|
|
| Products 91 to 120 of 198 |
|
Has particularly good adhesion to many difficult to bond substrates such as EPDM rubber, aluminum and flexible vinyl. It is economical to use because only drops of adhesive are needed to develop strong bonds.
|
|
The UV Light Cure ® resins are one component products that cure in a few seconds under ultraviolet rays. They are intended, for the most part, for the assembly of translucent materials like glass and transparent plastics (PMMA, PC...). On top of their curing speed, the Light Cure® resins are ideal for high production speeds. For the most pari they will give a perfectly transparent jointing, of optical quality, with extreme resistance and excellent protection against Chemicals.
The polymerization takes place in a few minutes to a fraction of a second. AEC adapts the priming of the resins, and thus the timing of the operation and the application to the base. The glues go from liquid to extremely sticky thixotropic.
|
|
|
DYMAX light-curable adhesives cure in seconds upon exposure to longwave ultraviolet light and/or visible light. Light-curable adhesives optimize the speed of automated assembly, enable 100% in-line inspection, and increase product throughput. Industrial adhesives are available for plastic sealing, metal bonding, and glass assembly, as well as for joining dissimilar substrates.
|
|
Advantages of Vitralit® UV and light curing-adhesives:
Easy handling
Short curing time for higher productivity
Solvent-free, no heat exposure
Long storage at + 5° c
Very good electrical properties
|
|
3M Scotch-Weld™ Hot Melt Adhesives and Applicators are advanced hand-held systems to help you improve productivity, lower cost, and minimize waste.
3M™ Scotch-Weld™ Hot Melt Adhesives are 100% solids thermoplastic resins that become fluid when heated. They cool, harden and reach bond strength in seconds, which keeps your production lines flowing.
|
|
NORPOL FI-177-10 is a low exotherm, light-weight sandwich adhesive, based on a high quality ISO/NPG resin. NORPOL FI-177-10 is accelerated and changes colour from light blue to white shortly after the admixing of peroxide.
•Recommended peroxide dosage: 1.5% low exothermic Peroxide (NORPOL PEROXIDE 19)
•Recommended application temperature interval 18-23 ºC
VARIOUS PROPERTIES
NORPOL FI-177-10 is mainly used to bond single core material sheets together and for bonding core material to GRP laminates.
NORPOL FI-177-10 is formulated for use in vacuum bagging.
The bonding paste should be stored at 18-25 ºC .If the product have a temperature <18 ºC (which is no problem as to product quality) it should be heated to 18-25 ºC before use. See storage and handling document of NORPOL products.
AVAILABILITY
Europe / Middle East / Africa
|
|
|
Acrylic and methacrylic acid-free, activator-curing structural adhesives brought about the technology revolution, known as "cold bonding", to the magnet and motor assembly industries. These structural adhesives are ideal for choke and transformer bonding, DC motor assembly, alternator, and flywheel applications, tacking, unitizing, ruggedizing, sealing, and shallow potting. This revolutionary resin chemistry has drastically shortened assembly times and saved space, labor, and regulatory compliance costs to make automation easier for manufacturers.
|
|
Marine – Sealants and Adhesives
LJF® proposes innovative solutions to clients in the area of Sealants and Adhesives and offers a product line fulfilling the specific requirements of the Marine market.
LJF® is present throughout the world in the area of bonding and sealing in varied markets and is recognized as a specialist in hi-tech products.
The experience of LJF® in the bonding and sealing of windows, portholes, the assembly of composites and other substrates, enable it to provide solutions adapted to customer needs in terms of technical performance, safety and environment.
In cooperation with sales teams, the R&D laboratories are attentive to customer needs. They develop and improve products by providing them with the latest technological advancements.
The Marine sector product line provides solutions to principal applications such as bonding glass, assembling and bonding a variety of materials, deck caulking, etc.
|
|
|
DYMAX UV and visible light curable adhesives for medical devices significantly reduce assembly processing costs. They cure within seconds upon exposure to UV and visible light and permit bonding of UV inhibited and tinted plastics. In-line inspection of the adhesive bond line is made possible with the patented fluorescing chemistry. DYMAX medical device adhesives are solvent-free and glow brightly when exposed to a low intensity "black light" and enhance the function of automated vision equipment for high speed, high volume production. These products are ISO 10993 approved and are ideal for bonding a wide variety of substrates found in catheters, reservoirs and housings, respiratory devices, needles and syringes, tube sets and fittings and other medical disposables. DYMAX MD® adhesives are compatible with gamma, EtO and E-Beam sterilization.
|
|
|
|
|
|
Master Bond Inc. is a leader in the design, formulation and manufacture of adhesives, sealants, coatings and potting compounds for the assembly of both disposable, reusable and implantable medical devices. Master Bond’s product line includes epoxies, urethanes, silicones, cyanoacylates, and specialty solvent based systems. These products can be cured at ambient and/or elevated temperatures or by exposure to UV light. Specific formulations fully meet the USP Class VI protocol. Master Bond’s technical staff welcomes the opportunity to provide assistance to medical device manufacturers in the solution of specific assembly problems.
