|
|
TL5 Intelligent TEST LOAD for fuel accumulators and professional batteries is a passive electronic load with microprocessor intelligence. Two models, the TL5-20 and TL5-40 are available working in the 0-20.00A and 0-40.00A ranges respectively. Both models have the ability to briefly interrupt current and measure resistance free cell potential following a selectable delay. There are additional inputs for reference electrode and temperature sensor manufacturers. Further expansion via the I/O connector suppliers provides an additional eight digital inputs, eight digital outputs and two analog inputs. The onboard microprocessor controls time keeping, data acquisition suppliers functions, and readings are displayed on a multifunction 80-character LCD display. Two operator selectable current ranges of 0 - 2.000 A and 0 - 20.00 A (or 0 - 4.000 A and 0 - 40.000 A), depending on the model.
The voltage up to 20.00 V is auto ranging. |
|
Emission Reference Sources are small, self contained emitters which generates a known, measured field strength at a standard measurement distance. ERS and EMC10.3G ensures measurement integrity and reduces measurement uncertainty.
ERS and EMC10.3G obtains true end-to-end calibration - including site conditions, professional antenna and receiver.
ERS and EMC10.3G cover frequency ranges from 30MHz to 3 GHz, and have ultra-stable emission levels with traceable calibration.
|
|
| Since its introduction, the PrecisionPoint™ VX platform has been the industry standard for dependable test, analysis and rework of your probe cards. The PrecisionPoint VX3 carries on this tradition for today's fine-pitch, small array probe cards. From logic to LCD drivers, the PRVX3 provides the necessary tool set to meet your testing needs for planarity, alignment, Cres, leakage, probe force and more. |
|
| Professional circuit breakers are one of the critical "safety-valves" of electrical systems and basic maintenance procedures are essential to maintain maximum reliability. As the leading producer of circuit breaker industrial test sets, Mega ohm meter sets the standards of quality and reliability. New technology is incorporated in the circuit breaker industrial test equipment with the launch the DDA (Digital Industrial data acquisition) series of circuit breaker test sets. The DDA controller utilizes digital signal processing (INDUSTRIAL DSP) technology along with variable firing angle and pulse duration control to bring improved accuracy and flexibility to the curcuit breaker testing arena. Megger test sets are available for every budget and test application. |
|
Breakers are situated at the key points of electrical energy transmission and distribution systems. Their reliability has a decisive influence on the availability, safety and economic efficiency of electrical supply networks.
Initially, the reliability of newly installed breakers depends on their construction, the manufacturing quality and the type and scope of final factory inspections and tests. However, once installed on site, only regular tests can guarantee perfect functioning throughout the operational life of a breaker.
Automatic industrial test systems provide precise information as to the state of the switching chamber and drive unit throughout the entire operational life of a breaker without requiring these to be opened. The sheer number of parameters to be calculated, the wide variety of different breakers in use and the harsh environmental conditions encountered during on-site tests make extremely high demands on the test technology involved. |
|
Full Compliance CE Mark test equipment and ANSI transient test solutions. Choice of 4kV or 6kV SURGE professional generators with Combination, 100 kHz Ring, and 10/700 waves plus your choice of ESD, EFT, and voltage DIPS and Interrupts as needed. Integrated, automated, single phase CDN.
|
|
OMICRON's CT Professional analyzer is a unique lightweight electronic multifunctional instrument designed to meet the highest standards for performing excitation, ratio, polarity and winding resistance tests on current transformers (CTs) as well as burden-impedance measurement.
Benefits
* Extremly small and lightweight (< 8kg/17 lb), beneficial for on-site testing
* Reduced commissioning time due to fully automatic testing
* Allows testing and result assessment according to IEC 60044-1, IEC 60044-6 or IEEE C57.13 (ANSI standard)
* Accuracy level (0.02 %/1 min.) enables field calibration and verification of class 0.1 CTs for metering
* Testing of specialized CTs such as TPS, TPX, TPY and TPZ
* Automatic analysis of CTs with unknown data ("name plate guesser" function)
* Recalculation of test results after tests with different burden and different primary current (no further on-site measurements)
* High level of safety - all tests utilize low voltages (120V)
European Patent EP 1 398 644 A1
* Almost unlimited in: Ratio (50 000 : 1), Primary current (999 000A max.),
Knee point voltage (15kV max.)
