|
|
ERNI has developed a solution to the dilemma posed by high pin-count hard metric (HM) connectors specifications and the need for precision connector mating combined with sufficient play between subtraack guide rails and printed-circuit board (PCB) cards. The answer is ERNI's pre-alignment module.
According to IEC 61076-4-101 standard, 2 mm HM connectors may have hundreds of contacts. At the same time, the plug-in board connectors and backplane connections must mate precisely in order to avoid damage. On the other hand, there must be play between the cards and rails to avoid compression stress on the PCB.
A further reasonable additional option is the electrical contact model. Shielding is low resistant because of gold plating, and therefore allows electric current to flow with 40A at 20°C through a large diameter. A corresponding derating chart is available.
|
|
FCI offers a complete range of reliable, cost effective and innovative solutions for automotive applications. FCI provides connectors specification systems for engine, cockpit, safety, multimedia and other electronic applications. Through outstanding quality, cost competitiveness and delivery performance, FCI is recognized by its customers as their strategic partner.
Applications, products and services :
> Passenger cars & light vehicles
> Motorized vehicles
|
|
| Rosenberger FAKRA*-RF connectors supplier have been especially designed to fulfill the tough requirements of the automotive industry. A comprehensive coding system offers 11 mechanically keyed and colored coded housings for modern automotive applications, e. g. GPS, keyless entry or GSM mobile radio. |
|
IDC Female Connectors specifications For Cables
Type C
Right Angle Female Connectors
Type Q
Type Q/2
Type Q/3
Type R
Type R/2
Type R/3
Type RD
Type TE
Right Angle Male Connectors
Type B
Type B/2
Type B/3
Type C
Type C/2
Type C/3
Type CD
Type D
Type E
Type E160
Type E80
Type F
Type H-F
Type H11
Type H15
Type M
Eurocard Center Connector
Vertical Female Connectors
Type B
Type B/2
Type B/3
Type C
Type C/2
Type C/3
Type CD
Type D
Type E
Type E160
Type E80
Type F
Type H-F
Type H11
Type H15
Type M
Eurocard Center Connector
Vertical Male Connectors
Type Q
Type Q/2
Type Q/3
Type R
Type R/2
Type R/3
Type RD
Type TE
|
|
Advanced designs and manufactures hundreds of RoHS Compliant screw-machined terminals for our high quality sockets, adapters, and connectors suppliers. Advanced also offers a complete line of EMC® insulated and non-insulated terminals and test jacks for RoHS Exempt applications.
RoHS Compliant terminals are compatible with lead-free processing - select either Matte Tin(M) or Gold(G) plating
|
|
The AVX offers a broad range Battery connectors which are suitable for handheld and portable applications such as: industrial scanners, PDAs, cellphones, industrial modules and medical electronics
If you have any specific requirements, please contact your local AVX sales office for details on how AVX Battery Connectors specifications can assist you in addressing your future requirements, or visit http://www.avx.com/prodinfo_catlist.asp?ParentID=188 for catalog pdfs
|
|
Laird Technologies’ standard precision electronic contacts ground, carry current and signals, and interconnect boards and devices. We offer a wide choice of plating options to allow for the maximum electrical current carrying performance. We have a wide array of designs in standard formats that are ready for production. Installed costs are lower with our tape and reel packaging format.
From concept to placement, Laird Technologies has the expertise to deliver custom precision surface mount contacts. Using the latest computer simulation techniques, we provide properly designed contacts that ground, carry current and signals, and interconnect boards and devices. We do this by using basic geometric parameters (length, width, uncompressed height, compressed height, contact force) to conduct Finite Element Analysis (FEA) on your prospective design. With the FEA results, we can then identify the best design to optimize your product’s operational performance. We also incorporate features to provide for placement and soldering of the contact onto the circuit board. |
|
Manufactured from quality moulding and metal components to ensure a secure and reliable connection, Bulgin’s battery holder range caters for battery sizes 1/2AA, AAA(R03), AA(R6), C(R14), D(R20) and PP3(6R61), accommodating 1, 2, 3 or 4 cells.
