|
|
. Industry : To warm surfaces and volumes (freezing industry, electronics, automotive, telecommunications, pharmaceutics...).
. Household appliances : Flexible heating elements for domestic equipments (refrigerators, freezers, small domestic appliances).
. Oenology : Must-warmer.
|
|
BS heating cord
Designed to be used in condensate draining pipes, in negative cold rooms.
Available in 40W/m power, BS heating cords have a sole cold lead at one end.
Advantages :
Very flexible, can heat continuously.
|
|
|
Parallel heating cable constant power, is the best solution for all these situations where special electric heating system is needed: electric floor heating, electric radiant floor for ramps, electric trace heating for pipes, electric trace heating for storage tanks, snow melting systems for ramps, access, roads, systems, snow melting systems for roofs, terraces, gutters, pipes, etc., electric heating for animals: pigs, pets, exotic animals habitats, electric heating for agriculture: small greenhouses, terraces, seedbeds, etc.
|
|
Technical details
- Protection class I (ground wire) - protection type IP 54
- Temperature setting:
ON 38 °C - OFF 54 °C (operating temperature of heating
system itself)*
-> Other settings upon request
- Connection:
Connecting leads (AL) 0.25 m, 3 x 0.75 mm², silicon
-> Other lengths upon request
- Mounting position: horizontal
- Fastening:
Screw fastening
|
|
|
Heaters of fluids in circulation They consist of an immersion heater adapted to the fluid in circulation and of a cylindrical body. A range of heaters monoblocs, particularly compact, was developed for the changing of heat pump. All our standard immersion heaters can be assembled in a heater. Electrowatt designs also heaters on schedule of conditions customers until several hundred kw including, if necessary, the temperature control and the power control.
|
|
These appliances are used to heat circulating fluids such as water, fuel oil, as well as air or gases in general at up to 15 bar max.
They are fitted with screw plug immersion heater, flange immersion heater or high flux rods.
Temperature sensors and controlers can control the temperarure of the flow and safety devices protect against over temperature.
Fluid circulation heaters can be connected hydraulically in series, which allows a very large heating power to be achieved.
|
|
|
Clean Water Heaters are ideal for heating municipal water for industrial washing and rinsing processes. Sturdy 0.475" diameter copper sheath elements provide superior strength and rigidity. Chromalox elements utilize high quality resistance wire for coil construction. All stock and assembly stock heaters come with mechanical AR thermostats. These thermostats are suitable for most applications. Explosion-resistant and liquid-tight thermostats are provided on E2/E3 and E4 units, respectively. Other applications include indirect heating of viscous liquids and temperature maintenance of storage tanks.
|
|
ompact immersion tube
integrated in tanks
THERMAL FLUID PREHEATER
The loop heater enables the temperature of the loop of a fluid to be maintained, the temperatures of which may vary up to 250 °C depending on the thermal fluid used. The use of the compact immersion tube in this application enables a very high degree of efficiency.
MAIN BENEFITS :
Energy savings
Avoids using a steam boiler
Design temperature up to 250 °C, depending on the thermal fluid (heat-transfer fluid) used.
The very low volume of fluid enables the temperature to be reached very quickly.
Energy decentralisation
Low overall dimensions
Ease of use
Autonomous equipment
USE:
Food industries:
Replaces steam
Heating of various tanks and tunnels (pasteurisation, frying and scalding)
Production of sanitary hot water
Market gardening industries:
Heating various baths
Metallurgical industries:
Vacuum evaporator / concentration of solutions
Heating of various baths
Industrie chimique :
Cosmetic decoction baths.
|
|
At ECAS, we are expert manufacturers of crankcase heaters.
The BCC it's an electricserial resistance protected with a metal braid, fixed to a flexible strap with an adjustable traction device which allows the crankcase heaters to be adapted easily to the object to be warmed.
Specially designed for the controlling and maintaining the temperature of compressors, boilers, storage tanks, etc.