* Automatic demagnetization of the CT after the test
* Data storage on a removable Compact Flash (CF) card, which can be read by any standard memory professional card reader
* Remote interface to integrate CT-Analyzer into an automatic production process
* Easy importing and editing into MS OfficeTM standard software |
|
Damped oscillatory waves are phenomena associated with the opening and closing of High Voltage (HV) busbars in power transmission stations. The physical environment influences the fundamental oscillation frequency and repetition of the impulses. Repetition frequencies are dependant on the power frequency and distance between contacts. For gas insulated stations this could be up to 5kHz.
The new IEC61000-4-18 standard introduces additional fast damped oscillatory waves at frequencies of 3MHz, 10MHz and 30MHz. These are for testing of signalling and control equipment installed in Gas Insulated Substations (GIS) where the transients occur in metallic enclosures containing SF6 gas.
MIG-OS-OM-EXT has been designed to add fast oscillatory wave capability to existing EMC Partner professional generators.
MIG-OS-OS1 and MIG0603OSI generators deliver 100kHz and 1MHz slow damped oscillatory waves that were previously included in the IEC61000-4-12 standard.
As the application is for power distribution stations, the equipment to be tested is generally connected to 3-Phase power lines. CDN3000-06-25 (manual) and CDN3000A-06-25 (automatic) enable coupling of both fast and slow oscillatory waves. |
|
The ELT-400 is an innovative professional tester for evaluating magnetic radiation exposure in the workplace and in public spaces. The device was developed for use by health and safety officials in industry, by insurance companies and by service-industry users.
The ELT-400 handles almost all of the required measurements in the low to medium frequency range with accuracy and ease. The device is comparable to professional sound level meters, which are commonly used in the workplace to protect against excessive noise exposure.
Options
Use as an active probe with a three-channel analog output for analysis applications involving an oscilloscope specifications or spectrum analyzer specifications.
|
|
Simply the best HARMONIC and FLICKER professional test system available today. HAR1000 does not require expensive and bulky AC sources, it uses a novel technique to provide active compensation of distortion on the national power mains.
Featuring dual analysers, the input and output signal are constantly monitored to ensure compliance. HAR1000 conforms to the latest IEC61000-3-2 Edition 2 but also allows testing to previous standard editions.
HAR1000 can be enhanced with the following accessories.
HAR-EXT1000, three phase system
Adds two further phases to the HAR1000. Simple connection without any hardware modifications mean this powerful extension can be added at any time to an existing single phase system.
HARCS Immunity software
This package can be added to both the single and three phase systems. It extends the system’s emission capability to include power line immunity tests such as harmonic immunity according to IEC61000-4-13, voltage fluctuations according to IEC61000-4-14 and ripple on DC according to IEC61000-4-17.
Adding the EMC Partner PS3, allows testing to IEC61000-4-28 for frequency fluctuations.
|
|
SYS61K
Compliance Professional test system for Harmonics IEC 61000-3-2 and Flicker IEC 61000-3-3
Application:
Evaluation system for testing devices generating harmonics and flicker
according to IEC 61000-3-2 and IEC 61000-3-3 (CE-Conformity)
- Modular structure, 1 to 3 phases realisable with the LMG95 or LMG500
- Power sources up to 5kVA per phase
- Existing customer owned power sources may be implemented, even for systems wich are discontinued in availability and support by their manufacturer e.g. HP/Agilent and others
- Inputs to register additional process values
- Improved analysis by means of integrated statistical and regression algorithms
- Auxiliary measuring signals to find the reason for harmonics and flicker
- EN61000-3-2/A14
- Consulting partnership in standardization commitees assures precocious support of newest professional standards, to be upgraded via internet
- Easy to control with powerful evaluation professional software |
|
| California Instruments professional cabinet systems are carefully designed and manufactured to provide maximum system performance and reduce installation cost. The various elements that make up an integrated high power AC professional test system are carefully assembled in a high quality 19 inch cabinet. All input and output wiring is properly sized and routed for optimal performance and safety. Configuration problems or wiring mistakes are eliminated when ordering a cabinet based multi-box power system like the 15003iX or a three phase compliance test system like the 30003iX-CTS. This translates into faster setup time and reduced installation hassles upon receipt of your power system. |
|
The 1650 Series professional testers verify the safety of electrical installations in domestic, commercial and industrial applications. They can ensure that fixed wiring is safe and correctly installed to meet the requirements of IEC 60364, HD 384 and all relevant local standards.
