|
|
|
Filtermist collectors are low-cost, highly efficient units. These easy-to-install accessories operate under the principle of centrifugal impaction. A rotating drum draws air and mist droplets into the collector. The mist particles are coalesced into liquid which is drained back to the coolant tank. Clean, oil-free air is returned to the shop.
|
|
|
The Electric H2O Centrifugal Separator uses centrifugal force to separate suspended particles from the water. Concentrated particles are forced along the separator wall, traveling downward to the collection chamber, while the clean fluid is forced to change direction by the redirection plate. The vortex breaker allows the particles to settle in the collection chamber. Particles concentrated in the collection chamber are periodically purged or continuously bled from the separator as required by each application. Our Separator will remove 98% of particles greater than 40 microns and with a specific gravity of 1.8 or greater.
|
|
Disk stack centrifuges with self cleaning bowl are used for clarifying and 3-phase separation of liquid-solid suspensions. Clarifying means to separate suspended solids from liquids (2 phases). 3-phase separation means to separate two inmiscible liquids including separating solids simultaneously.
FLOTTWEG's new developments are the disk stack centrifuges of the AC series. They are equipped with the SoftShot discharge system and feature especially exact partial discharge and smooth run.
FLOTTWEG's product range for disk stack centrifuges comprises several sizes and covers throughput capacities from below 1 m³/h up
to 85 m³/h.
Typical applications:
Beverage industry, food industry, chemistry/pharmacy, animal/vegetal fats and oils, mineral oil, etc.
|
|
|
Centrifuges provide excellent separation of very fine contaminants from water and low viscosity oil based coolants. Flow rates to 20 GPM. Helps minimize media consumption in cartridge or stacked disc filter systems for low micron or sub micron filtration applications.
|
|
ZM basket centrifuge
This model is an easy-to-handle, robust construction with manual removal and discharge of the sludge basket. In one cycle, up to 14 litres of sludge (19 kg) can be separated.
ZA automatic peeling centrifuge
The PLC controlled ZA cleans up to 2000 litres of mass finishing process water per hour. The sludge separated in the rotating drum is fully automatic scraped into a sludge container.
|
|
|
|
|
|
ADF Series defoaming equipment , adopt the centrifugal power to break the foam during the fermentative process ,separate the liquid and the gas, the foam-liquid separated can be back to the fermented tank, reduce the lose of escaped-liquid. It can be more efficiently reduce the lost of fermented-liquid under the condition of big ventilation when combined with the exhaust condenser system.
The foam comes into the rotor , and be broken by high Shear power ,the liquid released from the foam falls to the wall by centrifugal power ,and be compressed as the liquid- flow, some of the liquid flow back to the fermented tank, some flow back to eddy shell collector ,and back to the fermented tank through the pipe finally.
ADF is applicated for defoaming during various type of fermentative process .Such as , fermentative process of antibiotics , fermentative process of amino acid organic, fermentative process of Yeast raise, fermentative process of vinegar. It’s feature as following:
1.Do not use or rarely use of chemical defoamer, eliminated the harm of chemical defoamer to the fermentation and the downriver separation.
2.Improve the coefficient of liquid-loading and the stability of biochemical reactions, reduce the escaped liquid
3.Reducing the time of Microbial staying in the foam, improve the efficiency of biochemical reactions
|
|
The automatically draining centrifugal separators of the A series achieve optimum filter fineness even with a high quantity of sludge. Up to 50 kg per hour can be discharged, depending on the type of sludge. The separated sludge has lower residual moisture.
|
|
Centrifuge Cloths
These continuous filters use centrifugal force in a similar way as in a drum centrifuge. But in this case the wall of the centrifuge is a filter media that allows the filtrate to pass through while leaving the solids on the surface. These solids can be washed and then removed continuously by a unloader knife and discharged out the bottom of the device.
Menardi is able to supply centrifuge cloths to retro-fit all standard designs of centrifuge filters. All cloths are laser cut from computerized pattern designs to ensure precision and repeatability.
|
|
High Sludge Volume Separator
The Turbo T40 picks up where the T18 leaves off by doubling the solids capacity- to almost 2 gallons per cycle. The T40 includes proprietary nozzles that allow solids dewatering at high speeds.