There’s a choice of fixing styles including screw and flange panel fixing, PCB and base mounting versions.
The panel mounting versions are now available in two styles; standard fixing and front panel sealed to IP67, extending the applications into harsher external environments where dust or water would inhibit equipment operation.
The open frame styles are designed to be either PCB or base mounted and most have an interlocking facility to join adjacent holders together.
Principle applications include portable equipment and memory back-up.
|
|
BASICS+
Basics+ brings together our proven, standard industrial connectors for board-to-board and wire/cable-to-board applications. Our goal is to save you time by providing “Easy To Use” services. All services are accessible via the dedicated Basics+ web site : www.fciconnect.com/basics
EASY TO SELECT A PRODUCT
This catalogue provides an easy overview of the most standard Basics+ products. For even more choice, our web catalogue provides the step search possibility that guides you step-by-step to your part number
EASY TO GET DOCUMENTATION
Data sheets, product drawings, specifications, application notes, packaging drawings and more are available on the web site for download.
EASY TO GET TECHNICAL SUPPORT
Get your technical questions answered within 24 hours on our e-mail hotline basics.help@fciconnect.com
EASY TO GET SAMPLES
Order a sample today, and you can start to work with your Basics+ product right away! Sample orders can be placed via the web site.
EASY TO GET COMMERCIAL INFORMATION
As a customer, you can have registered online access to prices, packaging quantities, minimum order quantities, and lead times. All the commercial information you need is at your fingertips. |
|
When space is at a premium, our board-to-board connectors suppliers are the perfect solutions. Proven reliability combined with design flexibility provide effective results for even the most demanding SMT and thru-hole applications.
Featured with :
- available in .050" (1.27mm), .079" (2mm), and .100"(2.54mm) pitch
- high density, low-profile interconnects
- high quality screw-machined terminals offer reliable electrical/mechanical interconnects
- wide variety of terminals and plating options
- mezzanine board applications
- unique solder preforms allow multi-tier Z-axis expansion
- RoHS Compliant insulators with either Gold/Gold or Matte Tin/Gold terminal plating are compatible with lead-free processing
|
|
Tyco Electronics' HXC125 Board-to-Board Connectors manufacturer offer a high performance, high density interconnect for today's design challenges.
Connectors are available in 1mm to 4mm heights, with centerline spacing as low as 1mm. This solderless, compression system allows for ease of assembly while offering excellent power management capability. Standard 1.0 mm contacts are rated to 4 Amps each.
|
|
2.54mm Board to Cable Connectors supplier (Latch Headers) Series LPV acc. to IEC 60603-13
Female connectors
IDC
Interlocking latches
Male connectors, with interlocking
Solder
Pressfit
THR (black)
Male connectors, without interlocking (low profile)
Solder
Pressfit
Strain relief clamp manufacturers |
|
Mencom Corporation cable connectors manufacturers, often referred to as circular connections, are produced in a variety of configurations. They are available in molded cable, receptacle, or field wireable with several wire color code choices as well as multi pole choices. Mencom is the only manufacturer to number both the face and the wires on their circular connectors.
Products:
INDUSTRIAL CABLE GLANDS
CAPS
JUNCTION BLOCKS
TERMINATING PLUGS
T's
|
|
The EasyConn PB of Vipa is offering an accessory for practical use with well thought-out performance characteristics. For the first time a micro-controller has been integrated into a Profibus connector manufacturers which can provide information on power supply unit, bus function, termination and possible bus failures via four LEDs. With the integrated PG/diagnosis jack the plug is especially suitable for application in extensive plants.
The bus cables can be easily connected with the insulation piercing technique: open the cover, insert the unisolated cable, close and fix it with the captive screw. Additional security for the connection of incoming and continuative bus lines is given by the transparent cover and its possibility of visual inspection.
Connection with a highly-flexible bus cable from Lapp according to Type A (EN 50 170) will also be possible with immediate effect.