The unique ergonomic design, low weight, and padded neck-strap to free your hands, make operating a Fluke 1650 multifunction tester a pleasure. With easy-to-operate controls and a large display with exceptionally wide viewing angle, it's also comfortable and safe to use. Select from three models:
- Fluke 1651: Performs all basic installation tests including continuity/insulation/loop impedance and RCD tripping time
- Fluke 1652: Also provides RCD tripping current level and RCD auto-testing
- Fluke 1653: As Fluke 1652 but with earth resistance and phase sequence measurement. Has internal memory and a PC interface for documentation and reporting
|
|
The Electric Field Meter EM03 is a small, compact unit for measuring static electrical charges with digital display in Volts. The mode of function of the instrument is based on the influence principle.
When measuring static charges, the distance between the instrument and the object is selectable between 1 and 20 cm.
The integrated micro-computer automatically converts the measured field strength over the preselected measuring distance (distance between test object and measurement electrode) into Volt, allowing charges up to 200 kV to be measured. |
|
With the Motor Performance Monitor, Baker Instrument Company continues to pioneer new breakthroughs that demonstrate an ongoing commitment to quality, reliability, and competitive advantage. This on-line motor professional analyzer takes the next step in providing complete P/PM programs. It provides root-cause analysis through the separation of mechanical and electrical issues.
The Explorer Series II was superiorly designed to pinpoint challenges (voltage source, VFD, motor, load) your rotating machinery face. This self-contained portable instrument is computer driven with proven engineering, allowing all testing to be accomplished directly from the MCC or from Baker EP connection. |
|
As a response to the measurement requirements for any distribution and control board, CIRCUTOR has developed a new electrical power analyser for three-phase systems: CVM-MINI.
Of course any equipment can measure the main parameters in electrical systems, but the smaller size of the three module, DIN analyser, combined with a large number of advantages, make the CVM-MINI the best option for measurement and energy control solutions:
-Capacity to process more than 213 electrical parameters.
-Din track mounting or panel mounting (72X72) using an adapter.
-RS485 communications with Modbus/RTU protocol.
-Easy to build into existing control systems.
-Programming, measurement, recording and professional control software.
-Universal power dispenser
CIRCUTOR has built into one single small piece of equipment, the performance of any instrument found on any distribution and control board (protection boards, motor and pump control, overload and earth leakage distribution cabinets, etc.), in a size and price which will make any board, no matter how small, be incomplete without the presence of the CVM-MINI.
|
|
| COMBI420 is an innovative meter designed to perform all safety test verifies on electrical installations in compliance to recently standards (VDE0100, BS7671 and so on, measure and save results of environmental parameters (illuminanance, temperature), leakage currents and active power, harmonics, power factor measurements on single phase systems. The meter it's very easy to use and have a wide number of internal features which are selectable by using the multilanguage menu. The instrument permits, moreover, to start principal measures by using a special remote prove (PR400 optional accessory) particular useful to perform tests in very quickly mode and the AUTO internal function to perform sequential measurements of Global Earth Resistance, test on RCDs' and Insulation directly on sockets of civil installations. A contextual help menu selectable by user it's available for each measurement function and permits a valid information during connection of meter to the installation. The newest electronic function selector give to the meter a extreme rugged structure for perfect using "on field". A wide internal memory permits the saving of any measurements and the transfer to PC by serial port with dedicated professional software it's possible. Each measure it's saved with all the sub-results and test parameters with up to two ID locators (selectable by user on meter) in order to reach the exact point where the measure was performed. |
|
Three power quality analysers CA 8332 / CA 8334
Designed for verification and maintenance departments in industrial or administrative professional buildings, the Qualistar CA 8334 enables the user to obtain an instant picture of the main characteristics of electrical network quality. Handy and very compact, this instrument also gives numerous calculated values and several processing functions in line with current standards: EN 50160, IEC 61000-4-15, IEC 61000-4-30, IEC 61000-4-7.
