|
|
|
NETGEAR offers a complete line of reliable, affordable networking switches from high-performing wire-speed Layer 3 managed switches to entry-level managed Smart Switches to plug-and-play unmanaged switches for SMB and the Home. All NETGEAR switches are standards based, fully-compatible with existing 10/100/1000 network infrastructure and easy to use and install.
|
|
|
Offering a combination of mux ratios and wide buses with 5V/3V or 3V/2.5V translation, hot-docking/hot-plugging, bus and load isolation and other features ideal for a variety of applications.
|
|
Moschip family of co-processors provides a companion chip to Moschip Network Appliance Processors. This will allow scalability by adding USB, Serial, Parallel and Display functionality all in a combined solution. The PCI-e bus can be used as a high speed communication link between a processor and co-processor for example.
Not only do Moschip Co-processors integrate with Moschip processors, but they can also be used with other 3rd party processors to gain these added feature sets to their existing devices with a minimal design-in cost
|
|
|
The ZL50117 CESoP processor is a highly functional TDM to Packet bridging device providing both structured and unstructured circuit emulation services (CES) for T1 and E1 streams across a packet network based on MPLS, IP or Ethernet. The ZL50117 also supports unstructured J2, T3, E3 and STS-1. The device incorporates a range of powerful clock recovery mechanisms for each TDM stream and an Ethernet interface for data traffic uplink.
|
|
General overview
Zarlink's Timing-over-Packet (ToP) technology enables accurate timing and synchronization to be distributed across asynchronous packet infrastructures, allowing carriers to con#dently support time-critical services over packet networks.
The patent-pending ZL30301/2 ToP family is built on a processing engine and software solution that encodes and transmits a master clock over existing Ethernet, IP and MPLS networks, and recovers the clock at client nodes.
With Zarlink's ToP devices, Carriers can lower operating costs by migrating to a truly converged network supporting time-critical services, including voice, video and data services. In some applications, ToP technology replaces GPS receivers and T1/E1 connections that are traditionally required to ensure accurate synchronization.
|
|
The Serial RapidIO PCI Bridge provides the capability to bridge between Serial RapidIO and PCI. It is part of a family of bridge devices aimed at applications wishing to take advantage of the Serial RapidIO interconnect.
Serial RapidIO is a switched data communication standard developed for the interconnection of devices on the same circuit board or between circuit boards across a backplane at rates in excess of 10Gbps. It has been developed as a more cost-effective, standards based replacement for expensive proprietary busses in high-performance embedded systems, such as networking and communications equipment and enterprise storage.
|
|
|
Pericom has designed these high-performance devices for next generation markets that include Switches and Routers, Servers, HBAs, Data Storage Systems, PCs, Notebooks, Telecom Equipment, Multi-Function Printers, Test Equipment, Embedded Systems, and Data Acquisition Systems.
|
|
|
|
|
|
PCI & PCI Express Connectivity
Peripheral Component Interconnect (PCI) is an interconnection system between a microprocessor and attached devices. PCI devices are found in two forms. One, in which the PCI IC is incorporated directly onto a motherboard. This is also known as a planar device. Second, is when the IC is integrated onto an PCI device card that will attach to a PCI slot connected to a motherboard.
MosChip's PCI bridge chips provide OEMs low cost solutions for developing products that bring single and multi-channel Parallel, UART and Serial devices to the market place.
PCI Express (PCI-e) is an interconnection system, based on the PCI standard, between a microprocessor and attached devices for high-speed operation. The electrical and mechanical interfaces of PCI-e are not compatible with the PCI bus interface. This bus also provides a high speed 2.5GBs data rate.
Our family of PCI-e bridge chips will integrate Parallel, Serial and USB 2.0 /3.0 interfaces into scalable devices that OEM designers can bring to market in record times with low overall costs to market
|
|
|
TI's PCI bridges provide a high performance connection path between two PCI buses or between a PCI bus and DSP host port. The PCI bridge functions as the traffic coordinator allowing bridge transactions to occur concurrently on both.
|
|
Cypress has the broadest and most flexible portfolio of backplane physical layer (PHY) devices in the industry.
