|
|
The Vehicle Bus Professional analyzer Speaks Your Language
The Vehicle Bus Analyzer is the first conventional oscilloscope manufacturers to decode CAN serial data into Symbolic (application layer) text. Now, for the first time, an engineer has both the full range of CAN protocol stack information-symbolic, hex, and electrical signal-and the ability to view additional in-circuit electrical signals (detection and suppliers of actuators, voltage levels, transients, etc.) that influence the CAN bus. In addition, up to four different CAN buses can be decoded at one time. Standard and specialized oscilloscope tools can be used to validate and debug designs.
Eliminate the Barriers to Fast Debug
Direct symbolic decoding and triggering allows fast and intuitive understanding of events. Simply load your existing DBC database file into the oscilloscope (no re-entry of data is required); capture CAN message traffic; and all electrical (signal), protocol (hex), and symbolic (application) layer information is quickly displayed on the oscilloscope screen. Use standard oscilloscope and specializedVehicle Bus Analyzer tools to find rare events, automatically measure and statistically analyze event timing, and graph/plot information, including extracted CAN message data.
Unique Measurement Tools
The VBA can make many measurements not possible with other instruments. Aside from timing measurements, the VBA can also extract CAN data from a CAN message stream, graphically plot that data on the oscilloscope display, and compare it to other electrical signals. Here, information on the steering angle and steering angle rate of change is extracted from the CAN message acquisition, rescaled to decimal values, and plotted as a time-correlated "Track" on the VBA display.
|
|
The CAN-Bus Professional tester 2 constitutes a universal measuring instrument for the commissioning, analysis, monitoring, troubleshooting and service/maintenance of CAN-Bus plants.
Typical problems which occur during the operation of CAN-Bus plants, such as node failures, faults in the communication or complete standstill of the plant, often have their origins in the physical bus characteristics. The CAN-Bus Tester 2 provides an overview of the signal conditions on the bus, which helps you locate and rectify frequently occurring error causes without unnecessary delay.
You can already ensure a correct bus cabling and verify its transmission properties when setting up the plant. You can also perform comparing measurements directly on the running plant over its lifetime and thus prevent downtimes. |
|
| Aeroflex is able to offer a wide selection of cellular industrial test sets addressing both mobile and base station test applications. |
|
| Agilent network analyzers accurately characterize components by measuring their effect on the amplitude and phase of swept-frequency and swept-power test signals. |
|
| Snapshot IS provides intrinsically safe data collection / analysis in a convenient, palm-sized package weighing just 1.5 lbs. (680 grams). With both a phase input and a dynamic signal input, it is the industry's only data collector in this size/weight range that boasts both intrinsically safe operation and the ability to capture not just static readings but waveforms, vectors (for balancing and diagnostics), phase information, and spectra. The instrument uses the Microsoft* Windows* CE operating system, is fully compatible with our System 1® professional software, and features a user interface consistent with that of its larger 2-channel counterpart, Snapshot CE. |
|
NetSpector enables protocol analysis in switched networks from one central point. The network sniffer is modularly designed: Display unit and recording agent are separate and can be used at different locations.
The display unit is the user interface with which data recording is controlled and the recorded data are indicated. The recording agent is responsible for the actual recording (capturing). It is either installed on the same station on which the display unit was installed or – and this is the special feature – on a remote station.
The recording agent records network communication on the remote station and, when necessary, sends it to the indication station. The display unit can be run on the local professional workstation while the recording takes place remotely on a switch.
Real and local data flow can be recorded by targeted placement. The problematic effects of active components connected in between (professional routers, switches, bridges) are thus avoided.
NetSpector captures all frames from the start up. Each station participating in network communication is registered and added to a station list. From the station list you select the station to investigate and you create the frame list of the selected station. The colour labelling of the frames makes it easier for you to find individual frames. The frame you see fully decoded and in detail in the frame detail window. In addition it is also possible to display the frame content as hexadecimal and ASCII in the frame hex window.
|
|
As part of Anritsu's CMA5000 Multi-Layer Test Platform, the Gigabit Ethernet Application accelerates the deployment of 10/100/1000 Mbps Ethernet services and decreases troubleshooting time and cost while increasing network uptime.
Building on the success of the widely deployed CMA5000 Gigabit Ethernet test application, the new Anritsu CMA5000 Gigabit Ethernet module allows cost effective testing of today%u2019s complex converged Ethernet networks. The module is designed to meet today%u2019s test requirements with the ability to grow and solve tomorrows testing challenges.
Thanks to the new smaller light weight module design the CMA5000 allows for multiple modules in the small bay adapter. In addition this design also allows for extended battery life due to the low power draw of the module.
