|
|
The MAHLE oil mist collector unit LGA 600 is a high performance oil mist collector unit for the separation of coolant from tooling machine exhaust air.
|
|
Ventilating Industrial filters up to 225 gpm, L1.0406/L1.0506/L1.0706/L1.0807
Application area
Ventilation of tanks for hydraulic and lubrication systems, and gearboxes.
General
The oil levels in the tanks of hydraulic systems are subject to continuous
variation due to temperature changes and the operation of cylinders and
pressure vessels.
In order to prevent over pressure in the tanks, an exchange of air with
the external atmosphere is necessary. By the use of a ventilating filter, the
outside air that is drawn in is filtered and the ingress of dust is therefore
prevented.
Special features
The ventilation openings are designed so that dust on the surface of the
professional tank is not drawn in, and that the ingress of spray and rainwater is largely
prevented.
The use in marine applications presents no problem due to the use of
synthetic materials and stainless steel.
Design
Flow direction bi-directional (air IN/OUT). The star-shaped pleating of the filter material results in:
- large filter surfaces
- low pressure drop
- high dirt-holding capacities
- long service life |
|
Air breather professional filters allow for the flow of clean air to and from a closed chamber where balanced atmospheric pressure is required, such as in gear boxes, manufacturer of bearings operating at high speed and hydraulic power packs.
Filton air breather filters ensure that there is no dangerous build up of pressure or vacuum due to temperature or volume changes. The high quality sintered element prevents the ingress of air borne foreign particles. |
|
MAHLE crankcase ventilation systems reliably clean the gases contaminated with oil mist from the crankcase. The oil consumption can therefore be reduced further and the emission limits fulfilled. The oil mist separator integrated in the crankcase ventilation serves to separate the gas and fluid components. The separated oil is then returned to the oil circuit and the cleaned air supplied to the intake system.
|
|
TMDFL :
- Filler breather with large breather, professional filter and labyrinth overflow protection
TMD/TMDF/TMDF-BR :
- Filler breather with double breather hole
- Filler breather with double breather hole and filter
TMDF/AL :
- Round headed filler breather, with vertical ribs for better grip
TMDV :
- Filler plug with one way air vent cock
TSF :
- Filler breather with filter
TSV :
Filler breather with checkvalve
TP/TPF/TPV :
- Press-fit filler breather with large breather hole
- Press-fit filler breather with large breather hole and filter
- Press-fit filler breather with air relief valve
TPB/TPBS/TPBSF :
- Low profile plug
- Low profile plug with brather and dipstick
- Low profile plug with breather, filter and dipstick
TF :
- Filler cap with internal thread and breather hole |
|
Oil Level Dipsticks , C4.0410/C4.0412/C4.0421/C4.0431/C4.0450/C4.0464
Application
Controlling the oil level in hydraulic oil or lubricant reservoirs
Construction and function
ARGO-HYTOS oil level dipsticks are robust semicircular metal rods with an O-ring professional seal.
A mounting bolt with a suitable hole is supplied with each dipstick. Dipsticks are available in various lengths, with various markings, and with various mounting bolts specifications (see selection chart).
Special features
- The robust material withstands even the most severe operating conditions
- The integral O-ring provides a 100% tight seal
- A suitable dipstick mounting bolt can also replace one of the mounting bolts of an in-professional tank return or suction filtering
Mounting
The bolt supplied with the oil level dipstick is installed either in a separate threaded hole or in an already existing mounting hole for an in-tank professional filter. This eliminates the need of an extra mounting hole. If used as a filter mounting bolt, care should be taken to provide a proper seal between the tank, the filter and the mounting bolt. |
|
A full range of industrial filters for corrosive liquids:
- Made with corrosion-resistant plastics
- exclusive L-TECH pleated cartridge filtration system
- Filtration area up to 40 m2
- Filter gauge of 50 to 1 micron
-TECH pleated cartridges:
designed and manufactured by SIEBEC, this high-capacity cartridge (180 mm diameter) fits as standard to SIEBEC L and P filters and covers a wide range of industrial applications.
Extruded Polypropylene Cartridges
Polypropylene Coil Cartridges
Paper filter discs |
|
- Professional tank top mounting.
