|
|
|
The air-swept tubular dryer is a new concept in drying technology. Manufactured in the United States, it will process anything from low solids slurries to low moisture powders. The flow of material through the dryer is controlled so that the product may be a fine, dry powder or a moist granular material.
|
|
Imtech DryGenic helps the industry to produce better quality products in controlled temperature/humidity environment while minimizing utility usage and maximizing production rates.
The Imtech DryGenic dryer has the characteristics of high efficiency and low energy.
The design and the selection of the dryer is decided by the wet and the dry product flow characteristics,
lump / crust formation tendency and the thermal sensitivity. The dryer capacity and size and performance depends on the available heat transfer area and the operating conditions for the specific product. The combination of temperature cycles and drying times can be adjusted accordingly as to control the final product’s physical properties.
|
|
|
|
|
|
Vacuum belt / band driers consist of a housing with built-in conveyer belts for the product running over heating plates. Automatic belt control ensures precision belt operation. The belts run parallel to one another and a metering pump with oscillating application nozzle is assigned to each individually controlled belt.
The shift in the boiling point under vacuum provides for a low evaporation temperature and therefore gentle product temperature.
Pumpable products usually run through a highly viscous, frequently sticky phase during the drying process. This formation of vapor bubbles in the product results in a dry cake on the belt toward the end of the drying process. The temperature to which the product is subjected during the drying process has a significant effect on the achievable product quality. The belts run over a number of heating zones and over a cooling zone at the end. Steam, pressurized water or thermal oil can be used for heating; each zone can be controlled separately, allowing the temperature of the heating surfaces to be adapted to the specific requirements of the product.
|
|
After the mass finishing process, the processed work pieces are nearly almost wet and have to dry. The Trowal drier range is composed of various types.
BF-HL RANGE
Applications
Normally, the processed work pieces have to be dried after the finishing process. Trowal hot air belt-driers are designed to dry the work pieces with hot air. Most suited for components, which may not impinge on each other. For
- components with difficult to reach cavities where drying medium
may lodge
- long and bulky parts
|
|
Whether the product is a wet powder or a slurry, specially designed feeders transfer the product into the dispersion section of the dryer. A high speed rotor disperses the product in the drying zone. An induced hot gas stream as high as 600 °C provides the energy for instantaneous evaporation of the moisture within the feed material. Evaporation capacity of the largest unit is over 6000 kg/hr. Dried particles enter the classifying zone at the top of the dryer and fine de-agglomerated particles leave the dryer outlet to be collected down stream. Coarse particles are rejected by the classifier and are returned to the dispersion zone for further processing.
|
|
Drum Dryers are available in single and double drum models. Single drum units may be dip or splash fed, or equipped with applicator rolls. The latter is particularly effective for drying high viscosity liquids or pasty materials such as mashed potatoes, applesauce, fruit-starch mixtures, gelatin, dextrine-type adhesives, polyacrylamide, synthetic resins, and various starches.
Double drum dryers are the most versatile and widely applied. These dryers are used to dry many food, chemical, and pharmaceutical materials of widely varying densities and viscosities: dilute solutions, heavy liquids, pasty materials, or fairly heavy sludges. The movable drum permits complete control of product film thickness. Feed may be by perforated tube trough, pendulum, or special engineered devices.
|
|
International Surface Preparation offers the Walther Trowal line of mass finishing driers. After the mass finishing process the finished work pieces are typically wet and require drying.
International Surface Preparation offers these three series of Walther Trowal driers:
- G Series - Heated vibratory bowl style driers for stain-free drying and secondary polishing of the processed work pieces with the use of heated media. Click here for more information on the G Series.
- DLT Series - Rotary drum style driers typically used with a heated drying media. Parts are transported continuously through a rotating screen drum. Click here for more information on the DLT Series.
- BF-HL Series - Hot air tunnel belt driers. Processed parts are transported through a drying tunnel on a wire mesh belt as hot air is circulated via a blower fan evenly throughout the drying tunnel.
|
|
|
Imtech DryGenic unite dehumidification and product drying expertise and customer focused service to each application. For over 50 years Imtech DryGenic has manufactured Dehumidification systems and Drying tunnels / Belt dryers and is recognized globally for expertise, quality, service and in providing innovative solutions for complex drying processes.
|
|
The Mikro-LGM long gap mill assures superior product quality and peak operational efficiency. Built upon the strength of Hosokawa's unparalleled experience in size reduction, thermal processing and classification, the Mikro-LGM long gap mill is designed to meet the exacting demands of a wide variety of industrial applications.
|
|
|
The Atritor Dryer-Pulveriser has been in continuous manufacture for 80 years. It has a quite unique design with pulverising occurring predominantly by attrition. The mill is a very compact air-swept flash dryer and temperature differentials of over 500° C ensure high evaporative capacity and thermal efficiency.
|
|
|
Preserving of foods by drying is a very old system applied since ages which is learnt by mankind from nature.Drying systems of GOKSER MACHINE have the characteristics of convection drying systems. The difference from other convection systems is equally distributed air. With our special design, aflatoxin is prevented. For a detailed information, please contact us.
|
|
|
Key's Automatic Dryers lead our fresh-cut suite of solutions and provide the industry standard in efficient and effective fresh-cut drying. This system offers gentle handling and a simple sanitary design combined with a fully controlled and automated drying solution.
|
|
Dryer desiccator cabinet KW.86/AV Series.