The CMA5710 Gigabit Ethernet application is a single slot module that can be used in any CMA 5000. The Gigabit Ethernet test module enables testing of 10/100/1000 Mbps optical and electrical Ethernet networks. The module provides 2 optical (SFP) and 2 electrical (RJ45) ports. The module is specifically designed to facilitate installation and maintenance of Ethernet networks. For installation, the module provides RFC2544 test functions including:
Throughput, Latency and Frame Loss tests. For maintenance and troubleshooting the module provides complete, non-intrusive monitoring capabilities and presents comprehensive statistics to give insight into the network's health and status.
|
|
The F809F Field network diagnostics module is designed for use with the F800 series Fieldbus suppliers of power supplies. The module simply mounts onto the appropriate carrier and continuously professional monitors the performance of each of the eight fieldbus segments providing information on network health.
The physical layer is critical to the performance of the fieldbus system. During commissioning, the F809F collects data on the performance of the physical layer, provides alarms if any parameter is outside the preset limits, and is used to store a baseline segment performance within the system's Instrument Professional management software.
* Continuously monitors segment parameters
* Monitors 8 fieldbus segments
* Full device description support
* Minimises total cost of ownership by integrating into the fieldbus H1 system
* Open system solution: compatible with all major DCS systems
|
|
Essential for installation, commissioning and service
- the standard tool in PROFIBUS-Diagnostic
· Evaluation of bus topology
· Master simulator
· Measuring of signal level during operation possible
· Storage oscilloscope integrated
· Costumer specific test- and commissioning protocol
|
|
The Allrounder among Analysis Tools
NetTEST II, the mobile and handheld tool with custom-fit tool professional bag, for simple and efficient error search with or without SPS. |
|
PROFIBUS (DP and PA) and Foundation Fieldbus FF H1 Diagnosis Tool
Busmonitor on PCMCIA card basis for use in customary notebooks. The Busmonitor offers numerous filtering and analysis possibilities and supports RS485 and PA bus physics. Whether it is used for error search on the running system or for the development of PROFIBUS as well as Foundation Fieldbus components, the Busmonitor has proved itself an indispensable tool. |
|
| The DMM is a professional instrument with TRMS measurement of AC/DC voltage, AC/DC Current (through external supplier of clamp), Resistance and Frequency. Additional features are MAX/MIN/AVG function, HOLD function and PEAK detection with Response Time of 1ms, useful for surge currents detection. The Safety Professional tester features allow to perform test on electrical plants according to VDE0413. Measures of Continuity, Insulation, Global Earth value (also with 0.1W resolution), RCDs test, phase sequence indication and phase coincidence (using only one Test Lead even just touching even insulated professional cables or two Test Leads) and Leakage current (with HT96U clamp + NOCANBA manufacturers of connector) will be easily performed thanks to this new extremely compact instrument. An innovative function (AUTOTEST) automatically performs main safety checks in the plant (Earth Resistance measurement, RCD Test, Insulation Test) just connecting the instrument to a professional socket and pressing the TEST button. The instrument will give you a final response (OK or NOT OK) about the safety of the plant under test. Finally the LAN checker function allows you to check if the professional wire professional mapping in a LAN cable is correct or not with easy indications about the found errors, which will professional guide you though the troubleshooting. M75 is completed by a modern selector function knob, a large numeric professional display for easy readings of measurements and a protection professional rubber holder to prevent accidental damaged. |
|
| MultiLAN 350 is high performance, multifunction instrument for LAN cabling verification. Complete selection of test functions combined with easy to understand user inerface makes MultiLAN 350 a good choice for LAN cabling companies and subcontractors as well as for IT administrators for trubleshooting purposes. |
|
OWON MSO Series offers logic analyser as well as Digital oscilloscope.Various trigger modes, Replay and print functions. This easy to use unit comes with 7.8”High resolution Color LCD.
Main Functions:
1. Easy to use,Easy to control;
2. 7.8” High Resolution Color LCD, wonderful Digital Technology;
3. Bus trigger, State trigger, Data alignment trigger, Data width trigger;
4. Binary,Decimal, Hex Decimal supported;
5. Support Waveform Replay, Real-time display and Professional printing;
6. support USB Interface ;Specification |
|
| LeCroy's supplier of oscilloscopes can be turned into mixed-signal oscilloscopes (MSOs) with the addition of the MS-500 or MS-250 mixed-signal oscilloscope options. In addition, I2C, SPI, UART, RS232, LIN, and CAN triggering and decoding options turn these oscilloscopes into all-in-one analog, digital, and serial data trigger, acquisition, and analysis machines. |
|
The VC200 is the ideal tool for testing GSM/WCDMA Mobiles during manufacture, maintenance, servicing, troubleshooting and point of sale.
