|
|
Biofil PES
Incorporating a hydrophilic membrane, the Biofil cartridge has a unique mirrored asymmetric structure which gives the media added strength and very low clean pressure drops. This helps to ensure that cartridge integrity is maintained when repeatedly steam sterilised. The characteristics of the membrane also results in excellent resistance to hydrolysis, along with low protein binding and colour stripping. Furthermore Biofil PES cartridges have excellent chemical compatibility across the full range of pH values.
Biofil PES cartridges have been validated and are ideal for applications ranging from the production of beverages to the filtration of blood and serum. They compare favourably in many applications with alternative cartridges manufactured using Nylon, Cellulose and PVDF.
|
|
TARGA® industrial water cartridges provide compact pretreatment for ultrapure water systems.
8-inch TARGA® cartridge
TARGA® industrial water ultrafiltration cartridges are produced for general water treatment applications. They are particularly effective for pretreatment to reverse osmosis membranes.
• pH Tolerant
• Chlorine Resistant up to 200 PPM at 10.5 pH
• Temperature range of 32 degrees - 104 degrees F
8-inch diameter cartridges are available in two lengths: 48-inches and 72-inches.
TARGA® cartridges have a broad range of applications, including:
• Carbonated Soft Drinks and Bottled Water
• Boiler Make-up Water
• Microelectronics
• Pharmaceuticals
|
|
Filter slats
* high tensile strength
* different specifications
* length as per your requirement
|
|
General description:
Media Filter - a multi density media filter using time proven aggregate and sand with a final Anthracite layer. This filter is available in three sizes and includes an automatic backwash controller. The tanks are high quality aluminum lined with an epoxy impregnated fiber wound exterior.
|
|
|
A revolutionary, highly efficient ceramic filter media for the removal of oxidized iron and suspended matter. Tremendous loading capacity, extremely fast cleanup time and an attrition rate of nearly zero
|
|
PiP housings and PiP elements are used for process filtration. It is about a brand-new developed series of filters. It includes pleated cartridge filter elements and bag replacement elements for process filtration as for instance filtration of cleaning liquid, lacquers, colors. Originally, pleated cartridge filter elements were developed for the filtration of cleaning liquids, nevertheless they are applicable in a wide range of areas.
|
|
|
Designed for removing trace contaminants down to 1 micron. Ideally suited for filtering and corrosive solutions including electroless copper and nickel to 200°F (93°C).
|
|
|
A FLOWLINE stainless steel bag filter housing from Eaton is the best choice for industrial, commercial and OEM applications that do not require a Code Stamp. Its cost-effective design incorporates all of the features heavy duty applications demand, including an investment cast swing bolt cover that can be adapted to different opening directions in the field and a quality stainless steel mesh restrainer basket for reduced pressure drop.FLOWLINE's stainless steel construction ensures years of trouble-free, consistent performance at a price comparable to that of many carbon steel housings.
|
|
CIH multi cartridge V-band clamp closure housings are a proven design suited for commercial and industrial applications. Offered in 4,5,7,12,and 21 round configurations and in 304 SS or 316L SS. All CIH housings are designed with Universal cartridge cups, allowing you to use DOE style cartridges or 222 SOE cartridges with fin or flat end. This gives you one housing that can meet your nominal and absolute filter needs and provides quick cartridge change outs. Housing is standard with EP gasket and also offered in other materials and port sizes, allowing the CIH to meet a wide spectrum of applications. Every housing is supplied with a mounting kit and operations manual.
|
|
The Hilco TurboFlo Duplex Filter line is easy to operate and maintain with a low turning torque and no jacking of the sealing pads. Welded-in transfer valves and high flow synthetic elements save space, and flow is under the filter cartridge which does not impinge on the filter elements. With no flanges between the transfer valve and filter housing, there are fewer potential leak points.
Features includes:
• ASME Code construction
• O-ring sealed covers
• Coreless elements
• Standard carbon steel and 316 stainless steel
The TurboFlo Duplex Filter is also available in 1-1/2” to 8” inlet and outlet connections for flows up to 2000 gpm and pressures up to 5000 psi.
For complete product information, request bulletins TBF-2 and TEB-2.