- Connection ports 3/4"+3/4", 3/4" 1" or 1 1/4" 2x1".
- Nominal flow rates up to 200 L/min.
- Max working pressure 1 MPa (10 bar).
- Standard professional filter media: FC, SA, FD, CC, CD.
|
|
Vertical Professional filter Separator
The Plenty Vertical Filter Separator will remove 100% of all droplets 8-10 microns and larger and 99.5% of all droplets ½-8 microns in size.
It will also remove 100% of all solid particles, 3 microns and larger 99% of all particles ½-3 microns in size.
These operating efficiencies apply over the entire flow range from maximum design down to virtually zero flow.
The first stage of the filter separator consists of a number of glass fibre coalescer /filter elements through which the wet gas passes.
The small liquid drops carried in the gas stream are trapped within the glass fibres of the element and coalesce to form drops 100 to 200 times larger than the original size.
These drops pass through the element wall and are carried forward by the gas stream to the second stage vane type separator.
The second stage consists of a vane type impingement separator, which operates exactly as described for vane separator.
|
|
BELL In-line Professional filters grant a high protection to the most delicate components of an oleodinamic system. Placed in the site under pressure, they keep the particles sucked or produced by the pump up to a size of 10 micron.
These filters are normally applied in addition to the standard filters in suction or release, as a last barrier of protection before the entrance in directional cocks, flow regulating valves and all those components which require a high grade of absolute filtering.
The body is made in a treated aluminium alloy to obtain a minimum dimension and weight.
The filtering element, instead, is made in synthered bronze with a conic shape to resist to high pressure without collapsing. |
|
Application
Hydraulic oil and lube oil
Model / design
In-line professional filter 250 and 450 LE
for direct installation in a pressure pipe
Flange filter 250 and 450 FE
For direct mounting on a control block
Pressure. 450 bar max.
Flow rate: 1500 l/min max.
Connection:
Up to 2 ½’’, depending on filter size
Filter elements / cartridges
EPE standard elements
EPE filter elements according to DIN 24550
Further series up to 10.000 l/min
|
|
High Pressure Single Strainer - Simplex T Type
The Simplex T Type extends the range of S type professional filters to higher pressures, suitable for both liquid and gas applications and available with bolted or quick release type covers.
Standard Features
Quick release covers eliminate the need for tools for maintenance.
Designed for pressure ratings up to ANSI class 300lb (900 PSIG).
Flow is from inside to outside the basket to trap and retain debris.
High basket area to pipeline CSA ratio of over 10:1 in most cases.
Can be fitted with coarse perforated baskets (2mm as standard) or fine stainless steel mesh inserts to give particle removal down to 50 microns.
Disposable depth type cartridges are available for filtration to 5~10 micron for liquid and 1~2 micron on gases.
|
|
ILF-200/ILF-201 "Vortex" Professional filters
- High Pressure Industrial liquid filters
- Max 690bar Pressure
- Minimum 25µm filtration
- Strong re-usable elements from 316 wedge
- High flow capacity
- Oprional back flush and drain facility
|
|
98 Series Industrial filters - High Pressure (10 micron)
98-1110 Series T-Type Filter:
Designed for high flow applications
Features cleanable element
Available options: electrical, visual, bypass cock, visual pressure differential indicator, bypass relief valve, electrical bypass |
|
Type ABZFD...-DIN
Pressure filters acc. to DIN 24550 for installation in pressure lines:
- Professional filter elements based on inorganic fiber
- Adsorption of finest particles over a wide pressure differential range
- High contamination retention capacity due to large specific adsorption surface
- High bursting strength of filter elements (e.g. in the case of cold starts)
- Filter ratings 10 µm and 3 µm absolute
- Mechanical visual and electrical clogging indicators
Type ABZFR...-DIN
Return flow filter acc. to DIN 24550 for direct professional tank installation:
- Filter elements based on inorganic fiber
- Excellent separation characteristics (-values) over a wide pressure differential range
- High contamination retention capacity due to large specific adsorption surface
- High bursting strength of filter elements (e.g. in the case of cold starts)
- Filter ratings 10 µm and 3 µm absolute
- Mechanical visual and electrical clogging indicators |
|
Industrial filters
Line-type: filter for petroleum base fluids featuring spin-on throw-away cartridge. Rated to 200 psi. Standard return line installation with bypass relief. Suction line models also available. Condition indicator optional. 10 or 25 micron elements.
|
|
Application
Hydraulic oil, lube oil, cooloing agent
Model / design
In-line professional filter 40 and 160 LE
for direct installation in a pressure pipe
40 LE 0020 and 40 LE 0030 with quick lock
Pressure. 160 bar max.