Master Bond's compounds can simplify and enhance the performance of many critical medical devices. Formulations have been developed which offer high physical strength properties and outstanding chemical resistance even when applied on dissimilar or difficult-to-bond materials. Additionally, selected products retain their desirable performance upon exposure to various sterilization procedures including autoclaving, radiation, ethylene oxide and the recently developed cold sterilants. These compounds can be used in a wide variety of devices such as diagnostic instruments (endoscopes, etc.), surgical tools, catheters and implantables.
|
|
Excellent bonding with vitralit® UV-/light curing adhesives:
Outstanding resistance against all current sterilization processes
Very good bonding on several plastics and metals
Solvent free
1-Component cyanolit® Instant adhesives
Fast curing
Solvent free
Excellent dispensing properties in automated systems
|
|
|
Master Bond Inc. formulates a wide range of one and two component adhesive systems for bonding metals. From aluminum to cast iron to stainless steel to titanium select Master Bond for your specific needs. They will speed productivity, reduce waste, save energy and enhance produce capabilities. Job proven for over 30 years, Master Bond products are employed in industries ranging from aerospace, optical and electronics to oil/chemical processing, medical and automotive.
|
|
No Grinding or Surface Preparation
Plexus Adhesives bond engineered plastics, SMC, FRP, metals, and dissimilar substrates without grinding, surface preparation, or primers. As a result, they eliminate time-consuming and costly operations, lessen process variability, minimize dust, and greatly reduce the problems associated with toxic solvents.
|
|
|
|
|
|
Master Bond formulates a wide selection of metal charged adhesives for numerous industries. Theses include metal repair adhesives with aluminum and stainless steel fillers.
Master Bond’s line of electrically conductive adhesives is the number one choice for the design of tomorrow’s advanced electrical circuitry. Nobody offers more choices or solutions. The Master Bond product line includes silver, nickel, copper and graphite filled compounds. We even offer silver coated nickel systems for low resistance where cost effectiveness is crucial. Specific compounds are designed to cure at ambient temperatures or upon brief exposure to elevated temperatures. The cured products offer high physical strength, superior substrate adhesion and uniform electrical conductivity even upon exposure to hostile environmental conditions. Long term durability is excellent.
Master Bond also manufactures one and two component thermally conductive systems. They include epoxies, silicones and other elastomeric systems. Special formulations for unusual service conditions are available. They include serviceability to 500°F, at cryogenic temperatures, and in high vacuum environments as well as systems that are easily repairable. Designed for easy application, these compounds can be purchased in convenient packaging. They are used on heat sinks, fan sinks, package lids, motor controls, multiplexers, sensors, power semiconductors and thermistors. Toughened systems have been successfully employed in applications requiring resistance to shock, vibration and thermal cycling.
|
|
Stainless steel-filled epoxy putty for patching, repairing and rebuilding stainless steel food processing equipment
KEY FEATURES
* Non-rusting
* Bonds to ferrous and non-ferrous metals
* NSF certified for potable water applications
* Acceptable for use in meat and poultry plants
* Listed under NSN stock #8030-00-268-7934
|
|
|
French manufacturer of acrylic structural adhesives, AEC offers products resistant to fire, transparencies, high performances…
|
|
Aramid and leather, textiles and membranes, or synthetic and aluminized materials: Collano special adhesives - elastic, tear-resistant, weatherproof - bond the most diverse materials. Moreover, they introduce a new quality to the end product resulting in greater reliability, greater comfort and greater appeal, whether in outdoor clothing, fire protection, filtration or roofing.
With Collano adhesive systems the target "Bonding instead of Sewing" will be realised.
Easy processing, high performance, and improved efficiency are among the key characteristics of Collano adhesives:
Thermoplastic adhesive films
Reactive adhesives (UV- or moisture-curing systems)
Unique: the thermoreactive, pre-applyable PUR Collano® HCM
Hot melts
Dispersions
|
|
|
|
|
|
BUTYL SEALANTS
Polylok’s joint sealant system is custom engineered to meet the most exacting standards of the pre-cast concrete industry. Polylok Butyl Joint Sealant remains flexible and forms a permanent bond to a wide variety of substrates including concrete, metals and plastics. Adhesion and cohesion at the time of installation are excellent, and actually improve after the joint has been formed and placed in service. This sealant is designed not to shrink, oxidize or harden and has excellent resistance to temperature extremes, acid and alkaline environments. Polylok’s Butyl Joint Sealant is designed to fully comply with current ASTM Standards and specifications as required by Federal, State and Local agencies for use by the precast concrete industry and contractors. Available in sizes: 1/2'' x 21'', 3/4'' x 21'', 1'' x 21'', 3/4'' x 14.5'', 1'' x 14.5''. Special Sizes Available Upon Request.
