|
|
Current Rating: 3 amps max
Dielectric Withstanding Voltage:
600 VAC RMS
Insulation Resistance:
5000 Meg ohms min @ 500 VDC
Contact Resistance:
26 milliohms (65 mv) max @ 2.5 amps
Mating/Unmating Force:
Forces not to exceed 6 oz/contact
Temperature Cycling:
-55 ° C to +125 ° C, 5 cycles
Humidity (Mated):
IAW MIL-STD-1344, Method 1002.2, Type II, Omit Steps 7A & 7B
Vibration:
IAW-MIL-STD-1344, Method 205.1, Test Condition IV, 20 g's
Mechanical Shock:
IAW-MIL-STD-1344, Method 2004.1, Test Condition E, 50 g's
Durability:
500 cycles
Contact Resistance after Durability:
26 milliohms (65 mv) max @ 2.5 amps
Mating/Unmating after Durability:
Forces not to exceed 6 oz/contact
Salt Professional spray:
48 hrs IAW-MIL-STD-1344, Method 1001.1, Test Condition B
Low Professional level Contact Resistance after Salt Spray:
28 milliohms max (2.8 mv) max @ 100 milliamps
Contact Resistance after Salt Spray:
28 milliohms (70 mv) max @ 2.5 amps
Mating/Unmating force after Salt Spray:
Forces not to exceed 6 oz/contact
Contact Retention after Salt Spray:
Minimum of 5 lbs contact retention
Thermal Vacuum Out gassing:
NASA SP-R-0022
Solder Heat & Contact Retention:
360 ° C for 10 sec. & contacts must withstand 5 lbs retention force
Solder ability:
MIL-STD-202, Method 208
|
|
Lapp Canada offers a redesigned line of Nema 4 rated power and signal industrial circular connectors. Lapp's new technology allows the usage of one insulator for all types of connection. The removal and insertion of contacts is now possible without using tools with the capability to retrofit current applications.
These copper alloy/ nickel plated connectors manufacturers are ideal where mating orientation is require, space is limited and connecting and disconnecting is desired. The new design of the coupling allows for use of both screw and push pull connections while still maintaining compatibility. The R2.5 signal series, which is available with 8+1, 9, 12, 16, or 17 contacts, has a patented insulation body which fits all housing designs, and can take both pin and socket contacts in all terminations variants: solder, solder cup, and crimping. The R3.0 series is the substitute for the R2.5 series allowing for more contacts including 21 or 26 contacts. Applications include servo drives, center tools, measuring equipment, industrial encoders, CNC machines, medical electronics, portable or mobile equipment, instrumentation, plus other applications. |
|
Lapp USA offers a redesigned line of Nema 4 rated power and signal circular connectors suppliers. Lapp's new technology allows the usage of one insulator for all types of connection. The removal and insertion of contacts is now possible without using tools with the capability to retrofit current applications.
These copper alloy/ nickel plated manufacturers of connectors are ideal where mating orientation is require, space is limited and connecting and disconnecting is desired. The new design of the coupling allows for use of both screw and push pull connections while still maintaining compatibility. The R2.5 signal series, which is available with 8+1, 9, 12, 16, or 17 contacts, has a patented insulation body which fits all housing designs, and can take both pin and socket contacts in all terminations variants: solder, solder cup, and crimping. The R3.0 series is the substitute for the R2.5 series allowing for more contacts including 21 or 26 contacts. Applications include servo drives, equipment tools, measuring equipment, professional encoders, CNC machines, medical electronics, portable or mobile equipment, instrumentation, plus other applications. |
|
- Push-Pull Manufacturers of connectors made you of plastic
- 7 Colour-Codings
- Solder- and PCB termination
- 1-14 postions, Special Professional inserts e.g. Professional fiber optic, Fluid
- sterilizeable / autoclaveable
- Easy mounting of the connector
- Housing 100 % Touch proof
- Low weight
- Low mating and demating forces
- High chemical resistance
- Special solution like “Disposable”
- Modification of the catalogue version possible
|
|
Complete product range for electrical drive components
ConPower is a complete connector family. It comprises power connectors and feedback connectors specification and is therefore the perfect combination for the time-saving connection of electrical drive components with transmission power up to 630 V and 150 A. |
|
Areas of use
Moulded connections and inter-connections for all types of automated industrial devices
The Senstronic range consists of:
- Lead M8 with 3 contacts
- Lead M12 with 3, 4 or 5 contacts
- Lead M23 s with 9 or 19 contacts
- Lead for 24 V solenoid valves |
|
Signal manufacturer of connectors - longtime proven, matured, good value
The signal connectors are all-purpose connectors, usable for transmitting signal voltages in a frequency range from DC up to 100 MHz with electric currents up to 20 A. The very large range of design types for cable connectors, receptacles and wall bushings enables solutions for almost every application case in the field of mechanical and system engineering. In particular, the wide variety of device flanges in combination with dip solder contacts is unique in the industry. |
|
Rosenberger offers a wide range of high-frequency coaxial connectors.
If you are interested please get in contact. |
|
Fundamental research in particle physics as practised within CERN and other nuclear research establishments requires
more and more complex equipment of high performance in order to achieve the objectives. The needs of such research
contribute to the development of leading products for the whole of industry. For many years LEMO has participated in
this evolution. This has resulted in a range of miniature in line connectors (50 Ohm) with a push-pull self-latching system,
the LEMO 00.250 series. These connectors suppliers now form the basis of the NIM-CAMAC CD/N 549 standard. |
|
Micro-Coax designs and produces a wide range of connectors. We specialize in optimizing the cable to connector junction and most of our connectors form integral parts of our high performance cable asemblies. Our expertise in both cable and connector technology enablesVSWR and insertion loss to be minimized while maximizing the integrity of the joint.