Characteristics:
* Colour Professional lcd screen for graphic indicator
* 3 structured display modes: observation, diagnostic, monitoring
* Complete triple-phase analysis: - voltage, current, - power / energy, - harmonics (up to 50th rank), flicker, - measurement of transients, - alarm trigger...
* Processing of data via PC professional software QualistarView or DataViewer Pro.
* Working memory: 4Mb
* 12-screen record
* Compliant with IEC 61010-1, 600V Cat.III |
|
MCA Plus professional network analyzer is an electronic instrument which allows the measurement of 48 main parameters in the input network in real value and RMS value.
It is specially designed for easy installation and programming. It needs three voltage signals (RST) and current (I1, I2, I3).
MCA Plus is supplied with Industrial lcd screens backlighted for an easy reading at any lighting level. It offers optional communication module and has internal memory. |
|
The UPM315 is a multifunction metering DIN96x96 device with advanced functionality features, suitable for electrical parameters measurement and power quality analysis.
Main features:
- DIN 96 & ANSI 4” Cutout for New or Retrofit Professional panels
- Highly Sofisticated Power measuring device Providing Advanced Functionality Features
- Large Graphic Professional lcd display with Excellent Visibility
- Up to Two Plug-In Options
- THD Even, Odd and Individual FFT Harmonic Analysis up to 50th Order
- Power and Current Demand Calculation
- On-Board Professional memory up to 2MB
- Programmable Min/Max & Energy Data Logging
- Event and Alarm Recording, Waveform Capture, Waveform Display, Phasor Diagrams, Historical Trending, Time-of-Use and more....
The UPM3080 is a multifunction metering DIN144x144 device with advanced functionality features, suitable for electrical parameters measurement and power quality analysis.
Main features:
- Fully Bi-Directional Four Quadrant Readings
- Neutral Current Measurement
- Large Graphic LCD Display with Excellent Visibility
- Up to Two Plug-In Options
- Infrared Communication Port
- THD Even, Odd and Individual FFT Harmonic Analysis up to 50th Order
- Power and Current Demand Calculation
- On-Board Memory up to 2MB
- Programmable Min/Avg/Max and Energy Data Logging
- Event and Alarm Recording, Waveform Capture, Waveform Display, Phasor Diagrams, Historical Trending, Time-of-Use and more.... |
|
- Very high performances, with a remarkable cost efficiency relation
- Convenient application also as simple multimeter
- Accurate measures in true rms (cl.l energy measuring devices IEC 1036)
- Measures and management of the average, maximum and minimum values of the electrical parameters (related to one period and absolutes) for an accurate and complete analysis of the energy distribution lines
- Bi-directional active and reactive energy meters for the energy balance between delivered energy and/or absorbed (Co-generation)
- Energy meters divided up to 8 time bands in 10 periods, for a full management of the energy costs
- Analysis of the Voltage and Current harmonic components, up to 31 order with fundamental at 50/60 Hz
- Possibility of conducting measure campaigns with memory of the electrical parameters, average values, maximum and minimum, and the harmonic components
- Internal clock and calendar (REALTIME CLOCK) Management of optional parameters (non electric even) from additional inputs, performing a complete measure acquisition machine
- Very simple and intuitive to use and to program with a simple menu and flowing visual pages
- Full programming possibilities of the working parameters(set-up, CT and VT ratios, average times, alarms, connections, peripherals, printings, etc.).
