|
|
| Products 91 to 120 of 181 |
The DRILLMASTER 100 Series was designed and manufactured to meet the toughest mining environments. Featuring a Clark Power Shift transmission with 3 forward and 3 reverse gears this jumbo travels the mine with ease. Boasting an overall width of only 1321 mm it is capable of drilling in narrow vein headings as well as large headings due to its boom coverage.
For ease of maintenance and repair the DRILLMASTER 100 Series was designed with the mechanic in mind, providing easy access and removal of all components.
|
|
The DRILLMASTER 150 series was designed and manufactured to meet the
toughest mining environments. Featuring a Clark power shift transmission with 3 forward and 3 reverse gears allowing the drill rig to travel the mine with ease.
It is a completely equipped, high capacity drill rig for small sized tunnels and
mine production.
For ease of maintenance and repair the DRILLMASTER 150 series was
designed with the mechanic in mind. The design provides for easy access and removal of all components and hydraulic pumps.
The unit is fitted with RDH'S own unique Drill Control Manifold which features some of the newest hydraulic technology available.
The DRILLMASTER 150 series is a self contained drilling rig with an onboard
compressor and air mist drilling system.
Featuring a solid frame, unlike other single boom jumbos that lack in stability and are unable to operate on uneven surfaces or conditions.
|
|
Robofore, fully computerized drilling jumbos
Robodrill manufactures on request new multiple boom Robofore Jumbos.Our Robofore integrates following :
- CAT 980F Carrier (Alt. : Carrier - Heavy Construction Type Wheel Loader)
- BUPEC robotic drilling booms
- HC107 MONTABERT drills
- MONTABERT feed and drilling regulation system
- MONTABERT computerized drilling system.
|
|
Pantofore, manually operated drilling jumbos
Robodrill manufactures on request new Pantofore Jumbos.These Jumbos integrate following :
- Standard available carriers or special design
- BUC universal drilling booms
- MONTABERT drills, feeds and regulation system
- Manual or Semi Automatic drilling controls.
|
|
|
|
|
|
Rock Drilling Jumbo Introduction
Among the development and research of the products, Sunward Intelligent independently researches and develops the key technologies of the control system, hydraulic control system and special mechanism of hydraulic rock drilling jumbo, which reaches the advanced level in the world. As the latest product in China, it has been included in the National Construction Machinery “15” Development Direction List. In the past, China relied on imports totally for this product, and this project effectively breaks the situation that the imported products dominate the market in the field, meanwhile it is of great significance to promote national development of large-scale construction machinery and improve technical tunnel excavation of China.
Rock Drilling JumboFeatures
·Telescopiform structure and lifting operator's cab. Ample space for loader to pass for discharging that minimize additional workload.
·High positioning accuracy, high drilling speed(up to 1.5-1.8m/min). less drilling bit wear.
|
|
Self-propelled Drilling Truck is a one working station, one extension arm, for drilling shot holes at underground headings of methane-free mines that mine non-ferrous metals ores and/or mineral raw materials.
The working system of the drilling rig is equipped with telescope extension arm of RWP type and telescope drilling frame with a hammer hydraulic drill.
Drilling rig is equipped with a cabin that ensures protection for the operator seating there; the protection against collapse during vertical stroke with the energy of 60 kJ.
Good stability and relevant power transmission system enables the use of the said machine to exploit deposits at headings with the longitudinal grade of (in the traffic direction) to 15° and at headings with across grades to 5°.
|
|
Track-mounted DH-DC1 (BTRK) 1 drill jumbo
The track-mounted DH-DC1 (BTRK 1) drill jumbo with telescopic drill boom is intended as a universal machine for high-performance drivages in medium section roadways. The crawler base also allows the machine to operate on steep gradients.
|
|
|
Atlas Copco Boomer is a range of high-capacity drill rigs providing the best overall economy, production capacity and well-proven reliability. The Boomer range can meet all your demands from 6 to 206 m2 coverage area. The unique Atlas Copco boom system offers outstanding flexibility and precision to ensure straight-hole drilling performance in high-quality tunnelling and drifting for mine development and production. An extensive range of rock drills is available from 16 kW up to 30 kW impact power.
|
|
TD75 Electric/Hydraulic Drill
The TD75 was designed to install micropiles inside and around buildings, bridge footings and shafts. Powered by a 50 HP electric motor the TD75 uses rotary heads or drifters with torques up to 10,000 ft/lbs. The mast can be made to any height, accommodating even the most difficult access.
The rubber tracks utilize a unique scissoring design to open and close, this action allows the TD75 to close to an amazing 29.5 inches. Expanding out to 49.5 inches when drilling.
