|
|
Their flexibility and fast heating feature make it necessary to use the Armagnac in premises such as :
- Sales and/or storage areas
- Sports hall
- Agriculture and breeding premises
- Industrial and commercial buildings.
Over a pleasant presentation, electric aerothem Armagnac are fitted with all components and accessories allowing a quick installation, a safe and quiet operation.
- Armoured resistance
- Slow speed helicoid fan
- Power contactor
- Safety and control thermostats
- Fan timer
- On/off switch with light signal
- White RAL 9003 painted sheet steel frame, RAL 9010 lacquered deflectors protected with a removable plastic film.
Produced in 2 sizes, for power from 6 to 24 kW.
For powers from 15 kW to 24 kW only, the equipment is fitted with contactors allowing a two step operation if necessary.
|
|
|
|
|
|
Heater fans PHE and PHD
Robust, powerful and durable
For heating and ventilation of
Workplaces
Day rooms
Showrooms
Portacabins
Construction sites
or for drying of damp or moist rooms
Robust housing made of galvanised sheet-steel, coated, corrosion-resistant.
Carrying handle as tubular stand with sufficient floor clearance.
Heating elements made of stainless steel, non-glowing.
Thermal overload protection as standard feature. Switches motor off under thermal overload and comes on automatically again after cooling down.
With wall bracket
For portable or stationary operation.
High air circulation. Rapid heating.
5 power classes: from 3 to 20 kW.
Dual-walled housing offers safety.
Robust motor with ball bearings, maintenance-free
Fan and heater can be switched in 3 or 4 steps.
PHD 9/ 15/ 20 with timer: Switch-on time can be preselected up to 24 hours.
Heating thermostat with temperature range which can be set (infinitely variable) to between 0 °C - 40 °C. Fan continues to operate once the temperature has been reached.
|
|
Fan heaters of simple and robust design for heating recirculated air in areas such as workshops, factory shopfloors, warehouses, refectories, sports halls, garages, shops, greenhouse ...
Vulcanic manufactures a very large range of fan heaters, such as portable fan heaters, fan heaters with castors, and high power fan heaters for wall mounting.
|
|
To develop the more efficient electric floor heating system at the European market, At ECAS we have designed the parallel heating cable constant power: model CTCS250/15.
The CTCS250/15 deliveries a power of 15 w / m, and allows to be cut to measure, according to the requirements of the project.
To complement the CTCS250/15, we have chosen the best possible devices and accessories:
Thermostats:
. OTD2: digital thermostat "Room + Floor”.
. OCD2 1999 H1: digital thermostat "Room + Floor", with a 4 program event.
. Electric radiant floor Insulating layer: ISOLAS THERMIC.
. Mounting guides for the electric heating cables: GUIDEFASTDP-01.
. Assembly and connection kits: DPPCTCS150-250 and DPFCTCS150-250
|
|
Thalassa fan convector are reversible heating and air conditioning.
The offered range includes 4 models and 5 sizes, with powers from 5 kW cold production and 11 kW hot production.
Since there is poor residual pressure with this equipment (20 Pa), they are used preferably for direct blowing either hanging or wall mounted, with or without casing.
Easily integrated in any type of premises due to its discrete presentation and RAL 9010 epoxy painted frame.
Aircalo offers a wide scope of flow control customization.
|
|
|
|
|
|
Major 2
The Major 2 fan coil unit is designed to be mounted vertically on a wall or horizontally below ceilings to heat and cool homes, businesses and industrial and healthcare facilities. Not only does it combine the economic benefits of installing and operating a central boiler and chiller plant, it also allows individual temperature control in all rooms.
Available in six sizes and two models:
- CH: horizontal cased,
- CV: vertical cased.
Heating capacity: 2 to 20 kW
Cooling capacity: 0.6 to 8 kW
Air flow rates: 115 to 1300 m³/h
- Polymer casing with solid RAL 9010 finish,
- Two access doors lead to air bleed valve and control terminal,
- Water coil: two or four tubes or two tubes and electric heater,
- Condensate drain pan,
- Seven-speed motor (three factory-wired speeds) with balanced, double-inlet aluminium blower wheel,
- Mounting bracket frame,
- Regenerative polyester fibre filter. Efficiency class: G3 (EN 779),
- Fully enclosed electrical junction box,
- A wide selection of control options.
|
|
Floor Standing Type
This space-saving design with a slim shape and smart vent line offers the least obstruction to the surrounding area.