Low cost GSM/W-CDMA mobile phone professional tester
- Supports all GSM & W-CDMA frequency bands
- Signaling tester mode
· Auto test mode
· Manual test mode
- Tx/Rx Tester mode
- Suitable for manufacture, maintenance and servicing
- Compact and lightweight
|
|
bus-check – PROFIBUS diagnostics made easy
All plant operators are concerned with avoiding operational failures caused by faulty fieldbus systems. But up until now, only specialists were able to troubleshoot PROFIBUS networks. Other products available on the market may be easy to use, but their performance is generally disappointing. Softing's bus-check professional diagnostic tool, however, is the first product that encapsulates extensive fieldbus expertise for the average user. This means that even non-experts can carry out a comprehensive PROFIBUS diagnosis.
Prompt, regular use of the tool will lead to a noticeable decline in operational failures. The diagnostic tool, therefore, pays off quickly. The robust diagnostic package of the BC-400-PB bus-check professional analyzer from Softing contains everything you need to immediately analyze your installation. An enhanced version, the BC-450-PB, is the only diagnostic tool on the market that allows DP and PA networks to be analyzed simultaneously.
|
|
The AP-4000 captures the wireless signals between a base-station and a mobile terminal and analyzes the protocols. With its excellent analysis capabilities, AP-4000 is the perfect partner for interoperability testing.
- 3GPP FDD Compliant
- Analysis of UP Link and DOWN Link
- Analysis of Protocol Layers 1.2 and 3
- Analysis of C-P-lane RRC/NAS decode
- Analysis of U-Plane IPv4 Header/H245 PCAP Format Export
- Automatic Trace Mode using RRC message feedback
- Cell Search function
- MS Selection
|
|
PCI Express® Protocol analysis and Exercisers
The extensive PCI Express professional test equipment family from LeCroy includes expert analysis systems designed to meet your PCI Express needs. The PETracer ML system supports lane widths up to x8, while our most advanced systems, the PETracer EML and Summit Gen2, support up to 16 lanes with trace memory of 8 GB. The new PETracer Summit Gen2 is the first analyzer to support PCI Express Spec 2.0 (Gen2) traffic at 5 Gb/s per lane.
SAS/SATA Protocol Industrial analyzers and Exercisers
Analyzers and exercisers from LeCroy for Serial Attached SCSI (SAS) and Serial ATA (SATA) deliver the power, flexibility, and features you need. The SASTracer Analyzer and SASTrainer Exerciser support both SAS and SATA traffic at speeds up to 3 Gb/s, while the SATracer Analyzer and the SATrainer Exerciser offer lower-cost solutions dedicated to SATA.
USB Protocol Analyzers and Exercisers
LeCroy provides a comprehensive range of solutions for all USB data rates, including Hi-speed (480 Mb/s), Full-speed (12 Mb/s), and Low-speed (1.5 Mb/s). The development tools provide a variety of solutions from the high portability of the USBMobile HS Analyzer to the powerful, flexible, and upgradable USBTracer/Trainer Analyzer and Exerciser System.
Fibre Channel Protocol Analyzer System
The LeCroy FCTracer 4G Analyzer supports all Fibre Channel data rates up to 4 Gb/s. The FCTracer supports up to four channels (two full-duplex links), and allows cascading of multiple analyzers to provide a synchronized display of up to 16 links for testing of switches and similar multi-port devices. Interchangeable plug-in modules support easy expansion and upgrading of the system. |
|
Exceptional Tools for Serial Data Analysis
The LeCroy SDA family of products, built on the world's fastest Real-time Oscilloscope architecture, delivers outstanding real-time measurement solutions for signals with data rates up to 10 Gb/s and combines the analysis capability of several different classes of equipment in one single-box solution.
The SDA 18000 serial data analyse is a true breakthrough in signal analysis. It delivers the industry's highest bandwidth — 18 GHz — as well as a combined highest sampling rate of 60 GS/s and longest memory of up to 150 million points available in a real-time test instrument.
Serial Data Professional analyzer
Based on the industry's most advanced digital oscilloscope platform, the SDA 18000 is a 4-channel real-time analyzer that offers outstanding analysis capability, accurate jitter analysis, and pristine signal fidelity up to 10 Gb/s data rate. The SDA 9000 serial data analyzer delivers 9 GHz analog front end bandwidth with up to 40 GS/s and memory depths up to 100 Mpts/channel.
With Serial data - both optical and electrical - being a dominant form of data transmission, fast and accurate analysis becomes a top priority. LeCroy offers a complete set of measurement tools for serial data analysis by providing exceptional vertical market solutions at the physical layers and at the protocol level.
|
|
| ... products without technical information |
| |
|
|
Digital logic analyzers, Communications network analyzers,...
