|
|
|
|
|
|
MIG/MAG - conventional all-rounders and digital experts.
Our 1000 times tried and trusted step switch controlled machine series MIRA, SATURN and WEGA or the completely digital PHOENIX inverter machine series - it's your choice!
THE CONVENTIONAL ALLROUNDER - THE STEP SWITCH CONTROLLED MIG/MAG WELDING MACHINES MIRA - SATURN - WEGA
Tried and trusted more than a thousand times over: Robust, step switch controlled - specially designed for applications in trade and industry involving tough operating conditions. They offer universal applications thanks to the many different machine versions from compact/decompact and gas /water cooled through to various wire feed units. They also offer impressive, self-explanatory and intuitive operating concepts for varying requirements - the simplest possible operation for everyone!
PHOENIX - THE DIGITAL MIG/MAG PULSE WELDING MACHINES
This is our completely digital inverter range of machines with maximum simplicity and ease-of-use for all requirements from manual to complex automated MIG/MAG pulse and standard applications. The PHOENIX range promises maximum efficiency thanks to the low-spatter welding on all materials and application, perfect ignition and welding properties with 100 % reproducible results with maximum quality and optimised control interfaces for every application - and these machines keep that promise! It's up to you: PHOENIX PROGRESS - the ideal introduction to the digital machine range - or PHOENIX EXPERT - the high-end system for complex applications, and not just in automated systems. Whichever you choose, you will get pre-programmed welding tasks (256 JOBs) so that you can concentrate fully on your work. The portable design of the PHOENIX 300 also impresses with maximum mobility for assembly work. All in all, the PHOENIX range is ideal for robot, industrial bus and mechanised applications and documentation via optional interfaces!
|
|
Cold Metal Transfer (CMT), a new chapter in the history of welding. The TPS 5000 CMT is a fully digital micro-processor controlled inverter welding system that supports the Fronius CMT process. Besides MIG/MAG, the system is also suitable for TIG and electrode welding.
The innovation that the CMT process introduces is that wire feeding is integrated into process control. This makes it possible to reduce the amount of heat applied; and that means no spatter on the work piece join.
The TransPuls Synergic 5000 CMT with 500 A is ideal for applications in the automotive and automotive supplies industry, avionics and spaceflight, metal working and portal building. In fact, the system is suitable for any automated or robot assisted job. The typical fields of application are thin and ultra-thin sheet joins of 0.3 mm or more, MIG soldering of galvanized sheet metal, and steel/aluminum joints.
|
|
Metal Inert Gas welding and Metal Active Gas welding are the most widely used welding processes in the world today. The range of possible uses is especially wide in the case of the versatile MAG process, which is suitable for unalloyed, low-alloy and high-alloy base metals. This makes it ideal for use in both the production field and for repair welding. The MIG process, on the other hand, is used for aluminium and copper materials.
All in all, then, a highly versatile welding process.
|
|
|
|
|
|
SYNERGIC.PRO² 170-2 - 280-2
Gascooled machines with 2-roller wire feed units
170 to 280 A, excellent ignition properties, stable arc, integrated database with over 500 different programs, digital processor control with synergic characteristic curves, standard 2 step and 4 step operation mode as well as spot and intervall welding, electronically controlled and regulated wire feed automatic system.
The revolutionary Smart Machine Control
A unique regulation concept developed by REHM in a stepped system: The arc length is not only controlled by measuring the arc voltage and the welding current, but also by digital capture of the wire feed rate.
SDI Technology(Stepless Dynamic Induction)
Innovative electronic welding choke with ultra-fast automatic regulator, for excellent ignition properties and an extremely stable arc. The choke setting can also be modified manually using the stepless controls.
RSC - Realtime Speed Control
The digital monitoring and regulation of the wire feed rate, extremely precise and in real-time.
CCM - Characteristic Curve Memory
The comprehensive, integrated welding parameter database (CCM) contains the knowledge of experts with many years of practical experience. The combination of material, wire diameter and voltage level is used to pre-select the synergy parameters required for a successful welding process. During welding, the actual values are constantly compared to the process specifications and, if necessary, corrected instantly.