Internal chamber and shelves are in stainless steel; external cabinet in brushed AISI 0 stainless steel sheet and equipped with split opening door with sealing. Heating is achieved with specific air heaters; discharge of steam inside the chamber occurs by means of centrifugal electroaspirator with 0 m³/h flow rate.
The electrical system is provided with general switch and running light signal. Thermal stability is obtained through PID digital electronic μP regulator (with RTD Pt100 OHM input); it is paired with specific SSR, suited to absorbing load of heaters. In addition, each appliance is equipped with aerators and adjustable supports for shelving.
|
|
Vacuum drying cabinets serve for basic drying of temperature-sensitive concentrates and pasty mixtures of solid substances as well as granulates.
The properties of the dry product depend on the quantity of liquid they contain and the operating parameters which can be set on the equipment.
vacuum drying cabinetThe desired requirements can be controlled and adapted to the greatest extent with the drying process.
In comparison to other types of driers, vacuum drying cabinets offer optimum possibilities for influencing the drying characteristics.
|
|
|
Industrial drying ovens of drying of 100°c with 500°c. A whole standard range of 20 liters to 2000 liters.
|
|
Monoblock Oven
* Up to 350 °C (662 °F)
* Standard line starting at 1 m3 (35.31 ft3)
* All applications: (drying, dehydration, baking, polymerisation of products with flammable substance, liquid and powder painting)
* Electronics controlled by a PLC
* Static relays or thyristor-controlled power controller
* Powered by electricity, gas, heat exchanger...
|
|
Economical electric oven SNOL 2160/220 is designed for various materials and components heat treatment under low temperature, e.g. drying, preheating and other purposes.
•Circulation fan.
•Mild steel working chamber.
•Control block separated from the oven.
•Micro processor temperature controller.
•Moving bottom cart for loading up to 4 t.
•For smaller components special shelves can be placed on the moving cart.
•Two ventilation holes on the upper part.
•Vertical flow hot air circulation.
•Powder painted exterior.
•High quality thermoinsulation materials.
•Low power consumption.
•One year limited warranty and later service.
•Two years limited warranty for temperature controller and later service.
|
|
Where autoclave curing is not required, Aeroform have perfected their precision temperature oven technology in conjunction with the control systems developed for the autoclaves, providing gas and electric ovens of unparalleled performance, to any size with temperature ranges currently up to 600°C
|
|
Explosion-proof safety vacuum drying oven for EX-Zone 2
BINDER VDL EX-Zone 2 series:
Same quality as the VDL series, but with some added safety features: The VDL series EX-Zone 2 is designed for operation in explosion hazard areas EX-Zone 2, in full compliance with ATEX requirements. Our special safety package eliminates any risk.
Find out more: www.vacuum-drying.com
|
|
Batch Drying curing Oven
Industrial tailor-made ovens from 1m³ to 200m³ designed to meet your process needs of insulation, temperature and power.
With a temperature range of 20°C up to 500°C these industrial ovens are suitable for all applications of preheating, drying, cooking, polymerization, curing, tempering, stabilization, cooling.
|
|
DRYING OVENS
EMME GROUP designs and builds ovens for this sector using unique systems which make them completely safe, simple to use, with close monitoring of the temperature in use, higher uniformity of heat spread and energy saving ability compared to other ovens on the market.
These ovens are used for:
* Aluminium treatment
* Treating surfaces
* Thermal treatement of metal, plastics and silicone materials
* Drying
* Drying varnishes
* Drying leather
* Silk-screen
* Heating systems
Our technical office can design and produce ovens according to the client’s specific needs.
Experience, professionalism and a good post-sales assistance including technical assistance guarantee the top quality of our products which are all certified and in keeping with current laws and regulations.
|
|
Applications: cooking, degassing, burning, polymerization, pre-heating, recovery, drying, stabilization, sterilization, vulcaniztion, tests,...
2 temperatures: 200°C maxi or 300°C maxi (depending on the option).
Eight sizes: from 125 litres to 2520 liters.