PRODUCT FEATURES:
- Available in strip or coil form
- Non-stick, non-tear plastic backing
- New crush-proof packaging
PRIMARY APPLICATIONS:
- Concrete Pipe
- Utility Vaults
- Septic Tanks
- Sanitary & Storm Sewer Manholes
- Box Culverts
- Burial Vaults
- Wet Wells
- Concrete Wall Panel Systems
|
|
WEICON Flex+bond distinguishes itself by its wide range of application possibilities and the high adhesive force.
It bonds and seals nearly all materials such as metals, wood, plastics, glass, cera mics to themselves and among each other and is therefore the excellent product for a great variety of repairs and bondings as well as for the sealing of seams and joints.
WEICON Flex bond is a one-component product, remains permanently elastic and can be sanded after curing and overpainted (wet in wet).
WEICON Flex bond is
. permanently elastic
. temperature resistant from -40°C (-40°F) up to 90°C ( 194°F),
. briefly (2-3 hours, except transparent) up to 130°C ( 266°F)
. resistant to weathering and UV rays
. resistant to salt water
. neutral in odour
. overpaintable immediately (wet in wet)
. cures nearly shrinkage- and bubbling-free
. sandable
. resistant to ageing
. free of isocyanate and solvents
. free of silicone, halogen and PVC
|
|
|
|
|
|
For ease of application and outstanding performance, choose Master Bond one part, heat curable epoxy systems. They are designed to save time, improve efficiency, eliminate waste and enhance reliability. These systems are pre-catalyzed and require only moderate heat to cure. This avoids the need to mix two components which can result in air entrapment. To prevent such problems, two part epoxies often must be mixed in a vacuum environment. Additionally, two component systems often have multiple mix ratios i.e. 10 to 1 by weight, etc. and limited pot lives. This often leads to errors. One part, no mix systems alleviate inaccurate mixing and eliminate wastage from non-use of compounds in specified time periods. Furthermore, the speed of cure is rapid — often faster than two component systems.
Master Bond offers an extensive variety of one component epoxy systems. They are available in small to large quantities and are freshly prepared to ensure maximum shelf life. We use the most advanced polymers and our technology is cutting edge. Special formulations are cryogenically serviceable, castable over 1 inch thick, machinable, electrically conductive, thermally conductive and have superior tensile strength properties. Additionally, NASA low outgassing approved systems and compounds that meet USP Class VI requirements are also available.
|
|
|
WEICONLOCK® products are high quality anaerobic adhesives and sealants on the basis of special methacrylate resins, especially made for economical threadlocking, retaining and sealing of threaded, cylindrical and pipe assemblies. WEICON Contact are cold-curing one-component adhesives, free of solvents. They quickly polymerise by reacting with moisture both on the surfaces to be bonded and from the air, and cure under light pressure.
|
|
|
|
|
|
Optical systems offered by Master Bond include both one and two component epoxy resin compounds and one component UV curable compositions. The epoxies are specially formulated to maximize resistance to water and other adverse environments. Features of the optical systems offered by Master Bond are excellent light transmission characteristics, superior non-yellowing properties along with a wide range of systems where the index of refraction ranges from a relatively low 1.43 up to 1.61. The ultraviolet compositions cure tack free in the presence of air. Formulations have been carefully processed to exclude potentially objectionable contaminants as chlorine and other halogens as well as sodium and related elements. They provide innovative solutions to the many processing problems of the optical industry and virtually eliminate quality control difficulties caused by corrosion and other environmentally induced conditions.
Applications range from bonding and potting fiber-optic cables, connectors and terminations, upgrading the vibration and shock resistance of electro-optic assemblies, cementing and coating optical parts, potting LED devices, optical replications, bonding ferrules and connectors, and coating or encapsulating a wide variety of electro-optic and laser components.
|
|
|
DYMAX light-curable adhesives cure in seconds upon exposure to longwave ultraviolet light and/or visible light. Light-curable adhesives optimize the speed of automated assembly, enable 100% in-line inspection, and increase product throughput. Industrial adhesives are available for plastic sealing, metal bonding, and glass assembly, as well as for joining dissimilar substrates.
|
|
Advantages of Vitralit® UV and light curing-adhesives:
Easy handling
Short curing time for higher productivity
Solvent-free, no heat exposure
Long storage at + 5° c
Very good electrical properties
|
|
one-component acrylates
light-curing, UV-curing (see "curing lamps DELOLUX")
Bonding of modern materials and changed production processes are enabled and supported by continuous redevelopment of DELO-PHOTOBOND products.