RMI - REHM Machine Interface
Sets the welding energy using the material thickness alone, all the appropriate welding parameters are then selected automatically.
|
|
|
Welding machines Varmig synergy are intended for welding by MIG/MAG method by using shielding gas. Recommended to be used for welding construction steel, CrNi steel and aluminium. Varmig Synergy machines are mostly found in car industry, machine and ship building as well in various workshops.Microprocessor control enables synergy working, possibility to set programmed or manual welding parameters, soft start, digital indicator of welding voltage and wire feeding speed
|
|
|
Welding machines Varmig are intended to weld by MIG/MAG method and by using shielding gas. They are suitable for use in workshops and repairs, especially by thin metal plates. Varmig machines enable exellent weld quality and possibility to use flux cored wire (VARMIG 1600P).
|
|
|
|
|
|
COMPACT 240M
COMPACT 270-310-360-364-410
Aseries of industrial semiautomatic welding equipment with built-in wire feeder, suitable for professional and industrial applications. COMPACT power sources, in their innovative and user friendly design, ensure excellent welding characteristics on any material, aluminium and stainless steel included, by granting a very stable arc in any welding position. Robust and easy-touse, COMPACT power sources are suitable to be used in industry, fabrication work, car body repair, agriculture and maintenance.
- Excellent welding performance on any metal and thin lamination sheets
- QBS Feeding Motor Quick Brake System for constant and repeated arc striking
- Quick connection for the ground cable
- Innovative and user friendly design
- Metallic main structure with shock-proof fibre compound front frames
- Control panel protected against accidental impact
- Large ergonomic handle for an easy manoeuvrability
- Sloping front control panel, easy to read and adjust and highly visible from any direction
- Standard version supplied with cylinder carriage and robust wheels
- Eye-bolts for easy lifting
|
|
The latest generation of welding equipment can be programmed with specific process preferences of your individual choice or for the actual welding processes. Based on a solid state power source, it weighs just 1/80 of the 70 year old ancestors but has more power. Our different plasma cutting equipment enables you to quickly and accurately cut all types of metals.
|
|
The JOKE® multiSpot technology has revolutionised repair and modification welding for tool and mould making. Easy, quick and safe – the ideal system for efficient on-site tool repair. Specially developed for pulsed welding
applications. Such fine and precise welding has so far only been possible with a laser.
|
|
Genesis 200 CLS
The Genesis 200 CLS is a welding inverter for MMA and TIG LIFT welding, offering exceptional performance with all types of electrode.
The 200 CLS offers stable arc welding with cellulose electrodes in all positions as well as light weight (only 16 kg) and compact dimensions for easy carrying.
The exceptional dynamic response of this generator, independent adjustment of the Hot-Start, Arc-Force, and Anti Sticking functions from 0 to 500% of welding current and the considerable voltage available allow you to weld with large diameter rutile, basic metal and stainless steel electrodes. Particular care has been taken to ensure excellent welding results with cellulose electrodes and with special electrodes for aluminium and cast iron.
Standard arc dynamics for welding with the most common electrodes, and special arc dynamics for welding with cellulose electrodes can be selected from the front panel. Further special settings can be made from the set-up menu.
|
|
|
Welding machines VARMIG SUPERMIG and VARMIG CLASSIC are intended to weld by MIG/MAG method and by using shielding gas. Used in workshops, repairs and industry. Mostly used for welding construction steel, and also aluminium and CrNi steel if using appropriate accessories and welding wire. Exellent welding quality can be achieved, also with using flux cored wire.
|
|
|
|
|
|
Handler® 125 EZ
Unique Single-Knob Control
The Handler 125 EZ has Hobart's unique Single-Knob Control making it the quickest and easiest wire welder to set up and use. Just plug it into 115 VAC, select the mild steel thickness with the Single Knob Control and you are ready to weld. The Handler 125 EZ comes ready to weld 18 gauge- 3/16 in mild steel with .030 in (0.8 mm) self-shielding flux-cored wire so no shielding gas bottle is required. Also designed to use .035 in (0.9 mm) flux cored wire with a .035 in (0.9 mm) contact tip.
Handler® 140
The Handler® 140 operates off 115 volt standard household current for maximum versatility. Comes ready to weld with or without shielding gas, no additional kit required. With an amperage output range of 25 - 140, it easily handles a broad selection of solid mild steel or stainless, flux cored and aluminum wires.