* The unit can be easily installed on the floor along the wall or under the window. Maintenance is simple.
* This type can be hung on the wall for easier cleaning.
|
|
This unit has function of electrical convector and fan. This allows :
- In the winter, very fast heating ( 2 stage of power : 2 - 3 KW). Homgeneity of the air temperature thanks to outlet direction.
- In the summer, ventilation only with very low electrical consumption (35W)
Compact, esthetic
Régulation on board
Wall mounting
|
|
Rectangular fin elements
Consisting of a "U" shaped element on which are crimped the rectangular fins (25 x 50 or 40 x 80) made of protected steel or stainless steel and usually equipped with threaded glands.
|
|
Mechanically-bonded continuous fin assures excellent heat transfer and helps prevent fin vibration at high air velocities.
Several standard formations and mounting bushings available.
Standard fin is high temperature painted steel with steel sheath.
Optional stainless steel fin with stainless steel or incoloy sheath for corrosion resistance.
120v, 208v, 240v, 480v available.
Maximum Sheath Temperature
750°F (400°C) - Steel
900°F (480°C) - ST.ST./INCOLY
Made in U.S.A.
|
|
Full range of heating cabinets gas or oil fired.
Available in vertical or horizontal versions, inside or outside and able of ducted appications.
Air flow from 6000 to 60000 m3/h and power from 70 to 1120 KW.
High temperature resistant steel exchanger or stainless steel.
For various cases, the body can be double skin.
Filtration optional.
Applications : Industrial buildings heating and/or ventilation with sveral kind of applications for high level confort for users.
This equipment is in accordance with European directive related to gas fired equipment 90/396/CEE under n° 49AQ1369 and 1370 and electro-magnetic compatibility CEM 89/336/CEE and low voltage 73/23/CEE.
|
|
These equipment may be connected either with vertical or horizontal vent or through a chimney.
These aerotherms do meet the main requirements of the CE standards requirement related to gas-fired aerotherm.
CAUTION :
These equipment can only be used in sufficiently aerated premises, except where a tight connection is provided.
The proper operation of the aerotherm depends on a correct installation and start-up.
Aerotherm should not be installed in :
- Hazardous areas
- Premises containing vapours of chlorinated combination
- Areas with high contents of inflammable dusts
- Highly humid rooms.
|
|
DESCRIPTION:
Gas domestic hot air generator with leakproof operation and smoke outlet through an extractor.
Its operation is completely autonomous and its function is that one of heating the environment air of the premises that must be conditioned.
The basic equipment has the following elements:
- Leakproof combustion with forced draft.
- Combustion oven designed for obtaining a performance of about 90%.
- Three-speed fan (except for the GAS-40 model, which is one-speed).
- Air admission filters.
- Environment thermostat.
- Air impulsion grid on the upper part (GAS-08-12-15).
FUEL:
Natural gas / LPG
APPLICATIONS:
Any kind of premises with a volume between 190 m3 and 980 m3.
|
|
SYSTEMA introduces the new series of EOLO, suspended warm air heaters able to solve all heating problems, both for total and modular space heating. Compared with traditional heating systems needing a separate cabinet, the new EOLO heaters offer an innovative solution for heating while keeping running costs at a minimum.
This is possible thanks to the fact that EOLOs are completely self-sufficient working units, and that you don?t need to heat up a heat transferring fluid such as water for heating the space. In this way you don't have any needless heat losses.
|
|
Hot gas generators fabricated by Unitherm Cemcon are designed for direct air heating performed by a firing system. Air to be heated is either supplied by a dilution air fan or is delivered from process with high or low temperatures or combinations of both.
Unitherm Cemcon provides:
* Hot gas generator engineering for supply or local manufacturing
* brick lining material
* Burner (mono block or special designs) incl. operation valve train and fuel supply system
* Diluton air fan
* HGG field instruments for performance and safety control
* HGG control cubicle
|
|
A RANGE OF CERAMIC GAS HEATERS ADAPTED TO ALL HEATING NEEDS IN INDUSTRIAL BUILDINGS (height of 4 meters and more).