The termination can be activated and deactivated with a comfortable slide switch which also enables the disconnection of the continuative bus line. Thereby tests can be conducted without having to remove or connect cable and plug. The EasyConn PB offers cable outlets in 90°, 45° or 0°. The 90° variant is also available without diagnostic function.
|
|
Profibus connector manufacturers - EasyConn PB
The bus connector EasyConn provides all test functions that speed up implementation and trouble shooting. Four LEDs, visible from two sides, indicate bus and device status.
The integrated EasyConn Controller works with a baudrate of up to 12Mbaud.
Features
• Cable slots with transparent covers
• Metal case ensures high interference immunity
• Cable connection via cutting-clamps
• Captive single-screw installation system
• Integrated switchable terminating resistor
• Integrated PU/diagnostic socket*
• 90°, 45° and 0° cable exit
• Status monitoring via integrated LEDs
Standard bus cable for fixed wiring Features
• Bus cable according to DIN 19245 and EN 50170
• Single core bare Cu wire
• 2 core stranded (red/green)
• Outer sheath PVC mixture (violet, RAL 4001)
• Flame-retardant acc. VDE 0472, Part 804, Proofing type B (IEC 332.1)
* only EasyConn PB 90°, 45°
|
|
Woodhead Introduces the most significant innovation in industrial connectors specification in 30 years!
NEW! Ultra-Lock Connector System
Next Generation M12 Connector Technology
Fast - Simple - Secure |
|
FAST AND CENTRALISED ON-SITE CONNECTION OF YOUR ENERGY CIRCUITS FOR PROCESS AND MAINTENANCE EQUIPMENT.
- compressed air
- cooling fluids
- industrial vacuum
- electricity
To satisfy your requirements in terms of simultaneous connection of air, cooling fluids and electricity, Stäubli has developed the Combitac programme.
CENTRALISED CONNECTIONS FOR MORE PRODUCTIVITY AND BETTER SAFETY.
With the Stäubli CombiTac system, you connect and disconnect your air, cooling and electrical circuits in a single motion with no crossed connection: you save time and improve safety.
COMPLETE AND TAILORED SOLUTION TO FULFIL YOUR NEED
The CombiTac programme, offers you:
- on one hand, complete pneumatic system designed by our R&D department.
- on the other, a wide choice of module units to enable you to configurate the CombiTac solution the best suited to your application.
|
|
Tyco Electronics offers a broad portfolio of connectors specifications for main Memory modules, removable Memory cards and microprocessors made to the many industry standard specifications.
The Tyco Electronics main Memory connectors are made to JEDEC industry standards for SIMM (Single In-line Memory Modules) and DIMM (Dual In-line Memory Modules) for computer and communication applications. Each product family consists of vertical, right-angle and various angled configurations in solder tail, press fit and SMT mounting options. |
|
SAL Connectors specification
The dimensions and construction of the CONEC SAL connector series comply with IEC 61076-2-101.
They are used in many applications in the field of automation technology for signal transmission, power transmission or for data communication in field bus technology.
...with overmoulded cables
reduce installation costs and save time drastically, through the use of connectors with integral wires.
The choice of material and the construction of the connector enable it to be used in a dirty and damp industrial environment.
...for special requirements
are often made of special materials concerning their chemical resistance and temperature stability. CONEC has developed special products for these areas. Special materials are available for a temperature range of 125°C for 6000 h.
Field attachable connectors ...
can be assembled freely and are often required for individual cable lengths, e.g. for the construction of special purpose machines.CONEC offers 4 and 5-pin models here in an axial and angled construction for connectors and adapters. In the angled construction the cable outlet is adjustable in a 90° pitch to the pin layout.
Chassis connectors
Installation flanges are used to produce an M12x1 connection on the device. A newly developed modular system makes it possible to produce a wide variety of combinations among one another.
Field network technology ...
has increased dramatically in the industrial sector over the last few years. CONEC offers connectors for Profibus DP and Industrial Ethernet. Integral M12x1 connectors with corresponding pin layout coding (in acc. to IEC 61076-2-101 standards) are available for both bus systems. |
|
|
Electric connectors, Electronic connectors