A geared scraper drive for solids discharge ensures long term reliability. And custom engineered scraper blades means we can match scraper performance to the type of solids- whether the solids compact hard like glass, or form a sticky paste like certain paint solids.
Typical Applications
- Metal Cutting and Grinding
- Ceramic and Glass Grinding
- Paint Booth Water Curtains
- Waste Oil Clarification
- Zinc and Iron Phosphate Baths
- Vibratory and Tumbling Wastes
Features and Benefits
- High Bowl Speed for Maximum Separation Efficiency
- Uses No Consumable Media
- High Speed Dewatering Reduces Solids Disposal Volumes
|
|
Monitoring:
- protective motor switch
- "KLIXON" thermal protection in centrifuge drive
- sensor-monitored sludge cover
- heating protection for hydro-clutch
- vibration monitoring
- speed/scrape-out monitoring
|
|
The NZ-50 centrifugal separator is suitable for tasks involving low volume flows and solid quantities. Sludge is drained manually.
The compact design allows easy integration in production systems, for example on machining centres.
Thanks to special materials, use in aggressive media (90° C, pH 1-14) is also possible.
Application: Fine cleaning of coolant lubricant emulsions and oils, surface treatment baths, washing or vibratory grinding fluids, etc.
|
|
|
|
|
|
In-Line Separators for Industrial Applications
Use our centrifugal-action separator to remove grit, sand, metal chips, fines, and other solids from liquids. Perfect for use as a pre-filter to extend the life of fine filtration systems. These units require little or no maintenance, as there are no moving parts to fail or wear out, or filter media to clean or replace. The unit only requires a simple purging, eliminating downtime due to cleaning or backwashing. For flows from 6 gpm and retention ratings to 50 micron.
Features
- Low constant pressure drops
- Piped housings
- Carbon steel or stainless steel (304 or 316) construction for housings
- All housings are electropolished to resist adhesion of dirt and scale
- ASME code stamp available
- Pipe sizes 3/8 through 6-inch (larger sizes also available)
Typical Applications
- Cooling towers
- Process water
- Food processing
- Chemical processing
- Well water
- Pulp & paper mills
- Mining operations
- Steel mills
- Petrochemical industry
- Power plants
|
|
Benefits of MZF-T05 Turbo centrifuges
Intake via free gradient (gravitational) or via a pump
Dirt particles are separated out of the fluid
Dirt particles are deposited on the wall of the sludge insert.
The cleaned fluid is not pressurised as it leaves the rotor.
|
|
Decanter Hercules Series
HERCULES 2
- Installed electrical power: 45 kW
- Rotation: 3350 max giri/min
- Centrifugal power: 2950 max x g.
- Bowl diameter: mm 470
- Hydraulic capacity: l/h 35.000
HERCULES 3
- Installed electrical power: 52 kW
- Rotation: 3350 max giri/min
- Centrifugal power: 2950 max x g.
- Bowl diameter: mm 470
- Hydraulic capacity: l/h 45.000
HERCULES 4
- Installed electrical power: 52 kW
- Rotation: 3350 max giri/min
- Centrifugal power: 2950 max x g.