Electrical power to the TD75 can be supplied by a minimum of 75kW generator or by a 440 electric panel supplying 60 amps. By only using the single electric cable the TD75 is much more convenient to maneuver is tight spots than with rigs using a bundle of hydraulic hoses.
|
|
|
|
|
|
MP250 Man-Portable
In our effort to supply the foundation contractor with a versatile drill that could install foundation elements, as well as man-portable, TEI began manufacturing the MP250.
Everything about the MP250 makes this drill the best for those impossible places to get a hole. Look at some of these features:
* Aluminum mast can be cut to any length.
* Can use either the TE250 drifter or RDS250 rotary.
* Optional single hydraulic foot clamp.
* Control valves are removable, and can operate from a distance.
* TE250 drifter can install up to 40mm hollow bars.
* Drifter and rotary head use the same mounting bracket.
* Rotary head can turn up to a 4-inch down the hole hammer, or 6-inch augers.
* The MP250 and the MMC250 use the same ACF feed system.
* The MP250 makes a good lightweight basket drill.
Separate gas or diesel units can supply power, or the MP250 can also get its power from a skid steer loader.
The MP250 is the perfect drill to get into those places you thought were impossible to get a hole. Please call someone at TEI today and ask how this versatile tool can be adapted to solve your next very limited access job.
|
|
MINIPILING DRILL RIGS
HBR 203 - Technical Data
- Engine power: 141 kW
- Width of crawler: 740/1200 mm
Mast:
- Stroke of rotary head: 1040/2290 mm
- Extraction force: 60 kN
- Crowd force: 38 kN
Clamps:
- Diameters: 68 ÷ 230 mm
Rotary head:
- Torque: 26,6 Nm
- Drilling speed: 58 rpm
Weight:
- in working condition: 5200 kg
- Weight of power pack: 2600 kg
|
|
MINIPILING DRILL RIGS
HBR 205 MP - Technical Data
- Engine power: 147 kW
- Width of crawler: 2500 mm
Mast:
- Stroke of rotary head: 4700 mm
- Extraction force: 200 kN
- Crowd force: 100 kN
Clamps:
- Diameters: 89 ÷ 406 mm
Rotary head:
- Torque: 50 kNm
- Speed range: 62 rpm
Weight:
- in working condition: 17200 kg
|
|
|
The DRILL 650 unit is the powerful medium size rig suitable for multi-directional drilling operations. The machine is designed for soil consolidation applications, micro-piling operations, anchorages, core drilling and jet grouting.
|
|
20R Double Power Heads GSHPs Crawler Drilling-rig
The geological equipment, 120R Double Power Heads GSHPs Crawler Drilling-rig is designed to make vertical and slope bores using the following drilling techniques and methods:
-- Dry auger drilling
-- Flush rod drilling
-- Casing pipe drilling
-- Percussion deepening
-- Micro-pile injection
-- Mud circulation drilling
-- Reverse circulation drilling
|
|
Micropiles - Anchors - Jet Grouting
Micropile crawler mounted rigs allowing the execution of small holes and various technologies.
Base unit versions:
- crawler
- skid
- wheels
- decauville
- trucks
Hydraulic equipment for the execution of:
- injection
- tie-backs
- micropiles
- soil investigation corings
- jet grouting
- anchors
Drilling systems:
- down the hole hammer
- top hammer
- air/air + water
- with casing
- continuous flight auger
- jet grouting
|
|
|
|
|
|
Futuro is the drilling rig with the best compromise of compactness / power / weight, in the world market.
Use
Futuro was specially designed for underpinning works (micropiles, (jet) grouting drilling, small soil investigations, water-well drilling, static compaction) with the classical drilling methods (destructive drilling, coring drilling, auger drilling, top hammer drilling, bottom hammer drilling).
Futuro can go through house doors of 29.7 inch wide, or can drill under 87 inch ceiling heights.
Versatility
Futuro can be equipped with masts for rods from 1 to 2 m long, with various rotation heads allowing drilling holes in many cases. Futuro can drill holes with 20° obliquity or drill vertically on the corner of the machine with lateral displacement of the mast.
Performance
Ground depending, Futuro can drill up to the following depths (indicative values) :
Bottom hammer :245 ft,
Destructive drilling : 165 ft,
Rock coring drilling : 82 to 195 ft (86 mm), or 265 ft (66 mm),
Auger drilling : 100 ft.
Safety
Futuro has been designed with the last safety technologies with the passive system of emergency stop. This system instantaneously stops all the moving functions of the machine (rotation, translation of the head, hammer), without voluntary human intervention. Futuro is also equipped with a portable control panel for the translation functions of the machine.
|
|
|
|
|
|
TD75 Electric/Hydraulic Drill
The TD75 was designed to install micropiles inside and around buildings, bridge footings and shafts. Powered by a 50 HP electric motor the TD75 uses rotary heads or drifters with torques up to 10,000 ft/lbs. The mast can be made to any height, accommodating even the most difficult access.