Other Filter Housing products include:
• Integral Duplex Filters
• Standard Housings for High Flow Synthetic Elements
• Standard Non-Code Housings
• Bag Filter Housings
• Seal Gas Duplex Filter Housings
|
|
|
AAF AmerKleen filter cartridges are protected at all times by an all metal, filter housing. The AmerKleen housing is equipped with an anti-surge assembly consisting of a wire form attached to the back of each sealing frame. By holding the cartridge firmly in place, the housing protects it against turbo-surge. The AmerKleen cartridge is designed to be changed at the normal 90-day maintenance cycle, with an adequate safety margin should the locomotive encounter delays in servicing. When the time comes, installation is a fast and easy process. By the simple removal of two bolts and a sealing frame, the AmerKleen cartridge is front-loaded. Replacing the sealing frame automatically forms an air-tight seal. Normal air flow through the filter insures that all seals remain tight without the need for time-consuming alignment.
|
|
These cartridge-filter housings are rugged and low in cost. They hold five cartridges, in 10-inch, 20-inch, 30-inch, or 40-inch lengths, using industry standard designs (222, SOE, or DOE). The unique, “quick-opening” clamp design uses a standard gasket.
Standard Features
- Low pressure drop
- Permanently piped housings are opened without disturbing the piping or requiring tools
- Quick-opening, clamp-type cover
- Carbon or stainless steel housings
- Adjustable-height tripod legs
- Holds 5 cartridge elements
- Accommodates cartridge elements in four lengths: 10”, 20”, 30”, 40”
- 125-psi rated housing
- 3/4-inch clean-dirty/gage ports
- 2-inch female NPT ports
- V posts or threaded-center posts
- Standard hardware V-post and spring seals are 316 stainless steel.
- O-ring seals: Buna N, EPR, Viton®
|
|
The SONDERMANN filter housings are specially designed for the removal of organic and inorganic impurities from aggressive and neutral liquids by means of deep- bed and surface filtration.
Advantages
- Vast range of varieties
- Solid plastic version
- Easy operating thanks to the quick fastening
- Combination possible with the complete range of products
Applications
- Electroplating
- Caustic and purifying plants
- Waste and fresh water treatment
- Photographic industries
- Textile and foodstuff industries etc.
|
|
FM4X1-1: 4-round 10 in. Cartridges, 1 in. NPT; 25 gpm max; (Legs Optional)
Description:
100% stainless steel design, V-band clamp lid closure, pressure rating 150psi. Available in 304 or 316ss.
|
|
|
|
|
|
Industrial Housings
1B1/2
* Available in either cast-iron and steel, or 304 stainless steel construction.
* Centerpost design for easy cartridge changeout.
* Choice of one- or two-high cartridge models.
* Three-piece construction for easy cleaning.
P SERIES
* PE and PT Models are cast iron and steel housings designed for industrial oils or non-aqueous applications.
* Available separately or mounted as mobile units, ideal for transformer oil filtration.
* PTS Model is a 304 stainless steel housing designed for aqueous or corrosive applications. Single V-band clamp closure.
1H1 MODEL
* Ideal for high-pressure applications (1000 psi @ 250°F).
* Dual purpose/use for liquids or compressed air and gas.
* Durable steel construction.
* Housing design prevents cartridge erosion.
* Uses single cartridge of a variety of cartridge types.
CT SERIES
* Choice of either forged brass and 304 stainless steel or all 316 stainless steel construction for versatile applications.
* Drilled and tapped mounting pads, ready for mounting bracket installation.
* Choice of one-high or two-high models.
* Available in 300 psi design.
|
|
Features
Available in Type 304 Stainless Steel, Type 316 stainless steel or carbon steel with standard Buna N o-rings, Viton® o-rings are an available as an option.
A counter balanced spring assisted cover lifting mechanism balances the cover perfectly giving it a "weightless" feel. Opening and closing the cover is "finger tip" easy.
QIC-LOCK rapid opening and closing mechanism ensures simple, operator friendly operation with minimal downtime for bag change-outs. Reduces downtime to increase productivity and decrease operating costs.
Unique 3-point hold down for bayonet fitting ensure high quality of the seal between each filter bag and the housing body. A supplied special tool ensures, simple effective operation.
Side inlet and bottom outlet provides easy and complete drainage. A standard tangential outlet reduces housing height.
Available in three sizes for 4, 6 or 8 standard size 02 double length filter bags.
|
|
|
|
|
|
CCL Series Housings
Pall CCL Series Housings accept Pall 1000 style filter elements in a 10, 20 or 30 inch length, or Pall 21/2%u2033 diameter UNI CAP style pleated filter elements. This series of housings is typically used for flow rates of 15, 20 and 25 GPM for the 10, 20 and 30 inch cartridges respectively. The housings are constructed of a 316 stainless steel investment casting head and a 316L stainless steel bowl. One or two polypropylene couplers, to join 10%u2033 1000 style filters together, are included for 20 and 30 inch housings, respectively. Inlet/outlet connections are 1%u2033 NPT or 1%u2033 flange. The head and bowl of the housing are fastened with a quick opening stainless steel Tee handle V-band clamp. Head to bowl sealing is by standard 242 O-ring.