- Programmable alarm outputs with parameter's selection for, time delay, maximum and/or minimum hystheresis, etc.
- Input and output contacts situation for operations verification
... |
|
Professional circuit breakers that trip, transformers that overheat, motors that burn out, machines that don't function properly; whatever the problem, you can quickly and easily identify the cause with the Fluke 43B Power Quality Professional analyzer.
As a Power Quality Analyzer it is optimized for industrial measurements on the 50 Hz fundamental frequency. Because its frequency range extends from 10 to 400 Hz, it's also ideal for aviation, marine and railway applications.
Besides the unique extended frequency range, the Fluke 43B is the only instrument that combines the capabilities of a Power Quality Analyzer, a 20 MHz oscilloscope manufacturers, a professional multimeter and data professional recorder in a single tool.
|
|
Features:
- Three phase voltage
- Three phase current and neutral
- Active and Reactive power
- Cos ø
- Active and Reactive energy
- Harmonics software incorporated (up to 51th)
- Flicker
- Disturbances and quality of the distribution system
- Real-time clock
- Average, max. and min. values of all parameters |
|
The MAVOWATT 50 energy and power disturbance professional analyzer is the professional tool for optimized mains quality. It records all relevant measured quantities for supply power, and allows for a detailed analysis of
disturbances. Its versatile concept makes it a true multi-talent.
The MAVOWATT 50 is capable of executing all measuring functions simultaneously, can be used in all types of electrical systems and is equipped with measuring and data interfaces for all practical applications, a
great variety of display modes and various memory functions. |
|
The testing device 92-7G/-7M is concieved for the control via an external PC/PLC. Therefore display and operating devices were renounced. The modular design of the testing instrument permits an optimal adaptation to the individual requirements of the user. Uneeded functions or equipment are omitted. Together with the device ELABO offers an efficient professional software package.
HV
The high-voltage is produced primarily over an internal electronic HV-source with a high clock frequency and regulated within less 10 ms. Because of the internal source a low residual ripple < 3% (accordingto VDE 0432-1) can be realised, also for DC tests with high currents. The synchronisation can be carried out on an external signal, on the mains frequency or internal (free-running). An electronic voltage ramp mode (voltage ramp up and ramp down) allows for tests of electronic equipment, at which a non-destructive test can only be carried out if the test voltage is increased slowly or for test items with high self-capacitances. The integrated residual voltage measurement assures a safe discharge of thecapacitances of the test items.
Insulation resistance
Insulation resistance measurement with voltages from 500 V up to 8000 V DC at full HV-current are possible. The resistance measurement is carried out together with the high voltage test at the sametime.
PE resistance
Measuring of the PE resistance or the voltage drop at the protective earth conductor through fully electronicregulated programmable test current 10 ... 32 A at an AC voltage of 6 or 12 V. |
|
EurotestXA is the top of the range installation safety professional tester with automated testing based on patent pending AUTO SEQUENCE®.
Because of the need to be efficient, fast and competitive but still reliable and concentrated on safety, all the technical content and innovations under AUTO SEQUENCE®, focus on taking care of the testing procedure itself. If you are after a high speed, safety, and reliable least-fuss testing instrument, look no further. |
|
Hipot test to 6kVDC 10mA
Hipot test to 5kVAC 40mA
Ground Bond test to 42 Amps RMS
Insulation Resistance 50 to 1000V
Automated Remote Interface
|
|
UE RAS: REMOTE ACCESS SENSOR - When remote sensing or access is an issue. Easy to install & simple to use.
RAS-MT REMOTE ACCESS SENSOR - Magnetically mounted contact probe with cable and remote access module (RAM) for testing consistency and for hard to reach test points. RAS-MT is included with the Ultraprobe 10,000 Inspection system specifications and is an optional accessory for the Ultraprobe 9000.
UE MMP-7, UE MMP-8 & UE MMP-2U: MAGNETIC MOUNT PROBES - Magnetic Mount Probe | | |
Other electrical measuring instruments