This portfolio includes : HOTLink(R) ; HOTLinkDX(TM) and HOTLinkII(TM).
These transceiver families cover data transmission rates of 50 Mbps up to 1.5 Gbps. These flexible devices are ideal for proprietary serial backplane applications. They also comply with many industry standards such as : Gigabit Ethernet ; Fibre Channel ; Enterprise System Connection (ESCON) ; Digital Video Broadcast - Asynchronous Serial Interface (DVB - ASI) ; Society of Motion Picture & Television Engineers (SMPTE), SMPTE 292M, SMPTE 259M, SMPTE 344.
|
|
Silicon Labs offers a complete family of transceiver and clock and data recovery (CDR) ICs targeted at OC-192/STM-64, 10GbE, OC-48/STM-16, OC-12/STM-4 and OC-3/STM-1 physical layer applications. These highly-integrated devices lead the industry in jitter performance, small package size and low power.
Features
Loss-of-signal alarm
Diagnostic and line loopbacks
SONET-compliant loop timed operation
No external loop filter components
Programmable slicing level and sample phase adjustment
LVDS Low Speed Interface
Single Supply 1.8 V Operation
Multi-rate operation
Low jitter generation
Small footprint
Low power
Applications
Optical transceiver modules
Optical transponder modules
SONET/SDH transmission systems
Add/Drop multiplexers
Digital cross connects
Gigabit Ethernet (GbE)
SONET/SDH/ATM routers
|
|
Since the introduction of the first SONET SerDes ICs over 15 years ago, Vitesse has been a leading supplier of optoelectronics and Physical Layer (PHY) devices for OEMs around the globe.
Vitesse offers a comprehensive family of transport products ideally suited to a wide range of communications applications. Vitesse delivers high-integration and low-power solutions for protocols including Fibre Channel (FC), Gigabit Ethernet (GbE), and SONET/SDH at data rates up to 40 Gbps, with an emphasis on the development of products to lower the cost of bandwidth for applications from 1 Gbps to 12.5 Gbps.
|
|
|
The Fujitsu WiMAX SoC, MB87M3550, fully complies with the IEEE 802.16-2004 standard using an OFDM PHY. The SoC can operate in TDD or FDD modes and supports all the available channel bandwidths from 1.75MHz up to 20MHz bandwidths.
|
|
PROFIBUS :
Link devices
Siemens offers PROFIBUS link devices for different tasks:
Communication between two PROFIBUS DP masters
Connecting RS232C devices to PROFIBUS DP
Connecting PROFIBUS devices through a wireless network
|
|
|
Interface IC solutions ranging from CAN, LVDS, RS-485, RS-232 industry standards to 1394 (Firewire), USB, PCI Cardbus and more.
|
|
|
Interface IC solutions ranging from CAN, LVDS, RS-485, RS-232 industry standards to 1394 (Firewire), USB, PCI Cardbus and more.
|
|
|
Equipment manufacturers will achieve significant power and space savings when using Broadcom's advanced SONET OC-48 and OC-192 chips. Broadcom offers a complete family of SONET transceivers that enable the development of low-cost, high-density optical transport equipment. These high-density solutions handle more bandwidth in a smaller space, enabling telecommunications and service providers to better accommodate data and voice traffic over existing fiber networks.
|
|
General description
The ZL50016 is an enhanced non-blocking TDM switch with 1024 x 1024 channel switching capacity. The device offers per-stream rate selection and conversion, embedded G.711 (A-Law/u-Law) code conversion and simultaneous all-stream Bit Error Rate (BER) testing. It is designed to deliver performance advantages and cost benefits for low-density applications.
|
|
The FX/MX102 is a single-chip device to extract single periodic signals from very high random-noise environments.
Using patented autocorrelation techniques the MX102 will enhance the input signals signal-to-noise ratio by as much as 8.5dB and provide a digital output signal centered at four times (x4) the input frequency.