Specifications
Design Ratings:
Pressure: 200 PSIG (1379 KPA)
Temperature: Limitations due to O-ring material.
Buna N: -20°F to 250°F (-29°C to 121°C)
Viton A*: -20°F to 400°F (-29°C to 204°C)
Ethylene Propylene: -20°F to 300°F
(-29°C to 148°C)
A bowl drain connection, as well as 2 pressure taps in the head are standard on all models.
The housings may be mounted in any position except for oil mist removal from compressed gases, where it must be mounted vertically with the bowl down.
|
|
|
CSH sanitary cartridge housings, available in 1,3,6,8,12 and 21 round models with swing bolt and clamp closures are a proven design suited for high purity beverage, chemical and pharmaceutical applications. They are manufactured in 316/316L Stainless Steel with a 25 RA internal finish. All CSH housings are standard with 2-226 style cartridge adaptors with removable tube sheet, giving you a positive locking tab seal. This allows flexibility in one housing to use different cartridge lengths and maximize filter performance and cost. CSH housings have no internal threaded parts that come in contact with the process fluid and are standard with food grade silicone gaskets. 1” sanitary gauge port tops with 1/2” sanitary vent and drain ferrules are standard features.
|
|
High efficiency terminal filters for highest requirements for air purity and hygiene.
High efficiency terminal filters are used as final filters in areas with the highest requirements for air purity and hygiene such as in the medical, biological and pharmaceutical industries as well as in other sensitive areas.
Both HEPA and ULPA filters can be used.
These filters can be combined with different ceiling diffusers from the TROX standard product range.
- Particulate air filter ceiling diffuser
- Main filter for high air purits and sterility
- Ceiling diffusers are a comfortable way to generate mixed air flow quietly,
even for large quantities of air.
|
|
Sanitary grade housings
Designed for the demands of critical applications particularly in the pharmaceutical, microelectronics and food and beverage industries, our sanitary grade housings have easy to use closures with a crevice free construction. The internal surfaces are resistant to bacterial accumulation and are easily steam sterilised or chemically sanitised. Microbial security can only be guaranteed with this grade of housing.
|
|
CHR single cartridge ring closure housings are a proven design suited for commercial and industrial applications. Available in 304 SS, 316 SS or Brass head with 304 SS sump. The CHR housings are rated for 300 psi and are designed for DOE style cartridges with machined knife edge seal surfaces for a no-bypass seal. All sump seals are spring loaded allowing you a variety of cartridge lengths and providing quick cartridge change outs. With the complete range of O-ring materials and port sizes the CHR will meet a wide spectrum of applications. Every housing is supplied with a mounting kit and sump rod.
|
|
|
|
|
|
Oil Level Dipsticks , C4.0410/C4.0412/C4.0421/C4.0431/C4.0450/C4.0464
Application
Controlling the oil level in hydraulic oil or lubricant reservoirs
Construction and function
ARGO-HYTOS oil level dipsticks are robust semicircular metal rods with an O-ring seal.
A mounting bolt with a suitable hole is supplied with each dipstick. Dipsticks are available in various lengths, with various markings, and with various mounting bolts (see selection chart).
Special features
- The robust material withstands even the most severe operating conditions
- The integral O-ring provides a 100% tight seal
- A suitable dipstick mounting bolt can also replace one of the mounting bolts of an in-tank return or suction filter
Mounting
The bolt supplied with the oil level dipstick is installed either in a separate threaded hole or in an already existing mounting hole for an in-tank filter. This eliminates the need of an extra mounting hole. If used as a filter mounting bolt, care should be taken to provide a proper seal between the tank, the filter and the mounting bolt.
|
|
Filter elements can only be used with optimal economy if their ability to retain contamination is fully utilized without risk. Mechanical and electronic sensors integrated in the filters or retrofitted react to continuous changes in pressure resulting from changes in the degree of contamination. These changes are then indicated via pressure gage or visual and optoelectrical switch, depending on the version used. On suction filters the negative pressure is registered, on pressure filters differential pressure, and on return-line filters banking-up pressure. This enables the operator to determine the optimal time to change the filter elements without entailing any risk.