Insulation resistance: 100 mega ohms min. at 2,500 V
Connection outlet: hose 3 x 0.75mm² - 1m
Tolerance W: ±10%
|
|
U.L. Recognized - Guide SEOT2, file SA4093 for use in air conditioning equipment.
C.S.A. Certified - Guide 165-E-90, file 016386-0-000 for use in air conditioning equipment.
Applications:
Crankcase heaters are used to overcome the problem of migration and condensation of refrigerant in the crankcases of compressors used in air conditioning and heat pump systems.
They are designed to keep the crankcase oil at a temperature higher than the coldest part of the system to prevent migration.
Features:
Hotwatt Crankcase Heaters are constructed of the highest quality corrosion
resistance materials and sealed against moisture.
The following list Hotwatt Crankcase Heaters by the OEM manufacturer. In addition, custom designed crankcase heaters and variations to the units shown are also available.
|
|
In ECAS we manufacture heating blankets and heating bands, for the control and maintenance of the temperature of drums and containers.
Models BFVFV and BFVIBC: Consists on an electric flexible resistance placed in a blanket or band, manufactured with fabric of glass fiber.
All our heating blankets and bands, controls and regulates the temperature with a thermostat recommended due the requirements of each project.
We manufacture blankets and bands for drums from 25 to 200 litres, and containers IBC of 1000 litres, but we also fabricate custom blankets.
Drums: of 200,100, 50 and 25 Litres
IBC container: 1.000 Litres
Power (W):
Drums 200 L: 750 W, 1.000 W, 1.500 W
Drums 100 L: 750 W
Drums 50 L: 300 W
Drums 25 L: 200 W
IBC Container of 1.000 L: 2.000 W
Range temperature: 0 - 80 ºC
Types of fasteners: Velcro. Plastic buckles or clasps, Grommets
Application
Heating of drums, storage tanks, Instrumental of laboratory, etc.
|
|
|
Heating sleeves to heat segments of 200 litre barrels per DIN. both the inner and the outer sheath of the barrel heating sleeve are made of aluminium sheet, which ensures maximum protection of the electrical components against mechanical damage. A hinge with campling closure that divides the heating surface into two semi shells permits convenient assembly, without the heating element needing to be bent. The barrel can be heated complete by using 3 sleeves.
|
|
Holroyd Silicone Side Drum Heaters (HSSD Belts)
• Silicone Rubber insulated
• Double insulated construction
• High temperature tolerance
• Simple spring catch Assembly
• 20c to 120c Thermostat
• 2 Metre Power cable
• Standard Sizes 25L, 50L, 105L, 200L
• Bespoke Sizes to order
• Ex-Stock
Holroyd Insulated Side Drum Heaters (HISD Jackets)
• Teflon coated polyester Jacket
• Water resistant
• Glass Filament Blanket Insulation
• Adjustable Quick release Buckles
• -5c to +40c or 0c to 90c Thermostat
• 3 Metre Power Cable
• Standard sizes 25L, 50L, 105L and 200L
• Bespoke Sizes to Order
• Double Insulation IP40
• Ex-Stock
Holroyd Base Drum Heaters (HBD)
• Robust steel construction
• Even heat over platen area
• 0-150c Thermostat
• 110 or 230 Volt Options
• 2 Metre armoured power cable
• Ex-Stock
|
|
Insulated Flexible Heating jackets for containers and drums from 20 litres up to 1200 litres in size.
High grade insulation combined with a range of custom coated fabrics allow us to offer a performance specification from "winter warming" anti-freeze applications through to melting of solids from 200 litre drums.
Power ratings are suitable for both plastic and steel containers.
The jackets are easily fitted and removed using click-in buckles and straps, and can be handled safely even after use due to the outer insulation layers.
Standard adjustable dial thermostat ranges are upto 40 degrees C or upto 90 degrees C, with options upto 160 C and digital display of temperature.