The amplitude of non-periodic components of the signal is substantially reduced. The patented autocorrelator compares the incoming signal to itself; the more elements of the waveform that are seen as periodic, the higher the energy at the microcircuit output.
The FX/MX102 cascades two autocorrelators, each one improving the signal-to-noise ratio.
|
|
The TH8080 is a physical layer device for a single wire data link capable of operating in applications where high data rate is not required and a lower data rate can achieve cost reductions in both the physical media components and in the microprocessor which use the network. The TH8080 is designed in accordance to the physical layer definition of the LIN Protocol Specification, Rev. 1.3 and 2.0 and SAE J2602.The IC furthermore can be used in ISO9141 systems.
Because of the very low current consumption of the TH8080 in recessive state it's suitable for ECU applications with hard standby current requirements, whereby no sleep/wake up control from the microprocessor is necessary.
|
|
|
|
|
|
General Description
The LVT16245 and LVTH16245 contain sixteen non-inverting bidirectional buffers with 3-STATE outputs and is intended for bus oriented applications. The device is byte controlled. Each byte has separate control inputs which can be shorted together for full 16-bit operation. The T/R# inputs determine the direction of data flow through the device. The OE# inputs disable both the A and B ports by placing them in a high impedance state.
The LVTH16245 data inputs include bushold, eliminating the need for external pull-up resistors to hold unused inputs.
These non-inverting transceivers are designed for low-voltage (3.3V) VCC applications, but with the capability to provide a TTL interface to a 5V environment. The LVT16245 and LVTH16245 are fabricated with an advanced BiCMOS technology to achieve high speed operation similar to 5V ABT while maintaining low power dissipation.
Features
- Input and output interface capability to systems at 5V VCC
- Bushold data inputs eliminate the need for external pull-up resistors to hold unused inputs (74LVTH16245), also available without bushold feature (74LVT16245).
- Live insertion/extraction permitted
- Power Up/Down high impedance provides glitch-free bus loading
- Outputs source/sink -32 mA/+64 mA
- Functionally compatible with the 74 series 16245
-Latch-up performance exceeds 500 mA
- ESD performance:
*Human-body model >2000V
*Machine model >200V
*Charged-device >1000V
- Also packaged in plastic Fine-Pitch Ball Grid Array (FBGA)
|
|
|
|
|
|
General description :
The Intersil ISL324xE devices are 2.7V to 3.6V powered RS-232 transmitters/receivers which meet ElA/TIA-232 and V.28/V.24 specifications, even at VCC = 3.0V. Additionally, they provide ±15kV ESD protection (IEC61000-4-2 Air Gap and Human Body Model) on transmitter outputs and receiver inputs (RS-232 pins). Targeted applications are POS systems, and notebook and laptop computers where the low operational, and even lower standby, power consumption is critical. Efficient on-chip charge pumps, coupled with manual and automatic power-down functions, reduce the standby supply current to a 0.5µA trickle. Tiny 5mmx5mm Quad Flat No-Lead (QFN) packaging and the use of small, low value capacitors ensure board space savings as well. Data rates greater than 250kbps are guaranteed at worst case load conditions.
ISL324xE are 3 driver, 5 receiver devices that, coupled with the 5x5 QFN package, provide the industry's smallest, lowest power complete serial port. The 5x5 QFN requires 60% less board area than a 28 Ld TSSOP, and is nearly 20% thinner. These devices also include a noninverting always-active receiver for "wake-up" capability.