|
|
|
Koch-Glitsch Mass Transfer Technology is unsurpassed in its offering of high performance distillation trays for the refining, chemical and hydrocarbon processing industries. SUPERFRAC® trays have unique features and performance benefits for increased capacity in virtually any service. These technologically advanced trays employ innovative downcomer designs and active area enhancements to provide minimal pressure drop, optimum mass transfer efficiency, and high capacity. Let Koch-Glitsch help you select the best solution to meet your processing requirements.
|
|
|
ACS Industries, Inc. has supplied After-Treatment Exhaust System Mounting Components to automotive OEMs and Tier I Suppliers since our first knitted wire mesh support systems came to market in 1975. Since then, our exhaust component products have established themselves in both on- and off-highway applications throughout the world. As global emissions requirements tighten and more after-treatment systems using catalyzed substrates are used, ACS' After-Treatment Exhaust System Mounting Components will continue to play a key roll.
|
|
|
|
|
|
‘Becoil’ knitted mesh demisters.
In many industrial processes it is necessary to remove mist or spray droplets from air or gas streams in order to purify the gas, remove liquid which would contaminate the subsequent process, damage downstream equipment, constitute an undesirable atmospheric emission, or to recover a useful liquid product of the process.
'Becoil' Demisting Units are separators of the impingement type consisting of multiple layers of fabric knitted from metal or plastic monofilaments, crimped and than assembled so that the crimps cross in successive layers. Pads fabricated in this way have a very uniform voidage with an extremely high ratio of filament surface area per unit volume of pad.
Collected liquid in the mesh forms discrete droplets on the filaments which fall off as the force of gravity overcomes the combined forces of the rising gas and surface tension, which tend to hold the droplets to the filament.
'Becoil' Demisting Units have been specially designed to achieve highly efficiency removal - up to 100% on entrained droplets above 5 microns in size, while generating low pressure losses and are virtually maintenance free.
|
|
|
|
|
|
The filter elements, including sintered metal powder filters, sintered metal fiber filters, titanium filters and other alloyed filters, are manufactured by isostatic pressing or co-axial pressing via powder metallurgy process. Available materials are: stainless steel 316L, 304L, 904, Titanium, Inconel, Hastelloy, Nickel, Monel and other alloys .etc.on request.
The pore size can be adjusted by suitable selection of the powder size fraction and the process parameters. It has the type of tube, disc and stack of lamination and so on.
Main Applications
1. Gas and liquid filtration
2.Solid catalyst recovery
3.Filtration of slurry oil and other petrochemical products
4.High-temperature gas filtration
5.Fluidization
6.Powder conveying
7.Aeration, and other applications in various industrial fields.
Main advantages
1. Good shape stability
2. High mechanical strengthen and good integrity
3. Controllable pore sizes and porosity
4. Good permeability
5. Good corrosion and thermal resistance
6. Easy to be made into complicated shapes, can be put together by soldering or gluing
7. The service life can be prolonged by cleaning and regenerating process
|
|
Stainless Steel Filter Elements:
Stainless steel filter elements are made up of several layers of 316 mesh that are sintered together to form an integrated porous element. The middle mesh is of very fine gauge and determines the filtration efficiency of the elements. This layer is then overlaid with inner and outer layers of coarser mesh, to give support and protection.The elements are a typical surface filter and the contaminants are retained on the surface of the filtration layer, this makes cleaning and back flushing a simple process. These filter elements should be ultrasonically cleaned to give best results. Stainless steel filter elements are particularly useful in heavily contaminated applications and for use as pre-filters before disposable
type final filters. Gaskets are required with stainless steel filter elements. The options are Viton, PTFE or high temperature annealed copper.
|
|
Suitable for the filtration of fine dust type in gas turbines, compressors, shot blast, tobacco, pulverized coal ash, floating, pigment, wood dust collection.
- Imported cellulose fiber or synthetic fiber for base media
- Excellent filter efficiency
- Wide pleat spacing, great filter surface
- Electrochemical or stainless steel plate top and bottom, no rust
- Perforated zinc galvanized metal inner core, allows good airflow
- Specialty chlorine rubber gasket to ensure airtight sealing
- Applicable temperature: 65°C—135°C
|
|
# various geometrics
# with wire mesh and metal fibre felt
# for high and low pressure
# offered as
* coated filters
* pleated filters
* screen baskets
* filter candles
* custom-made products
|
|
|
|
Filter elements for liquids: cartridges, housings..
