|
|
| Products 121 to 150 of 234 |
|
Agroalimentary jack ICL Specific ISO 6431 Diameters: 32, 40, 50, 63, 80, 100 and 125 mm Races: 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500 (longer races on request) Corrosion resistant, including fixings Measurements according to the standards ISO Sensor easy to install and adjust
|
|
Extruded Flat Lift Table
EF1-based, guided cylinder with four shafts for maximum rigidity. It is designed for lifting applications where other non-rotating cylinders cannot handle an overhung load and space is at a premium.
Four-shaft support withstands offset loads and moments.
Simple, efficient design provides economical alternative to other costly guided actuators.
Joins the EF family of products, so shares all the same benefits--long service life, low friction operation, fast delivery.
Convenient wide tooling mounting surface.
Intended for vertical lifting applications (should not be mounted horizontally or with tooling plates facing down).
|
|
GeoSlide Series Guide Unit
The GeoSlide guide units utilizes Numatics GeoMetric ISO 6431 VDMA cylinders. The FHG & FHK series offers high load carrying capabilities in a metric package.
Features:
Bore sizes range from 32mm to 100mm.
Strokes up to 500mm.
Linear ball or bronze bushings option.
Available in a "U" style body.
LCX Series Linear Slide
The LCX Series linear slide combines cost-effectiveness with proven dependability. An economical alternative with greater load carrying capabilities.
Features:
Low Cost
High Load Capability
Stainless Steel Shafts Available
Engineered Plastic Polymer Bearing
Available in 3 Bore Sizes
|
|
Z Line Air Cylinders
The Bimba Z Line Air Cylinders are for extremely tough applications.
The Z-Line air cylinder has the rolled-in construction of the Original Line but features the following: Larger diameter, two-piece 303 stainless steel piston rod HEX-STUD rod end thread of heat treated alloy steel - easily removed in case of failure due to overload, and cushion quiet elastomer bumpers.
No charge options include the Magnalube G, Molycoated body, and magnet.
Bore sizes for the Z Line cylinders are 3/4", 1-1/16", 1-1/2", and 2".
|
|
Inflated with air or a fluid (water, oil, glycol...) depending on the application, PRONAL flexible lifting bags are pneumatic components which perform mechanical functions such as pushing, squeezing, guiding, clamping, blocking, damping, lifting, moving...
They are easy to incorporate within mechanical systems and are used in presses, moulds, conveyors, handling robots, lifting tables...
Advantages :
- thin when empty,
- compact,
- uniform lifting power
- very easy to adapt,
- high lifting force.
A highly diversified range of products
- standard square shape (100 to 1,000 mm in length), single or multi-stage, inflation pressure up to 7 bar (12 models),
- customized rectangular or curved shape, all sizes,
- multiple accessories which can be adapted to the environment.
Made from elastomer-coated fabrics, flexible lifting bags are vacuum vulcanised at a temperature of 140°C.
|
|
Hole Punch Cylinders
Designed to punch millions of holes in plastic or other thin sheet materials 2 to 3 mils thick, the long-life BIMBA Pneumatic Hole Puncher will give you more cycles per penny.
The hardened steel cutter with ground razor sharp edges is an integral part of the cylinder. A small air jet ejects the slugs from the cutter preventing slug build up, and Elastomer Bumpers insure cushion quiet operation.
Less than 1" in diameter, several cylinders can be closely mounted. Available in seven hole cutter sizes from 1 / 4 " to 5 / 8".
This stainless steel body, single acting spring return cylinder has a 3 / 4" bore and 1" stroke. A nickel plated steel rod guide is threaded for easy nose mounting, and a 1 / 8" NPT air inlet is conveniently located in the rear head.
Prelubricated with HT-99, the cylinder can be operated with ordinary shop air at pressures up to 250 psi.
|
|
Narrow Profile Air Table Actuators
The NPA actuator provides precise load guiding with a recirculating ball rail above its bore.
Two bearing styles are offered (single/double bearing block) to accommodate both lower cost and higher precision/cost applications.
With standard strokes up to 120mm, the NPA offers longer travel length than any competitive actuator of its type.