The rubber tracks utilize a unique scissoring design to open and close, this action allows the TD75 to close to an amazing 29.5 inches. Expanding out to 49.5 inches when drilling.
Electrical power to the TD75 can be supplied by a minimum of 75kW generator or by a 440 electric panel supplying 60 amps. By only using the single electric cable the TD75 is much more convenient to maneuver is tight spots than with rigs using a bundle of hydraulic hoses.
Think about a TD75 next time you have a limited access micropile job. The options available allow it to be tooled for most any drilling application. Drifters, Rotary heads, Double Rotary Heads combined with either single or double foot clamps can install most all of today's foundation solutions.
|
|
TERRA MINI-JET MJLV 1400
• 8 tons thrust and pullback force
• maximum drilling lengths up to 120 m
• bore channels up to Ø 260 mm (depending on ground conditions)
• drill rods 1.5 m long
• bending radius 25 m
• extremly powerful with the new chain drive with no power losses at low speeds
• recommended hydraulic power 40 - 60 l/min at 175-235 bar
• equipped with ADBS (Automatic Drilling and backreaming System)
• ideal starting pit dimensions: 2.55 m long, 1.30 m wide, 0.30 m deeper than the drill axle.
• surface launch possible with optional accessories
• weight: 430 kg
• length: 2.30 m
• width: 0.60 m
• height: 1.15 m
• locating depth: 10-16 m (depending on the sonde)
|
|
|
|
|
|
Hydrostatic Pile Driver Introduction
As a kind of large green foundation construction equipment with Chinese characteristics, Sunward Intelligent ZYJ series of hydrostatic pile driver features no vibration, no noise, high efficiency and energy saving, fast pile driving and pile with high quality. It adopts seven national patent technologies such as multi-point equal pressure piles folder pile body and corner piling devices, which are of the leading international technical level. The company is the model of achieving original innovation and sustained innovation. In 2004, Sunward Intelligent won the second place in National Scientific and Technological Progress-the best award of Construction Machinery Industry that year. The product ranges from 80 tons to 1,000 tons, with nearly 30 models in total. The market has reached more than 800 units, and its market share is going ahead. Titled with famous brand of Hunan province, the products travel far to Hong Kong, Vietnam, Burma, and other countries and regions.
|
|
As the name suggests, foundation machines are used to build supporting pillars that make up the foundations of a building. Piles are broadly categorized into cast-in-place piles and ready-made piles.
We offer earth drills for cast-in-place piles, and pile drivers for ready-made piles.
|
|
B105 NG - Technical Data
- Max depth: 38 m
- Max diameter: 1300 mm
- Max depth C.F.A.: 17 m
- Max diameter C.F.A.: 600 mm
- Engine power: 147 kW
- Width of crawler: 2500 ÷ 3600 mm
- Shoes width: 600 mm
Main winch:
- Line pull: 105 kN
Auxiliary winch:
- Line pull: 45 kN
Crowd:
- Extraction force: 140 kN
- Crowd force: 90 kN
Rotary head:
- Torque: 100 kNm
- Drilling speed: 42 rpm
Weight:
- Weight in working condition 30000 kg
|
|
C800 HT H50
- Max depth: 87 m
- Max diameter: 2200 mm
- Max depth C.F.A: 34 m
- Max diameter C.F.A: 1600 mm
- Engine power: 440 kW
- Width of crawler: 3500 ÷ 5000 mm
- Shoes width: 1000 mm
Main winch:
- Line pull: 250 kN
Auxiliary winch:
- Line pull: 110 kN
Crowd:
- Extraction force: 400 kN
- Crowd force: 400 kN
- Stroke: 14000 mm
Rotary head:
- Torque: 545 kNm
- Drilling speed: 9 rpm
Weight:
- Weight in working condition: 125000 kg
|
|
|
|
|
|
Median is a powerful, robust, very complete hydraulic drilling rig with innovating kinematics, alone in the world, patented with an intuitive approach.
Median is able to drill in all positions for the most demanding clients.
Use
Median can drill all work types : tunnels, anchors, ground nails, water-well drilling, micro-piles etc… Median can drill with all method types : bottom hammers, top hammers, rollers, coring, augers, up to 500 ft deep, in all azimuth.
Versatility
Its kinematics makes the rig very versatile, and the erection on a hole is very easy and quick. Median can be equipped with an inboard injection pump to obtain better performance, and with an articulated boom to put rods on the drilling axle. A diesel-electrical unit allows working in tunnels with very minimal pollution.