Micro-Coax can provide quick turn-arounds on make-to-order connectors that meet your unique and demanding requirements. Contact us directly for additional information to discuss your connection specifications with our experienced engineering staff. |
|
| The co-axial coupling consists of three parts. The outer hub consists of a series of rare earth magnets that are ground, potted and attached to the inside diameter of a steel hub. The inner hub consists of a series of rare earth magnets that are ground, potted and attached to the outside diameter of a steel rotor. The inner hub is then completely sealed in stainless steel to protect the magnets and rotor from damage or corrosive substances. Typically there is a radial air gap of up to .275" (7mm) between the inner and outer hubs. Conventional bores and keyways are used to drive the inner and outer hubs. |
|
| Pasternack's Adapter Wizard is designed to help you identify the right RF coax adapter to meet your specific requirement. With over 750 different adapter configurations in-stock, both in-series or between-series, there is no need to search different companies for RF coaxial adapters. Pasternack has more RF coaxial adapters in stock than any other company, will ship your order the same day you place it, to wherever you need. |
|
Bus Manufacturers of connector for PROFIBUS 90°
The compact design of the bus connections from the Systeme Helmholz GmbH makes them suitable for use in all Siemens CPU types.
A slide switch sets whether the connector will be used as a node or end of segment. The switch can also be operated when the connector is plugged. The switch setting is clearly visible.
The connector must be used as a node („OFF“) when the incoming bus (A1, B1) and the outgoing bus (A2, B2) are to be interconnected. This deactivates the terminating resistors.
The connector must be set as a segment end (“ON”), on the first and last (extreme) stations of the segment. In that case the terminating resistors are connected on the incoming bus, the outgoing bus is disconnected.
|
|
Air Precision has also developped a range of standard electrical slip rings : EEG, T13 and T20.
They use the same "gold" technology as custom-built slip rings and therefore have excellent electrical qualities and are easily adaptable thanks to interchangeable mechanical interfaces.
Derivates of those standard slip rings are also available.
CONTACT US :
by email : sales@airprecision.com
by phone: +33 1 46 01 21 16
DO NOT HESITATE TO VISIT OUR WEBSITE IN ENGLISH :
www.airprecision-slipring.com
YOU CAN ALSO VISIT OUR FRENCH WEBSITE :
www.airprecision.com/collecteur-electrique/collecteur.asp
|
|
| The LT Series rotating joints from DSTI feature all-aluminum construction for light weight & excellent durability. These units are available with up to (12) independent passages, with optional electrical slip rings with up to (56) circuits. The LT Series products are a readily available solution for todays complex automation requirements. |
|
Rotary Systems' three passage rotary union with integrated 6 circuit slip ring. The union is constructed from plated carbon steel. The union utilizes a hardened and ground shaft, Teflon professional seals and radial ball bearings.
The slip ring is a 6 circuit compact commercial capsule rated at 2 amps/210VDC or 240VAC. Gold on Gold contacts with speeds up to 250 RPM. Several circuit configurations for the slip ring and number of passages on the rotary union are available upon request.
Please contact our Technical Sales department at 1-800-959-0146 with your operating parameters if you need a rotary union with an integrated slip ring. Slip rings are available in various configurations and can be modified to meet your specifications.
|
|
Industrial carts sensors equipped with professional brushes carbon-bronzes, high quality, quasi non-existent wear (not of junction copper to the professional seals fish-plates). Body, platinum and connection box polyamide charged glass fiber. Screw with eyelet and passivated galvanized steel chain. Possibility of twinning the sensors.
Continuity: bandage copper uninterrupted, conducting uninterrupted copper, not of junction = not of wear. Perfect dilation. Always possible extension, one puts a box of connection and one extends with a new section. |
|
For safe, reliable transmission of energy and data, designed of loads of 10 A to 2000 A, variable number of poles and dedicated solutions for specific applications.
- Enclosed conductor rails -
With 5 or 7 poles, individual configuration, various connection systems available as a function of assembly and operating conditions, for indoor and outdoor operation, for straight or curved travel, for loads between 35 A and 140 A
- Multipole conductor rails -
Standard models with 3, 4 or 5 poles, compact hanger manufacturer of clamps (with a single screw) permit configuration of systems with 6, 7 or 8 poles, for loads between 10 A and 125 A
- Single-pole insulated conductor rails -
Number of poles according to specifications, universal installation brackets, for indoor and outdoor operation, heatable, for straight or curved travel, for loads between 10 A and 2000 A |
|
With operations in 30 countries and sales of 1.3 billion euros in 2006, FCI is a leading manufacturer of connections. Our 13,500 employees are committed to providing customers with high-quality, innovative products for a wide range of consumer and industrial applications.FCI designs and manufactures connectors solutions targeting the following market applications:
> AUTOMOTIVE
FCI provides connectors systems for engine, cockpit, safety, multimedia and other electronic applications. Through outstanding quality, cost competitiveness and delivery performance, FCI is recognized by its customers as their strategic partner.
> ELECTRONICS
FCI is a leading supplier of interconnect solutions for networks
and telecommunication infrastructures, consumer electronics, data storage,
medical and instrumentation applications.
> ELECTRICAL
FCI provides a complete range of electrical products that cater to the
vast power utility sector, including construction, maintenance and repair,
public services and central office. We are constantly adding to our range
of products and services by producing targeted solutions for the most demanding tasks.
> MICROCONNECTIONS
FCI is the world’s leading supplier of micro circuitry on flexible professional films
for smart card applications. FCI has solid expertise in consumer peripherals, professional antennas for RFID applications and flexible circuits for customized applications. |
|
| To have more information about Fischer Coax / Triax | | |
Electric connectors, Electronic connectors