Handler® 210 and optional DP-3035 Spool Gun
Packed with Power in a Portable Case
The Handler 210 is the one portable MIG welder that has 210 amps of welding power for handling 3/8 inch mild steel and enough control for 24 ga. thin material. Designed to handle a variety of materials including mild steel, stainless steel, and aluminum.
IronMan™ 230
A powerful welding package
The IronMan™ 230 is a total redesign of the full-size MIG platform, outperforming the competition on arc quality, voltage control, duty cycle and value. It delivers 30-250 amps of pure power in a heavy duty cabinet. The arc of the new IronMan™ 230 is optimized to deliver a flawless weld, making spatter and post-weld cleanup almost non-existent.
|
|
K2680-1 Precision TIG 225 - Power MIG 140C One-Pak
Industrial Price: 3399.00 (USD)
Lincoln’s Precision TIG® 225 / Power MIG® 140C One-Pak includes everything you need for MIG, TIG and stick welding, making it ideal for general fabrication, automotive/ motorsports, vocational schools, serious hobby work, home projects and repair, sheet metal, farm and small shop welding. And it’s the perfect complement for welders that need TIG, MIG and stick portability in one easy-to-move, easy-to-store package.
Includes:
- Precision TIG 225 Ready-Pak (K2535-1)
- Power MIG 140C (K2471-1)
- Small Wire Feeder Welder Mounting Bracket (K2616-1)
- Dual Cylinder Cart (K2617-1)
- Stick Electrode Holder and Cable (K2374-1)
|
|
New! Auto-Set™ is a breakthrough control that automatically sets your welder to the proper parameters. Auto-Set offers all-in-one MIG, minus the guesswork! Simply set the wire diameter, set the material thickness, and start welding!
Manual Mode has the flexibility to manually set weld parameters for broader applications.
NEW! Smooth-Start™ patent-pending technology provides a smooth, spatter-free start. —The best starting machine in the small MIG category. No more pop-gun starts or spatter to clean up.
Durable cast aluminum feedhead incorporates dual groove quick-change drive roll and spring-loaded tension arm with calibrated tension knob, all designed to make setup easier and faster.
Thermal Overload Protection shuts down the unit and activates over- temperature light if airflow is blocked or duty cycle is exceeded. Automatically resets when fault is corrected and unit cools.
|
|
Gunslinger
* Reliable solid state contactor
* Energy-saving circuit in MIG mode keeps fan on only while welding, automatically shuts off 6 minutes after completion of weld.
* In MIG mode, hot-start feature ensures smooth arc starting for reduced spatter.
* In MIG mode, burn-back feature allows wire to burn back at end of weld to prevent wire sticking in weld.
* In MIG mode, can readily change polarity to run solid or flux-cored wires
|
|
|
DIGIMAG 380 is a MIG-MAG inverter welding equipment. Either air-cooled or water-cooled, it brings the flexibility to weld the widest range of industrial applications, meeting the requirements for both medium and heavy fabrication.
|
|
Varmig 400 T44 S
Robust design for the hardest working conditions
Synergy working mode
DSP microprocessor technology
Possibility to weld by using flux cored wire up to 2,4 diamter
Improved function ARC START for easier arc ignition
30 programme places for saving individual welding programmes
ECO MODE working mode - minimum energy use by preparation state
EXT digital remote outer digital remote control connection possible
External UP/DOWN - welding power regulation through torch keys
PPN-D5 special version for better field movement
Interconnection cables up to 40m (above 15m only water cooled versions)
ARC TIMER - effective welding time measurement (option)
ARC LIMITER - welding current limitation (option)
|
|
GLC 351/451/551-C
Fine power adjustment
Robust and modular design
Measuring devices:
For welding current and welding voltage
Wire burnback
Adjustable via potentiometer
Standby operation
For cooling pump and fan
|
|
|
|
|
|
MIG
Step-regulated industrial MiG/MAG
MIG is a range of robust, step-regulated, user-friendly and all-round machines for MIG/MAG dip-transfer or spray-transfer welding, from sheet metal and light structures to thick walls. Primarily develop-ed for mild steel but also applicable for stainless steel and aluminium.