Performance
Median can be in position above a hole to drill, 3 times quicker than a conventional articulated rig. So it increases the industrial drilling rate a lot. Rotation heads are powerful to drill all types of ground.
Safety
Median is equipped with an articulated control panel which can be at the left or at the right, and with one portable control panel for the translation functions. Median is equipped with passive emergency stops in order to instantaneously stop all the moving functions of the rig, without voluntary human intervention.
|
|
|
WIRTH supplies these drill rigs for special civil engineering in a series with torque levels from 140 - 400 kNm. The machines are mounted on a crawler chassis. Characteristic of all WIRTH rigs is that they can be transported complete with drilling mast. This is an advantage in terms of high mobility and short set-up times. Typical areas of application for these rigs are pile foundations by the dry boring method, the construction of secant pile diaphragm walls, CFA, partial and full displacement boring.
|
|
ImpactorHL-1800
Features:
- Compact machine
- Robust and reliable machine
- Low weight of 7000 kg
- High speed winch generates approx. 35 hits per minute
- Suitable for augering, hydraulic impact hammer and
displacement drilling as well
Advantages:
- Low ground pressure
- Working in low headroom area's (min. 2700 mm)
- High trade-in value
- 100% perfects piles
Benefits:
- Up to 50% increased productivity
- Up to 40% less labour costs
|
|
Lawn plows from Vermeer are built to stand up to rugged use, while retaining maneuverability, easy operation and low maintenance. With flexible power options, intelligent controls, adjustable plow blades and cutting-edge designs, Vermeer lawn plows match your work needs.
Lawn plows from a trusted source for trenching equipment.
|
|
|
Atlas Copco's range of surface crawlers raises the quality of rock drilling to a new level. The lowest cost per tonne of rock produced comes from the higher productivity; straighter holes and better overall economy are designed into the range. These surface crawlers include several models that are ideally suited for bench drilling. Choose between hydraulic top-hammer, Atlas Copco's patented COPROD® system, or down-the-hole drilling methods. The unique SmartRig™ will help you to drill smarter holes with high shift capacity, low energy consumption, and innovative modules that improve productivity. Atlas Copco's range of crawlers is setting new standards for stability, maneuverability and safety in quarries and contracting work.
|
|
|
Atlas Copco offers a wide range of pneumatic top-hammers for mechanized drilling. Choose from a selection that includes simple reliable rifle bar rotation machines and state of the art, powerful air and lube-oil efficient rock drills.
|
|
Trencher - 3 point-mounted: DECTRA 600
- Tractor power: 70 up to 130HP
- 3-point linkage n°2
- PTO: 540rpm
- Slow recommended forwarding speed:600 up to 800m/h.
- Important: Slow speeds are necessary for working at 60cm deep in hard soills (Tractor forwarding speed from 200m/h up to 1Km/h)
- Transmission with clamp 1¾ inch,with 6 fluted rollers on ditching device 1'3/8 inch and 6 fluted rollers on tractor's side.
- 2 hydraulic dual-way circuits are needed on the tractor for controlling the lowering of the rotor and the openning of the rear hood.
- Total weight of the ditching machine: 1 500kg.
|
|
|
|
|
|
Astec TF300B
This 18.5 horsepower mechanical trencher is a favorite for footing and flush trenching, as it can trench right next to the side of a house or other building. This model is available with steel or rubber tracks.
Astec Maxi-Sneaker Series D
The Astec Maxi-Sneaker Series D is the most popular drop plow in the world. It delivers 37 horsepower with a fthree-cylinder, liquid-cooled diesel engine. Hydraulic power steering allows unit to articulate a full 28-degrees to the left or right of center for minimum inside turning radius of 72 inches (1,829 mm).
Astec RT360
This is a powerful, but compact, trencher with a 30-horsepower Deutz air-cooled engine. It can dig trenches to depths of 60 inches. The operator can use the backhoe or trencher attachment without having to leave his seat. The backhoe can carry 1000 pounds.
Astec RT460
This trencher is equipped with a 37 horsepower Kubota engine with a rigid-frame. The only trencher in its class to feature a full-floating axle design to withstand heavy loads for long life, it can dig to depths of 60".
Astec RT560
This very popular trencher comes standard with a six-way blade, Outboard planetary axles, a heavy duty fly wheel trencher, four wheel steering, and four wheel drive.
Astec RT660 II
Built for performance, the Astec 660 II has a 75 horsepower engine and a limited slip differential to boost traction. It has a heavy duty radiator for high capacity cooling.
Astec RT960
This 99.5 horsepower trencher consistently outperforms and out maneuvers all other hydrostatic trencher models.
Astec RT1160
The exciting design of the RT1160 reflects Astec’s vision for the future of its utility trencher lineup.
|
|
|
|
Drilling, Pile driving, Trenching machines