Use: Industrial buildings, Churches, Sports halls, Car service, Terraces, ...
- a large range of heaters from 2,5 to 27 kW and more.
- a choice of 10 powers for a comfort in all type of buildings whatever the
hanging height of the heaters
- a double-speed option for a better comfort, particularly in well insulated
buildings
|
|
|
|
|
|
Ageo
High-temperature ground-source (earth or groundwater) reversible heat pump for heating and cooling of individual homes and small businesses. Built with all the necessary hydraulic components on the sensor and emitter side. May be connected to emitters that radiate gentle heat, such as underfloor heating and cooling systems, terminal units (such as fan coil units and water cassettes) or low-temperature radiators
Seven models available
Heating capacity: 9 to 36 kW
- Complete packaged unit,
- Coated, corrosion-resistant galvanised steel casing,
- ABS exterior panel,
- Free-standing inside frame separated from main frame by vibration isolators,
- Scroll compressor,
- Water-cooled brazed plate heat exchangers,
- Hydraulic module on both exchangers, with accelerator pump and expansion vessel,
- Microprocessor-based control unit with MICROCONNECT two-wire remote control.
- Inrush current limiter as standard on single-phase model, as required by French standard NF C 15 100
- Domestic hot-water tank optional.
|
|
Heating- and Cooling Units
The temperature of die is a significant factor in relation to quality of castings and efficiency of casting process.
Robamat temperature control units have been developed especially for the hardest fields of use in diecasting industry. Heating- and cooling units for a reliable heat exchange, flexible at smallest space, based on heat transfer oil or pressurized water system, designed as single- or double-circuit units %u2013 state-of-the-art technology for a perfect sophisticated circuit.
Robamat heating and cooling units guarantee:
- best possible surfaces
- narrow tolerances even at complicated shapes
- continuous quality of castings
- shortest cycle times
|
|
A range of gas-fired furnaces with 2 or 4 burners. In full compliance with applicable safety regulations.
All models are equipped with a safety valve that interrupts the gas supply if the flame is extinguished. Economical, fast and clean: ideal for versatile operations.
Typical applications: heating of metals prior to working and creation of ornamental and other products.
|
|
|
Process Heat - nyb offers a complete range of fans for the process heat industry. Whatever your needs; high temp process fans, combustion air, exhaust, custom forced-draft or custom induced-draft, nyb has a design to accommodate.
|
|
|
|
|
|
Farming hot air generator completely autonomous with heating gas oil, natural gas or liquefied petroleum gases (butane gas, propane gas) operation.
These equipments function is that one of heating the environmental air by means of the thermal energy produced by the equipment.
The produced heat is driven to the premises that must be conditioned by means of a centrifugal fan.
The combustion products are extracted through a chimney in order to ensure that the driven hot air is exempt of smokes and bad smells.
The main features are the following ones:
-Heating gas oil, natural gas or liquefied petroleum gases operation.
-Closet made with galvanised sheet.
-Heat exchanger dimensioned in order to obtain performances superior to 90%, made with AISI-430 stainless steel.
-Combustion chamber made with AISI-304 stainless steel.
-Control panel made in a watertight box for avoiding the high humidity degree in greenhouses.
-Reinforced environmental thermostat with 5m hose and fast connector included in the equipment.
-Base equipment prepared with air impulsion grid of simple deflection.
-It can have circular hoppers or any other kind of impulsion pipes coupled on it.
|
|
|
WATERSTRIPs (radiant thermal strips) are suitable for heating large industrial and civil buildings by radiation. They are the best solution where low-noise operation, no air flow, and no dust circulation is required. WATERSTRIPs are suitable to heat rooms housing inflammable mixtures without any problem. No air flow and low stratification ensure low running costs.
|
|
The company Systema SpA proposes an innovative technology for the heating system with a NEW product: THE WATER STRIPS "TS". They are used particularly to environments with fire risk' activity, for example textile industries, body shop, plaining mills, environments of public show and local with a lot of of people presence, warehouses with shelvings, environments dedicated to sporting activity and downtown.