The ISL3243E features an automatic powerdown function that powers down the on-chip power supply and driver circuits. This occurs when an attached peripheral device is shut off or the RS-232 cable is removed, conserving system power automatically without changes to the hardware or operating system. It powers up again when a valid RS-232 voltage is applied to any receiver input.
|
|
|
We invented the charge-pumped RS-232 transceiver. Today, we are the leader in copper-wire data transfer, at speeds up to 800Mbps. Our product line includes USB, RS-232, RS-485, LVDS, and IrDA transceivers as well as Logic Level Translators, UARTs, and SCSI termination products.
|
|
|
LVDS & CML (Buffers and SerDes) Nationals leading edge LVDS and CML multi-megabit & -gigabit products include signal conditioners, serializers/deserializers (SerDes), drivers/receivers/transceivers, crosspoint switches, muxes, 1:n repeaters, buffers, and much more that drive LVDS, M-LVDS, PCI Express, SATA, SAS, XAUI, 4G FC, DVI/HDMI, and CPRI signals over low-cost cables and long FR4 traces. Serial Digital Interface and Data Transmission.
|
|
|
|
|
|
AMIS-30600: LIN Transceiver
The single-wire transceiver AMIS-30600 is a monolithic IC that works as an interface between the protocol controller and the physical bus.
AMIS-30660: CAN High-Speed Transceiver
This transceiver is the interface between a controller area network (CAN) protocol controller and the physical bus and may be used in both 12V and 24V systems.
AMIS-30663: CAN High-Speed Transceiver with true 3.3V and 5.0V logic level interface
This transceiver is the interface between a controller area network (CAN) protocol controller and the physical bus and may be used in both 12V and 24V systems.
AMIS-40615: LIN Transceiver
The AMIS-40615 is a full-featured local interconnect network (LIN) transceiver designed to interface between a LIN protocol controller and the physical bus.
AMIS-40616: LIN Transceiver
The AMIS-40616 is a full-featured local interconnect network (LIN) transceiver designed to interface between a LIN protocol controller and the physical bus.
AMIS-4168x: Fault Tolerant CAN Transceiver
The AMIS-41682 and AMIS-41683 work as the interface between the CAN protocol controller and the physical wires of the CAN bus.
AMIS-42665: High-Speed Low Power CAN Transceiver
The AMIS-42665 CAN transceiver is the interface between a controller area network (CAN) protocol controller and the physical bus and may be used in both 12V and 24V systems.
AMIS-42700: Dual High-Speed CAN Transceiver
Controller area network (CAN) is a serial communication protocol, which supports distributed real-time control and multiplexing with a high safety level.
|
|
|
The CS8406 is a digital audio transmitter that supports 192 kHz needed for next-generation audio formats such as DVD-Audio. It enables consumer and professional audio products to exchange 192 kHz S/PDIF and AES/EBU audio data. The CS8406 accepts and encodes audio and digital data, which is then multiplexed, encoded and driven onto a cable/optical transmission interface. Its flexible 3-wire serial digital audio input port, on-chip channel status and user bit buffer memories allow block-sized updates without the need for external memory. The CS8406 also includes an on-chip, low-skew, low-impedance differential-line driver that permits transmission over longer cable lengths.
|
|
|
Industry standard single and dual drivers and receivers for RS232 and RS562 are available for power supplies from 1.8V to 5.5V with high ESD protection. DTE or DCE configurations are available in 3.3V or 5V versions.
|
|
|
Texas Instruments (TI) provides complete digital interface solutions. High-performance solutions that empower you to differentiate your products and accelerate their time-to-market. TI has experience in highspeed, mixed-signal circuits, system-on-a-chip integration and advanced product development processes. Our solutions ensure you receive the silicon, support tools, software and technical documents to create and deliver the best products on-time and at competitive prices.
|
|
VMB5000A
high speed 3G bridge chip
PC Card to USB + UART Function Versatile Mobile Bridge Chip
Dual port high speed ideal for 3G applications
* Ultra-thin 64 terminal QFN package
* RoHS compliant & Lead-free
* 20MBits/s host interface
VPU16551
vpu16551 PC Card UART
PC Card to UART Bridge Chip
Well proven PC card UART for PCMCIA and CF designs
* Integrated EEPROM for CIS data
* RoHS Compliant & Lead free
|
|
|
|
Peripheral line-drivers, Bus controllers, Network controllers