- Bowl diameter: mm 470
- Hydraulic capacity: l/h 55.000
|
|
Decanter 600 Series
FP 600 M
- Power 11 kW
- Max rotation 4100 rpm
- Max centrifugal force 3,300 xg
- Slenderness ratio 2,62 L/D
- Bowl diameter 353 mm
- Water flow rate 6000 l/h
- Overall length 2250 mm
- Overall width 1050 mm
- Overall height 1400 mm
FP 600 RS/M
- Power 11 kW
- Max rotation 4100 rpm
- Max centrifugal force 3,300 xg
- Slenderness ratio 3,48 L/D
- Bowl diameter 353 mm
- Water flow rate 9000 l/h
- Overall length 2550 mm
- Overall width 1050 mm
- Overall height 1400 mm
FP 600 2RS/M
- Power 15 kW
- Max rotation 4100 rpm
- Max centrifugal force 3,300 xg
- Slenderness ratio 4,32 L/D
- Bowl diameter 353 mm
- Water flow rate 12000 l/h
- Overall length 3000 mm
- Overall width 1050 mm
- Overall height 1400 mm
|
|
Giant 2
- Power 75 kW
- Max rotation 2000 rpm
- Max centrifugal force 1,570 xg
- Slenderness ratio 3.59 L/d
- Bowl diameter 700 mm
- Water flow rate 110,000 l/h
- Overall length 5,200 mm
- Overall width 2,200/3,250 (with Stab.) mm
- Overall height 2,200 mm
|
|
Jumbo 1
- Power 30 kW
- Max rotation 3,350 rpm
- Max centrifugal force 2,950 xg
- Slenderness ratio 2.51 L/d
- Bowl diameter 470 mm
- Water flow rate 25,000 l/h
- Overall length 3,000 mm
- Overall width 1,470 mm
- Overall height 1,650 mm
Jumbo 2
- Power 37 kW
- Max rotation 3,350 rpm
- Max centrifugal force 2,950 xg
- Slenderness ratio 3.38 L/d
- Bowl diameter 470 mm
- Water flow rate 35,000 l/h
- Overall length 3,500 mm
- Overall width 1,470 mm
- Overall height 1,650 mm
Jumbo 3
- Power 45 kW
- Max rotation 3,350 rpm
- Max centrifugal force 2,950 xg
- Slenderness ratio 4.25 L/d
- Bowl diameter 470 mm
- Water flow rate 45,000 l/h
- Overall length 3,910 mm
- Overall width 1,470 mm
- Overall height 1,650 mm
Jumbo 4
- Power 45 kW
- Max rotation 3,350 rpm
- Max centrifugal force 2,950 xg
- Slenderness ratio 5.12 L/d
- Bowl diameter 470 mm
- Water flow rate 55,000 l/h
- Overall length 4,385 mm
- Overall width 1,470 mm
- Overall height 1,650 mm
|
|
Centrifugal Extractor Baby series
Baby 1
- Power: 5.5 kW
- Max rotation 5,200 rpm
- Max centrifugal force 3,500 xg
- Slenderness ratio 2.48 L/d
- Bowl diameter 232 mm
- Water flow rate 2,500 l/h
- Overall length 1,700 mm
- Overall width 785 mm
- Overall height 1,090 mm
Baby 2
- Power: 7.5 kW
- Max rotation 5,200 rpm
- Max centrifugal force 3,500 xg
- Slenderness ratio 3.33 L/d
- Bowl diameter 232 mm
- Water flow rate 4,000 l/h
- Overall length 1,900 mm
- Overall width 785 mm
- Overall height 1,090 mm
Baby 3
- Power: 7.5 kW
- Max rotation 5,200 rpm
- Max centrifugal force 3,500 xg
- Slenderness ratio 4.12 L/d
- Bowl diameter 232 mm
- flow rate 5,500 l/h
- Overall length 2100 mm
- Overall width 785 mm
- Overall height 1,090 mm
|
|
Mammoth 2
- Main motor power: 70/100 Kw
- Drum revolution max: 2700 rpm
- Centrifugal force max xg.:2350
- Slenderness ratio L/D: 3,92
- Drum diameter:570 mm
- Hydraulic capacity: 65,000 l/h
- Weight: 5.540 kg
Mammoth 3
- Main motor power: 80/115 Kw
- Drum revolution max: 2700 rpm
- Centrifugal force max xg.:2350
- Slenderness ratio L/D: 5,10
- Drum diameter:570 mm
- Hydraulic capacity: 85,000 l/h
- Weight: 6.520 kg
|
|
Jumbopress 1
- Motor power 37 kW
- Overall length 3,000 mm
- Overall width 1,470 mm
- Overall height 1,650 mm
Jumbopress 2
- Motor power 45 kW
- Overall length 3,500 mm
- Overall width 1,470 mm
- Overall height 1,650 mm
Jumbopress 3
- Motor power 52 kW
- Overall length 3,910 mm
- Overall width 1,470 mm
- Overall height 1,650 mm
Jumbopress 4
- Motor power 52 kW
- Overall length 4,385 mm
- Overall width 1,470 mm
- Overall height 1,650 mm
|
|
Horizontal DECANTER centrifuge for continuous separation of solids from liquids such as thickening and dewatering sludge, suspensions with granular solids, clarification of liquids, classification of fine pigments, etc. Flottweg provides a broad range of DECANTER sizes, from pilot scale or small production up to industrial scale with capacities of 200 m³/h.