MIG machines:
Many variants
There is always a MIG machine with high duty cycle for inten-sive quality welding day after day. Some models are supplied as C (compact) versions, others as STB versions (STB for separate wire-feed unit) and with option-al air-cooling or water-cooling.The many variants are designed based on the four primary models: MIG 305, 385, 445 and 545. The largest models feature four choke connections and up to 36 voltage steps.
The strong choke spool ensures fine ignition in dip-transfer welding and makes it possible to weld with solid or flux-cored wires in dimensions from 0.8 mm.MiG 385 STB MiG 445 STB MiG 545 STB 3 x 230 V/400 V 3 x 230 V/400 V 3 x 230 V/400 V 40-385 A A 40-445 A 40-545 A Energy-saving standby function for water pump/fan.MIG is supplied with several variants of both open and closed types of wire-feed units featuring four-spool drive and quick change of wires and spools. It is possible to use small or large wire spools or to feed wire from a drum.
|
|
|
|
|
|
PSM 708
The PSM 408, PSM 508 and PSM 708 models are synergic power sources with electronic technology. The dynamics of these systems have been carefully studied for MIG/MAG continuous wire welding on carbon steel, stainless steel and aluminium, in both Short-Arc and Spray-Arc mode.
The models PSM 408-508-708 are provided with complete functions for Mig/Mag welding in manual and synergic mode, and guarantee optimal welding dynamics. The SCR electronic technology with digital control provides accurate linear regulation of the welding current voltage, permitting easy parameter regulation even at a distance.
Optimal starts (Hot-Start Mig Soft-Start and Burn-Back) and above all safety and dependability in all operating conditions.
The SYNERGIC control panel with numerous programs stored, makes these power sources extremely simple to use and suitable also for non-expert personnel. The Auto-Setting device allows the power source to automatically compensate for mains voltage variations, maintaining welding arc stability. The current and arc voltage values are shown on the digital display and at switch-off the last welding condition is stored.
The synergy permits automatic optimal setting of all the parameters, with extreme simplicity. All you have to do is determine, according to the type of material/gas used and the wire thickness, the ideal program in the table of synergic curves and then set the value of one of the following parameters: material thickness, welding current, wire speed.
|
|
|
|
|
|
BOOSTER.PRO 170/210
The uncomplicated operation using a rotary knob for welding current setting and a push button for the functions of TIG and manual Stick electrode (MMA) welding is new. The active function is indicated by an LED.
The INTIG (Intelligent Ignition Energy) selects the correct striking current automatically when electrode welding.
Soft and precise arc striking is ensured by the Lift-Arc ignition.
The REHM ELSA System (Electronic Stabilised System) prevents weld drop-outs and fluctuations even with input power cables as long as 100m (1,5 sq.mm).
The Arc-Force and Anti-Stick functions prevent accidental sticking and overheating of the electrode.
A temperature controlled fan switch automatically optimises the cooling power and reduces noise emissions and power consumption.
Suitable for use with a generator.
Powerful electrode welding in the Booster function, welding of Aluminium electrodes and multi-component Bronzes with the Arc-Force function.
Comfortable TIG welding in DC operation through the gas management function and the 4 step (latch-on/latch-off) function. (BOOSTER.PRO 170 with Gas management option).
|
|
RAINBOW 170 HF
RAINBOW 200 HF
RAINBOW 170 HF and digital control RAINBOW 200 HF represents the latest evolution of inverter DC welding machines.
These powerful 100 KHz power sources, based on the very latest IGBT technology and fitted with flat transformer, can be used for TIG welding of any metal, excluding aluminium and its alloys. RAINBOW 170 and 200 HF, which also perform very well in MMA welding , thanks to their light and compact size and excellent welding characteristics, are the ideal solution for maintenance, assembly and light fabrication works.
|
|
|
|
|
|
Navigator
Mobile TIG and MMA inverter
The Navigator is a range of robust and mobile universal welding machines for TIG and MMA welding operations.
All Navigator TIG machines are available with a trolley and an integrated cooling unit and are
equipped with energy-saving standby functions.
