %) in railway vehicles acc. to EN 50 155 and in stationary applications. There are 8 different versions with single, dual or triple outputs available. The converters can be used for 19" rack or wall mounting with H15 connector manufacturers and can be switched on and off by the enable input. Further features of the URC series are input and output voltage monitoring, high temperature range, high reliability and long life.
|
|
Absopulse Electronics offers a line of plug-in (Eurocard) DC/DC converters designed for railway and other harsh-environments. These units utilize field-proven topology to deliver any DC output up to 130Vdc. They can typically be operated from supply voltages of 24Vdc ((14.4–37V), 36Vdc (22–55V), 48Vdc (28V-74V), 72Vdc (42V-110V), 96Vdc or 110Vdc (57V-168V). Other inputs are available on request.
Absopulse’s line of plug-in (Eurocard) railway converters are designed to meet the requirements of EN 50155 for electronic equipment used on railway rolling stock. They also meet EN 55022 Class B EMI and EN 50121-3-2 (EMI and EMC). The plug-in (Eurocard) series is rated for operation over a -25 to +70oC temperature range without derating, with natural convection cooling. Features typically include full electronic protection on the input and output, optocoupler, optional alarm output and optional control input. An optional built-in redundancy diode to allow for parallel connection to achieve higher output power or N+1 redundancy is available on most designs.
These compact plug-in modules are typically used in 19” rack-mount applications. They are heavily ruggedized and conformal coated and designed to meet IEC 61373 Categories 1 A & B shock and vibration standards.
Absopulse Electronics provides an extensive range of suppliers of power supplies for operation in railway, industrial and other extreme environments in encapsulated or vented, chassis mount packages. If our standard designs do not meet your requirements, our engineering team will provide a cost-effective solution to meet your exact specifications. |
|
| The DC/DC power supply systems of the series MPG from MTM Power, the specialist for high-quality unparallely professional power supplies, are designed among others for different applications in transportation, telecommunications and the charging of lead batteries during stand-by parallel operation. The universally useable, modular and easy-to-scale system is based on the DC/DC converters of the series PCMD200W and PCMD400W which are proved in transportation applications. The series MPG2 is available with 2 plug-in positions and a total output power of 500-800 W and the series MPG3 with 3 plug-in positions and a total output power of 750-1.200 W. With different wide input voltage ranges between 14,4 VDC and 154 VDC, the devices supply an output voltage of 12, 24, 48, 72 and 110 VDC. The output voltage operates with UI characteristic curve. The system can be switched into an energy-saving stand-by operation via a remote control input. Further features are signalling of input and output voltage by an LED as well as a potential-free power good signal. The whole system is passively cooled by convection and is designed for an ambient temperature range of -40...+70 °C. |
|
|
|
DC / DC Power supplies, Converters and Regulators