Custom sizes can also be manufactured upon request.
Standard designs available for IBC's (Intermediate Bulk Containers) from most major manufacturers.
|
|
|
|
|
|
The THERMOSAFE Induction Drum Heater has been proven world wide over more than 20 years as the fastest, most reliable and safest method of melting solids from steel drums, and for the speedy heating of viscous liquids.
It is certified to the ATEX and IECEx standards for use in potentially explosive atmospheres, and is IP66 rated, so can be used in wet areas (even hosed down whilst operational!) and other harsh environments.
The external surfaces are high grade glass reinforced resins able to resist chemicals and acids, so the heater can withstand accidental splashes of hot liquids. There are no moving parts and it is completely maintenance free, so its lifetime operating costs are incredibly low.
No contact with the steel drum is required, as heat is generated by the drum wall itself, so it is exceptionally energy efficient, saving over 50% compared to conventional radiant heaters, and even more compared to steam ovens.
These units can be used individually, for example in research labs or small batch blending plants, or in groups at point of use, as highly cost effective replacements for large drum ovens.
|
|
3a drum heater is a flexible panel with two coated fabrics : an heating side and an insulated side.
3a drum-heater is supplied with eyelets which, laced with an elastic rubber, lets the barrel heater lie flat on the barrel, essential condition for a good heat exchange.
In comparison with heating belts which need several main supplies and do not wrap totally the barrel, 3a barrel heater totally wraps the cylindric part of the barrel, allows smooth and homogeneous warming and, thanks to the insulated face, is maintaining temperature in the barrel for hours after you switched it off.
A utility is accessible to determine the time of heating necessary for the application.
|
|
Mica Drum Heater (GDH)
Heats low-melting-point solids in standard metal 55 gallon drums. Constructed of corrosion resistant nickel plated steel throughout. Features pilot light, infinite control switch, and 6 foot heavy duty rubber insulated cable.
|
|
DRUM HEATERS - for 200 litre barrels.
Drum Heaters facilitate the handling of solidified or viscous materials like adhesives, waxes, tar, chemicals, oils etc. They eliminate cumbersome methods and high investments, associated with steam and oil or fire wood heating.
Construction
Drum Heaters consist of a cylindrical metal cover carrying the flexible heating elements. A 2" thick thermal lagging of glass wool provides insulation and the metal casing makes for a rugged unit that can be wrapped snugly around the drum. The Drum Heater is hinged, and is mounted on castors for convenience. A base heater, also encapsulated in metal provides bottom heating. Control Panel incorporating thermostatic control is provided with the heaters.
|
|
In ECAS we manufacture heating blankets and heating bands, for the control and maintenance of the temperature of drums and containers.
Models BFVFV and BFVIBC: Consists on an electric flexible resistance placed in a blanket or band, manufactured with fabric of glass fiber.
All our heating blankets and bands, controls and regulates the temperature with a thermostat recommended due the requirements of each project.
We manufacture blankets and bands for drums from 25 to 200 litres, and containers IBC of 1000 litres, but we also fabricate custom blankets.
Drums: of 200,100, 50 and 25 Litres
IBC container: 1.000 Litres
Power (W):
Drums 200 L: 750 W, 1.000 W, 1.500 W
Drums 100 L: 750 W
Drums 50 L: 300 W
Drums 25 L: 200 W
IBC Container of 1.000 L: 2.000 W
Range temperature: 0 - 80 ºC
Types of fasteners: Velcro. Plastic buckles or clasps, Grommets
Application
Heating of drums, storage tanks, Instrumental of laboratory, etc.
|
|
Standard heating covers 1m², 2m² and 4m²
Flexible heating pannel with one heating face (red face) and one insulated face (blue face) ; standard square output is 400W/m².
Standard flexible heating pannels are equipped with eyelets to be laid easily.
Available in 3 different sizes: 1m², 2m² et 4m².