In TIG welding, the Navigator can switch between HF or LIFTIG® ignition. The power module keeps the arc stable during the welding process, thereby enabling the use of the Navigator in environments
where electromagnetic noise is critical.
Navigator welding machines:
Navigator 2500 AC/DC, which can also be used for MMA welding, features high-frequency ignition and built-in pulse, slope
and idle current functions. It performs quality welding in sheet metals using pointed tungsten elec-trodes.
Navigator 3000 (300 A welding current for 16 A fuses) is available in three variants:
Navigator 3000E uses covered electrodes to weld in steel and stainless steel.
Navigator 3000 DC HP is for TIG welding in mild and stainless steel.
Navigator 3000 AC/DC is for TIG welding in alumi-nium and aluminium alloys plus all other
DC weldable materials.
|
|
|
MMAW, SAW and MIG/MAG welding units for welding up to 1400 A DC as well as Kjellberg Finsterwalde welding automats are suitable for manual, mechanised and semi-automated welding processes.
|
|
Manual Metal Arc welding, also known as manual electrode welding, is a process with which virtually all metals can be welded. This process is also excellent for outdoor use. Incidentally, most of our MMA machines also permit TIG welding.
Manual electrode welding is a very widely practised and easy-to-use welding process.
|
|
|
|
|
|
The Ranger® 305 D is a powerful stick, TIG, and wire welding engine driven welder that is ready for all day, everyday performance on construction, maintenance or pipe applications. Rugged and dependable, the Ranger® 305 D is built with a totally enclosed case for maximum protection; Lincoln's Chopper Technology™ for an arc operators appreciate; and a 12 gallon fuel tank that will last you through the entire day. Lincoln's Ranger® 305 D ... it's ready for a workout.
Advantage Lincoln:
- Diesel Engine-Driven Welder
- A powerful 300 amp DC CC/CV diesel engine-driven welder. All rated outputs at 100% duty cycle 104°F (40°C).
- Multi-Process Welding
- Excellent DC multi-process welding for general purpose stick, downhill pipe (stick), TIG, cored-wire, MIG (CO2 and blended gas) and arc gouging.
- Digital Weld Meters
- Digital weld meters for amps and volts make it easy to precisely pre-set your procedures and monitor actual welding output.
- Superior Arc Performance
- Lincoln®'s Chopper Technology provides easy starts, a smooth arc, low spatter and excellent bead appearance.
- Plenty of AC Generator Power
- A portable powerhouse - delivers 10,000 watts peak (9,500 watts continuous) of 120V/240V AC generator power. Enough power to run lights, tools, and weld at the same time!
- AC generator voltage is constant at 120V or 240V at any weld dial setting.
- Skewed Rotor Design
- Skewed rotor design provides AC power waveshape suitable for operating Lincoln® Pro-Cut® plasma cutters and inverter power sources. Lincoln was first in the welding industry with this feature.
|
|
Diesel-Powered Welder/Generators
These diesel-powered welder/generators feature smoother arc characteristics and more consistent, quality welds. Multiquip's simultaneous operation models range from 180 to 500 amps as welders and 3 to 14kW as generators.
|
|
Powerful plasma welding machine for maximun weld seam quality
Precise, high stability plasma arc for targeted and concentrated heat feeding
High welding speeds, deeper fusion penetration, low material distortion
Consistent results thanks to the separate inverter for the pilot arc current
Optimum protection of the plasma welding torch from the integrated coolant flow monitor
|
|
Ace Plasma welder
Ensures high-quality, high-speed welding of galvanized sheet iron.
Combines the quality of TIG welding with the intensity of plasma welding to answerthe call for automation and efficiency.
150PK3, 200UPK2
|
|
The SGC 66 Percussion is a new generator which can weld is in
contact mode is in percussion mode.
It is the most compact generator and lightest in its category.
Managed by Microprocessor, it is equipped with a meter
of recording (counting of the number of weldings and time counting).
It is the ideal tool for all the weldings on stainless steel,
aluminum, brass, coppered mild steel, in the diameters m2 in M8, and
it finds its place in very many applications:
aeronautics, fine sheet-iron works, electric household appliances, articles domestic,
automotive engineering, cycles.
|
|
|
|
Welding stations