Flow rate: 500 l/min max.
Connection:
Up to thread 1 ½’’,
Filter elements / cartridges
EPE standard elements
EPE filter elements according to DIN 24550
Further series up to 450 bar or 10.000 l/min
Please visit our homepage http://www.eppensteiner.de
|
|
HYDRAULIC FILTRATION
Olaer partner MAHLE for 20 years, has proposed a complete range of industrial filters for hydraulic systems.
Low medium and high pressure, suction, switched double filters, partial flow filters, return, Spin on cartridges
A solution of filtration for:
- to increase the efficiency of the components
- to reduce the costs of maintenance
- to reduce the downtimes machine
- to preserve the environment
|
|
"BNF Off-Line Professional filter
Compact design
Easy installation
DIN filter elements
Easy replacement of filter element
Filling function optional (BNF 18 / 30)
Low-noise gerotor pump" |
|
| The pressure line filter is an essential part in most hydraulic systems. When the hydraulic components are sophisticated, with close tolerances and a regulation function (not simply that of control) the use of professional filters in the pressure lines is a must. |
|
Return-line industrial filters retain all the contamination created within the equipment and flushed out of the hydraulic circuit, thus preventing contamination entering the circuit via the professional tank and pump, with all its negative implications.
|
|
| The return line professional filter is an essential part of any hydraulic system. In many instances it is the only "system protection" provided and therefore must be carefully chosen to ensure maximum system efficiency. |
|
"Over the years the Fluidcotrolterminal has taken a very significant role in condition monitoring of fluid power systems.
Based on the experience with this combined unit, Bühler is introducing a more advanced product with a greater integration of functions.
The Multiterminal integrates the function of a tanktop return-line professional filter with advanced two stage capacity monitor and as an option, an automated filling port.
The design allows for very flexible adaption to individual application. The Multiterminal consists of a cast aluminum baseplate with integrated return-line filterhead. The head offers three different G 1 inlet ports situated 90° and in addition an G 1/2 filling port. There is also provision for a cartridge tap where automated filling is required. Two sample ports are provided for alternate use plus one sample port in the return line.
The base plate has an interface flange to DIN 24550/T2. The flange can take any suitable breather filter or can be equipped with Nivovent units from either series 7 or 8. These units feature a qualified breather filter with integrated level controls and temperature display plus controls as an option.
combination of: breather, level- and temperature control, return-line filter with capacity indicator, sample ports for reservoir and return line, filling port and filling control by a 2/2- way cartridge cock
return-line filter for filter elements according to DIN 24550
international standard flange DIN 24557, part 2 integrated in base plate
compact dimensions
easy installation
modular design
automated filling" |
|
Series SR
Professional filter Aspiration-Return now available with elements LEIF®
Technical description:
Conceived for the mobile equipment with loop closed for the hydrostatic transmission and an open hydraulic system
Oil return of the open system and aspired oil of the closed loop thus filtered by only one unit
Food under positive pressure of the oil of return filtered coming from the system open to/the pump (S) of cramming of the hydrostatic transmission
Patented elements ecological LEIF® (Low Environmental Filter Impact) from now on assembled out of standard
Offer to the originators systems an optimal protection.
Advantages:
Avoid the cavitation of the pumps and extension the lifespan of the components
Improve the reliability of the system thanks to a quality of guaranteed filtration
Ecological and patented elements LEIF® reduce the costs of reject of more than 50% on average.
Applications:
- Mobile Equipment
- Handling (lifting trucks etc)
- Vehicles of maintenance (manufacturer of sweepers)
- Agricultural Materials TP and vehicles.
|
|
|
|
Hydraulic filters, Oil treatment