The water strips "TS" are units that heat the space by radiantion, allowing an energetic saving, in fact the heat is directly to the people without loss of heat in the air. Please ckick here if you want to dowload the cathalogue.
|
|
Evolix EC. - Radiant panels warm water
Composed of 5 models available in 2 lengths: 3000 or 6000 Mr.
Power: from 100 to 150 W/m ² (water 90/70 °C)
Space heating of large volumen (installation starting from 3 m up to 12 m).
Industry, versatile rooms, colleges, colleges...
|
|
|
|
|
|
Innovation, activity, market oriented behaviour, those are the distinctive HITEMA characteristics, Hitema has been able to play a loading role on the international market thanks to her ability to place good technological solution for industrial conditioning, industrial refrigeration and for air compressed treatment and thanks to the preparation of a commercial net that includes professional technicians that besides carefully promote the products, provide a real consulting service to the Customer, this service is an integrant part of Hitema offer.
Water chiller with scroll compressors
ECA basic type 001÷280 kW
ECT silent or supersilent version 005÷280 kW
ECC basic with centrifugal fans 010÷180 kW
ECFS basic with free- cooling, 030÷180 kW
Water chiller with screw compressors
ECS basic R407C 230÷930 kW
ECF basic with free- cooling included, R407C
ERS basic R134a NEW!!! 245÷980 kW
ERF basic with free- cooling,R134a NEW!
Water chiller with screw compress. and very high free cooling performance
ES basic mod.with free cooling, R407C NEW! 080÷800 kW
Water chiller with screw compressors for high ambient temperature
ECSH basic mod.,R134a NEW! 195÷655 kW
Water chiller with remote condenser
ECRS mod.with scroll compressors 022÷280 kW
ECRB mod.with screw compressors 230÷930 kW
Water chiller with water condenser
ECWS mod.with scroll compressors,R407c 001÷280 kW
ECWSH mod.with scroll compressors,R134a
ECWB mod.with screw compressors,R407c 230÷930 kW
ECWBH mod.with screw compressors,R134a
Heating pump
ECH water air reversible 012÷280 kW
ECG geothermic with scroll compressors-R404a 004÷020 kW
|
|
These particularly robust appliances have been designed to provide reliable heating for industrial and technical premises, control rooms and mobile site cabins. Connection via gland to a IP55 IK7 aluminium terminal box.
Protected steel brackets and body.
available with an integral control thermostat, adjustable from 0 to 50°C.
Horizontal fitting.
|
|
DESCRIPTION:
Stove of industrial firewood with ventilator with operation to firewood, shavings, charcoal, etc.
Ideal for the heating of the industrial premises with a maximum volume of 1.075m3 to 2.150m3
FUEL:
LEÑA-BRIQUETAS-CARBÓN
|
|
DESCRIPTION:
Fully automatic domestic stoves and respectful of the environment as they use as fuel pellets (pressed wood waste).
With controlled electronic on/off and automatic, equipped with ambient thermostat, five heating powers, programmer with two daily on and off, etc.
|
|
A RANGE OF CERAMIC GAS HEATERS ADAPTED TO ALL HEATING NEEDS IN INDUSTRIAL BUILDINGS (height of 4 meters and more).
Use: Industrial buildings, Churches, Sports halls, Car service, Terraces, ...
- a large range of heaters from 2,5 to 27 kW and more.
- a choice of 10 powers for a comfort in all type of buildings whatever the
hanging height of the heaters
- a double-speed option for a better comfort, particularly in well insulated
buildings
|
|
With Watlow's diverse RAYMAX® radiant heater line, we have a solution for almost any application requiring radiant heat. Our capabilities cover a wide range of needs, from contamination-resistant panel heaters to fast-responding quartz tubes to rugged tubular elements and high temperature ceramic panels.
Applying radiant heaters can be complicated. Watlow's engineering staff has the level of training required to help you meet your application requirements, providing a high degree of technical support such as conducting testing for your application at our facility, calculating your watt density and temperature requirements, and recommending system components such as sensors and controllers. With our experience in a wide range of industries, chances are Watlow has already helped someone handle a radiant heating application like yours.
Applications
Thermoforming
Food warming
Paint and epoxy curing
Heat treating
High temperature furnaces
Tempering and annealing processes
|
|
|
|
Heating equipment