Bore sizes: 12, 20, 32mm.
|
|
Diameters 18, 25, 32, 40, 50, 63, 80 mm
Stroke length 10 ... 3,000 mm
Force 153... 3,016 N
Position sensing
Adjustable cushioning
Guide variants
- Basic guide
- Plain bearing guide
- Ball bearing guide
- Heavy-duty guide.
|
|
Diameters 8, 12, 18, 25, 32, 40 mm
Stroke length 1 ... 5,000 mm
Force 30... 754 N
Position sensing
Various cushioning options available
Guide variants
- Basic guide
- Plain bearing guide
- Ball bearing guide.
|
|
|
|
|
|
DLB-B/L - DirectConnect Internally Powered Base Slide
These highly configurable internally powered linear base slides reduce the mounting footprint over externally powered slides by up to 50%. They are available in multiple strokes & sizes. DIRECTCONNECT mounting makes assembling these units together a snap.
- Bulit-in repairable cylinder
- Compact for extremely small spaces (-B)
- Longer strokes in Compact Space Saving Package (-L)
- Features DIRECTCONNECT mounting
RFE - Feed Escapement
The RFE series of feed escapements offer failsafe locking fingers, sealed design to prevent internal component wear, and built-in sensor mounting slots. They are the most effective mechanism for separating components fed from a track or conveyor.
- Finger locking mechanism ensures that only one finger can be retracted at one time for proper part feeding
- Square shaft prevents shaft from rotating
- Unit can be mounted using top, bottom, or face surface
DLM - Mini Ball Rail Slides
- Up to 8 position sensing available.
- Recirculating Double Bearing Option
- Adjustable Precision Stops
- High Temperature Viton Seal Option Available.
DMM - DirectConnect Slide Mounting Modules
These pre-engineered mounting modules are designed to provide a simple and sturdy solution for mounting DIRECTCONNECT Base Slides and Thrusters. Select from 10 different design styles in 3 sizes. Simply specify style, beam size, and basic dimensions.
- Simple and sturdy solution for mounting DirectConnect base slides and thrusters
- Pre-engineered designs save you time and money
- Individual components allow you to design your own modules
- Customize with add-on kits and accessories
|
|
Parallel cylinder
for high loads and moments in every direction double action force
Technical Information:
· Designed flat and with double force, the Parallel cylinder with central port on the special end caps does also absorb higher forces. The yokes are aligned true a plate
· The load can be multiplied and the action force doubled by adjusting two rodless pneumatic cylinders parallel.
· The parallel cylinder can overall be used where big parts must be moved, e.g.
- workpieces on machining centers
- assembling machines
- transport systems
- stroke systems with limited adjusting length
· Port rotatable in the middle and upwards, inand outside
· Cushioned end positions are adjustable
|
|
Two Axes of Motion in One Housing!
Rigid Design Holds Guide Shafts at Both Ends
Deflection Under Heavy Loads is Greatly Reduced
Air Cushions Standard on 1" & 1.5" Bore Sizes
Precision Mounting Surfaces with Tooling Holes for Grippers and Tooling. Custom Faceplates are Available
Heavy Wall Cylinders Built Into Housing
Case Hardened Shafting
Composite Bushings or High Precision Linear Ball Bearings Provide Accurate and Repeatable Motion
Floating Couplers
Pre-Mounted Cable Carriers
Adjustable Shock Absorbers
Optional Threaded Stop Collars for Fine Stroke Adjustment
Dovetail Sensors with Optional "Quick Disconnect"
|
|
High rigidity and flexible fitting by highst precision in manufacturing. Flexibly expanding intermediate positions increase the possibility of applications.
|
|
MRS Cylinders
* The Bimba MRS® Magnetic Reed Switch Air Cylinders are specifically designed to operate Bimba position sensing switches to actuate programmable controllers, relays, solenoids, timers, or any other electrically operated equipment.
* MRS cylinders have an additional groove in the piston to accommodate a magnet. They differ from the Moption because they combine features of the "Z" line with Original Line construction. Type 303 stainless steel rods are standard.