Bonding of various raw materials of mobile loudspeakers
The loudspeakers' high quality is ensured by optimum, acoustic properties. High output by shortest cycle times. Bonding of aluminium door hinges onto glass shower cabins
Boreholes or unsightly clamping fixtures are prevented.
Properties DELO-PHOTOBOND:
graded elasticising from hard to tension-equalising enables
bonding of various materials for different requirements
curing within seconds allows short cycle times
Application areas:
Communications electronics
Consumer electronics
Automotive electronics
Plastic and glass processing
You can find detailed information about radiation curing in our brochure „Radiation curing“.
|
|
|
|
|
|
Master Bond photoinitiated adhesives are part of a fast growing family of one component UV curable adhesive systems for high performance coatings, adhesives, sealants, potting and encapsulation. These UV and EB radiation curing adhesives include polyurethanes, epoxies, polyesters and acrylics. UV adhesive grades vary in thicknesses, hardness, chemical resistance, strength, clarity, etc. When exposed to a suitable UV light source, UV curable compounds usually cure in a matter of seconds. The Master Bond UV cure products are not oxygen inhibited and cure at ambient temperatures. Environmentally friendly, they are 100% reactive liquids which do not contain any solvents or other volatiles. Upon cure they exhibit minimal shrinkage. Additionally, they are strong, durable, and offer superior temperature and chemical resistance. If required, special formulations can be developed to best meet specific product application and performance needs. One new "dual cure" adhesive compound can be cured by exposure to either UV light or heat.
Master Bond UV curable coatings and adhesives are one component systems and require no mixing. They have a long shelf life when stored at ambient temperatures in the absence of UV light. They have excellent bond strength to metals, ceramics, many plastics and most rubbers. UV curing sealants adhesives and encapsulants are particularly suitable for automated continuous manufacturing processes because of their fast cure speeds.
|
|
one-component epoxy resins
curing is triggered by UV or visible light
(see "curing lamps DELOLUX")
Preactivation and curing within seconds result in:
rapid and secure bonding even of non-transparent
components
shortest cycle times
rapid further processing
Dam & fill® products for smart cards
This protects the sensitive chips. Fixing soldered contacts of electronic components
The adhesive provides secure protection against unsoldering and strong shocks
Properties DELO-KATIOBOND:
dry surface
outstanding ahdesion on different materials
good tension-equalizing behaviour
low-viscous to pasty
Application areas:
Micro-electronics
Electronics / electrical engineering
Automotive supplier industry
Smart Card industry
Plastic processing
You can find detailed information about radiation curing in our
brochure „Radiation curing“
|
|
NORPOL FI-170 is a multi-purpose bonding paste based on special polyester resins combined with selected fillers and additives.
NORPOL FI-170 is pre-accelerated and has a white colour. NORPOL FI-170 changes colour from bluish white to white in <5min. after the admixing of peroxide.
•Recommended peroxide dosage: 1.5% MEK Peroxide (NORPOL Peroxide 1)
•Recommended application temperature interval 18-23 ºC
•Sag/flow: Will not sag provided a maximum thickness of 15 mm is observed. Not horizontally self-flowing.
Applicable as a general purpose bonding paste.
VARIOUS PROPERTIES
Suitable surfaces: Glass-fibre reinforced products and cellular plastics.
Workability: Hard to grind.
The bonding paste should be stored at 18-25 ºC. If the product is below a temperature of 18 ºC (which does not affect product quality) it should be heated to 18-25 ºC before use. See storage and handling document of NORPOL products.
AVAILABILITY
Europe / Middle East / Africa
|
|
The GRAVICOL® range of bonding pastes are designed for the assembly and bonding of glass reinforced plastic moldings. All of the bonding pastes in the range are pre-accelerated and require only the addition of a
standard MEKP catalyst. The pastes can be used for bonding two parts, insert panels, core materials. They can also be used for cavity filling and as an aid to lamination to help reduce the chance of air voids. When designing the bonding pastes there are several key areas we look at and control to
suit the numerous application areas of the pastes : - Gel/Cure Times - Low Shrinkage Levels - Application Methods - Mechanical Properties
|
|
Plexus Adhesives are used in a wide range of general assembly applications. They:
Bond plastics, composites, metals and dissimilar substrates
Produce bonds so strong that they can be used in place of mechanical fasteners
Require little or no surface preparation or primers
Reduce the need for chlorinated solvents
Are easily dispensed using hand-held dispensers or meter-mix equipment
Are mixed as dispensed, eliminating premixing and pot life considerations
Cure rapidly at room temperature without heating UV
Offer excellent flexibility and resistance to impact, fuel, and chemicals
|
|
|
|
Bonding, Adhesives