Typical DECANTER applications:
dewatering and thickening of sludge form municipal and industrial waste water, production of plastics (PVC, HDPE, etc.), recovering of animal and vegetal basic products (oils/fats, starch, proteins) beverages (wine, beer, fruit/vegetable juices)
|
|
Horizontal decanter centrifuge for continuous separation of 3-phase systems consisting of two immiscible liquids and solids. Flottweg provides a broad range of TRICANTER® sizes, from pilot scale or small production up to industrial scale with capacities of 80 m³/h.
Typical applications:
oil sludges, recovery of animal /vegetable oils and fats, wheat starch/gluten separation, etc.
|
|
Big tasks that need big solutions use disk filters.
High yield and product quality, combined with low production costs, provide the producer of bulk materials with a decisive competitive edge.
The Krauss-Maffei disk filter, based on many years of experience and countless applications, gives you an efficient filter operation to achieve these attributes.
These filters boast a tried and tested technology - and one that you can rely on day after day.
Features of the Krauss-Maffei Disk Filter a
- Large disk diameter increases the filter area.
- Increased number of filter cells reduces cell volume and substantially improves hydraulic efficiency.
- Easy filter bag installation with quick connect clamps.
- Virtually 100% product discharge through pneumatic assistance.
- Lightweight filter cells simplify replacement.
You benefit from a higher filtration capacity with better product quality and easy maintenance.
Main Applications:
Aluminum hydrate, clean coal, refuse coal.
|
|
|
The MASTER is a range of high head and high-efficiency gravity filters which use non-woven fabric filters. The MASTER range is able to treat between 200 and 1000 litres of neat oil per minute and from 400 to 2000 litres of water-based emulsions per minute containing both metallic and non-metallic particles. The entire filtration process is completely automatic.
|
|
Simplex Plastic Basket Strainers
1/2" to 8" - PVC, Corzan® CPVC and Eastar®
Duplex Plastic Basket Strainers
1/2" - 4" - PVC, Corzan® CPVC and Eastar®
Duplex Plastic Basket Strainers
6" - 8" - PVC & Corzan® CPVC
Plastic Y-Strainers
1/2" to 4"- PVC - Clear PVC and Corzan® CPVC
Y Strainers - Clear PVC
1/2" to 2"
|
|
Streamline-Duplex-System
- The technical advantage of single streamline systems
- Double volume compared to single system
- Single cover lid with eye bolts
- Filtration efficiency up to 98 %
- Compact Design
- Ready to connect
- Adjustable mounting legs
Specifications
Max. Flow-rate: 80 m³/h
Filter area: 1
Volume housing: 60 Liter
Weight housing: appr. 110 Kg
Installation height: appr. 180 cm
|
|
*High-acid solid core design
*Flow capacities from 1/6 through 2 1/2 tons
*Access valve to check system pressure or charge through
*Applications include refrigerators, freezers, ductless A/C and PTAC units
|
|
- Designed for system clean-up
- 500 hours salt spray protection
- high capacity acid retention desiccants
- shortest system cut-out lengths allow installation in tight areas
- Low pressure drop-highest effective filter area
- Two access valves simply pressure drop measurement
- solid copper sweat fittings
|
|
The range of filter driers cover both hermetic filter driers and filter driers with exchangeable core.
The hermetic filter drier is delivered with various functions: standard filter drier, bi-flow filter drier, combi filter drier and burn-out filter drier.
For the filter drier with exchangeable core the program cover: standard core for CFC / HCFC, standard core for HFC, burn-out core and mechanical filter. The filter drier housing is available with 1 to 4 cores.
|
|
Liquid line and suction line filter-driers are often referred to as System Protectors because they remove harmful elements from the circulating refrigerant before serious damage results.
Keeping the system clean and free of foreign contaminants that can restrict the operation of valves, block capillary tubes or damage compressors is the best way to assure trouble-free operation. These contaminants can be solids, such as metal filings, flux, dust and dirt. Other equally menacing contaminants are solubles, such as acid, water, resins and wax.
No matter how many precautions are taken during assembly and installation or servicing of a system, contaminants can find a way into the system. Filter-driers are designed to protect a system during operation. It is the function of this all-important unit to remove those residual elements that can attack and eventually destroy the system components.
|
|
|
|
Liquid / solid separators: decanters, centrifuges, filter presses...