Precise temperature when regulating with a thermostat
Easy to store
Quick laying
|
|
Heaters for the thermo-regulation of enclosures, for application on DIN rail, and available in three version:
- with bipolar (15-30W) or three-pole (45-150W) power cable
- with three-pole terminal block (45-150W)
- ventilated (250-400W)
|
|
|
Condensation poses a particular risk for control electronics, especially with outdoor siting, but also indoors. Various different output categories ensure that the correct thermal output is always available. In this way, the total required thermal output can be distributed with complete accuracy within an enclosure.
|
|
Units for DIN or screw mounting.
TH heaters, installed separately from cooling unit, must be connected to a TMC thermostat. When used to prevent cabinet condensate they should be electrically connected also when cabinet is off.In this cabinet it’s better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Technical details
- Protection class I (ground wire) - protection type IP 54 (DK = IP 20)
- Temperature setting:
ON 25 °C - OFF 55 °C (operating temperature of heating
system itself)*
Tropical version possible: ON 35 °C - OFF 65 °C
-> Other settings upon request
- 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 3 x 0.75 mm² PVC
- > Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm²
- Mounting position: vertical
- 2 fastening alternatives (optional)
Snap fitting for 35 mm DIN rail (figure 1)*
Screw fastening (figure 2)
|
|
PTC units for DIN bar application.
EH/FH heaters, installed separately from cooling unit, must be connected to TMC thermostat. When used to prevent cabinet condensate they should be eletrically connected also when cabinet is off.In this cabinet it’s better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
The Faratherm Induction Base Heater consists of an induction coil, encapsulated in glass reinforced resin with a heating plate located on top. It uses the same technology as our proven THERMOSAFE Induction Drum Heater.
Powered by single phase ac electricity, it is certified for use in potentially explosive atmospheres to the ATEX and IECEx standards for Zones 1 and 2.
With an ingress protection rating of IP66 and no moving parts, it is suitable for use in harsh environments. There are no heating elements, and no electrical contacts to spark or arc as the maximum temperature is self limiting.
The Faratherm unit can be used by itself, or in conjunction with our THERMOSAFE drum heater for fastest possible melting of solids from drums, and for rapid heating of viscous liquids.
|
|
Technical details
• Explosion proof according to EN: 50018
• Heating element: high-performance heater cartridge
• Radiator: aluminum profile, black anodized
• Connection: Si HF-JZ 3 x 1.5 mm², 1 m long
• Connection PE: 4 mm²
• Fastening: clip for 35 mm top hat rail, EN 50022
• Mounting position: vertical
• Operating / storage temperatures: -20 to + 40°C / -45 to + 70°C
• Protection type: IP 65
• Protection class: I (protective conductor)
|
|
INTERTEC offers the widest selection of explosion-proof heaters worldwide.
- ATEX/CENELEC approvals for Europe
- CSA/NRTL approvals for America
- GOST approvals for the Russian Federation
Our EX-heaters in combination with EX-controllers satisfy all requirements from freeze protection as well as high demands in the analyse technic.
For further questions please contact: Tel.+49-9445/9532-0
|
|
THERM HI "smart heater" is a system consisting of
an explosion-proof electric heater and a
microprocessor, designed to control the air
temperature in instrument enclosures and protective
cabinets and to limit the surface temperature of the
heater.
The "option E" is equipped with an intrinsically safe
sensor, thus allowing measurement and accurate
regulation of the temperature of the instruments and
equipment (e.g. of manifolds).
... THERM HI heaters are designed to solve
sophisticated and complex heating problems in
hazardous areas, and in particular for high
temperature maintenance of analyzing equipment.
|
|
Rectangular fin elements
Consisting of a "U" shaped element on which are crimped the rectangular fins (25 x 50 or 40 x 80) made of protected steel or stainless steel and usually equipped with threaded glands.
|
|
|
|
Heating resistors