Several options and accessories to adapt the oven to your needs.
|
|
MINI OVEN “JOLLY”
This dryer is designed for the fast drying of serigraphic dissolvent ink or water ink on various applications. Easy operation and maintenance and high drying efficiency are the main characteristics of this machine.
Endowed of kappa for aspiring attack, mounted on 4
Self-locking wheels.
Dimensions: tape length 150 cm, Height from earth 80 cm, Weight 87 kg.
|
|
|
|
|
|
New line of electric ovens are designed for thermal treatment such as drying, heating, thermal testing in an air-flow environment.
Forced convection makes more effective drying and quicker heating, homogeneity of temperature. Good technical parameters ensure to high-quality results. This line allows choices of oven chamber from mild steel LFP or stainless steel (LFN). Available is 5 sizes at temperature ranges up to 300 ºC.
• Micro processor temperature controller with autotuning function
• Double over heat protection system
• Digital setting of temperature
• SSR relay
• High quality thermoinsulation material
• Chamber made of mild steel or stainless steel
• 3 shelves
• Horizontal air flow
• Air outlet control by valves operated manually
• Regulation of fan speed (0-100%)
• Acoustical signalization
• Short heating time
• Heating is from four sides
• Hermetic closing door
• Low power consumption
• High precision level
• Interface RS 232 and software for E5CK 2008
• Interface RS 485 and software for TCViews
• Limited warranty up to two years and later service
|
|
Type YOU 60/60
With a good capacity of filling, it occupies little place and has a performance higher than the classical devices of laboratory.
They are the great advantages of YOU 60/60.
Short durations of heating, briefs drying cycles via a guidance of optimal air and a renewal of important air as well as a remarkable homogeneity of the temperature in all useful volume, represent only some of the characteristics of this apparatus.
Useful volume: 216 liters
Range of temperature: 200°C
Guidance of the air: vertical or horizontal (TUH)
|
|
Laboratory-vacuum drying cabinet with safety hood and glove box connection for Laboratory-vacuum drying cabinetgentle drying of active substances:
* CIP-compatible
* Gap-free interior construction
* Halarized product trays
* Drip-free thermal oil supply
* Conductive transport rollers suitable for pharmaceutical applications
* Completely bonded insulation and welded chassis
* Doors can be hinged on left or right sides
* Special pivot arm for opening door in glove box mode
* Inflating seal on safety hood and glove box
|
|
Manually operated furnaces, where the product is layered on trays.
The product is then loaded by the operator via a single door or double doors. After filling the furnace and closing the doors, the operator can set the variable temperature controller and start the furnace.
Typically used in low baking of painted surfaces of small batch sizes away from the main production line.
Working temperatures depend on customer’s requests.
|
|
drying oven
Standard configuration with internal chamber, supporting frame and external cabinet made of S. S. AISI 304 (upon request, the internal chamber can be made of S. S. AISI 316).
Drying temperature up to 100°C, with tolerance lower than +/- 3°C on the fixed set-point.
Heating by means of electric heaters or steam battery
Group of electric heaters with variable current intensity for easy internal temperature control
Filters on the external air intake for wet air ejection with filtration degree ASHRAE 85% DOP.
Sturdy loading footplate with stainless steel tilting chute for introduction of trolleys
Stainless steel trolleys and trays for product loading
Scotch-brite finishing.
|
|
|
|
|
|
Electronic Drying Chamber
OPTIMUM DESIGN
Utilizing a performance enhanced, low-temperature, high volume, updraft re-circulating hot air design, the Omegasonics Optimum 6500 is the ideal machine for drying all types of electronic components after wet cleaning. Whether drying small electrical and electronic content after restoring in our line of Ultrasonic Restoration Pro System Units or our E Series line of Electronic Cleaning Stations, the Optimum 6500 is the perfect fit.
With three (3) adjustable shelves, handling large items or a variety of small electronic components is a snap. There is no prolonged waiting time either for the internal air to get up to the desired temperature. With the 6500, optimum air temperature of 120°F is achieved in less than 60 minutes from a 70°F ambient.
Unique Features:
Updraft Re-circulating Hot Air Design
3450 Watts finned heating element
Heat circuit over-temperature protection
Dual blower design 990 cfm
User friendly illuminated control panel
Digital temperature controller fully adjustable
Digital timer controlled process time
Electrical: 1 phase, 240 volts, 20 amp
|
|
Universal drying ovens LHT with stainless stell housing. Options: Tmax: 300°C, air circulation, glass door available (Tmax. only 220°C), program controller.
Vacuum Ovens LHT Vac. Tmax. 200°C. Vacuum min. 2mbar, partial pressure control 10-1100 mbar. Separately heated trays with temperature control. Electronic temperature and pressure control with display. Option: different pumps, underframe with vaccum pump, additiional trays
|
|
|
|
Dryers, Drying equipment