* Options at no additional charge include Magnalube G, no thread, and switch track for standard reed switches.
* Bore sizes available are 9/16", 3/4", 1-1/16", 1-1/4", 1-1/2", 1-3/4", 2", and 2-1/2".
|
|
Linear Thrusters Pneu-Moment
For smooth, guided motion. A durable housing with guide shafts keeps our Linear Thruster from rotating and allows it to carry higher loads. Choose from two different models. A choice of stroke lengths and a wide variety of catalog options make the Bimba Linear Thrusters easy to use and ready to order.
The Benefits of the Linear Thrusters Pneu-Moment Include:
Bimba stainless steel body air cylinders for long, reliable life
Optional magnetic piston for use with Hall Effect or Magnetic Reed Switches
Optional adjustable cushions for smooth deceleration of load at end of stroke
Optional internal or external bumpers to absorb shock or adjust stroke
Easily accessible ports
|
|
|
High load weight vs extension. Five bore sizes from 3/4" (20mm) to 2" (50mm). Stroke lengths up to 12" (305mm), Base or side mount. Linear ball or composite bearings. Options include switches, shock absorbers, stop collars and bumpers.
|
|
The Two Shaft Linear Thrusters offer a compact design while offering maximum design flexibility. They feature two precision guide shafts that provide non-rotational linear guidance and high load capacity. Replaceable linear ball bearings are standard and provide long life, high load capacity and low-friction service. Optional composite bushings and chrome plated stainless steel guide shafts provide a solution for more challenging environments. A stainless steel option is offered for wash down applications.
The black anodized precision machined housings are designed for replaceable stainless steel or aluminum body nose mounted cylinders. Cylinder options range from magnetic pistons to dry service. Other options include position sensing, counterbored or tapped short or long tooling plates, auxiliary mounting plates, and external bumpers or hydraulic shock absorbers.
|
|
Pneu-Turn Actuators
The Bimba Pneu-Turn Actuators have cylinder bodies with 304 stainless steel for maximum seal life and an actuator body that's high strength, anodized aluminum alloy for maximum corrosion protection. The porting ends are high strength, anodized aluminum alloy.
The shaft bearings are self-lubricating, sintered iron copper material for lower friction and the piston seals run with Buna "N", U-cup type for low breakaway friction and long life.
Angle adjustment is an option that allows 45° of adjustability at each end and the adjustable cushions are an option that controls deceleration at the end of the rotation.
Torque factors include 9/16" bore, single rack; 9/16" bore, double rack; 3/4" bore, single rack; 3/4" bore, double rack; 1-1/16" bore, single rack; 1-1/16" bore, double rack; 1-1/2" bore, single rack; 1-1/2" bore, double rack; 2" bore, single rack; and 2" bore, double rack. The Pneu-Turn angles of rotation are 45°, 90°, 180°, 270°, and 360°.
|
|
|
|
|
|
Rotary Vane Pneumatic Actuators
Features
·Torque output of 16 to 1000 Inch Pounds
· Adjustable Rotations
· Reed and Hall effect switches
· Only one moving part
· Non Lube service
· Low cost solution
·Heavy Duty Double Acting Ball Valve Systems
Valve sizes from ¼” to 3”
140 in.lbs to 800 in.lbs
· Spring Return Valve operators
Single acting with spring close or open
Valve Operator Systems
·
·Spring Return operators are formed by bolting a spring return unit to a double acting Val-U-Act operator. The return movement is effected by a clock-type spring which is pretensioned to about half the operator torque. The amount of pretention is large, compared to the rotation and therefore the torque does not vary more than 20% over the rotation.
Spring returns are factory-installed and adjusted. The spring returns have a worm drive adjustment for setting or changing spring pretension. By inserting a socket key into one end of the worm the spring pretension can be very easily increased or decreased to suit operating conditions. To increase pretension, turn the worm clockwise; to decrease, turn counterclockwise.
|
|
Size 6, 8, 10, 12, 16, 25, 32, 40 mm
Torque 0.15 ... 20 Nm
Swivel angle 0 ... 270°
Position sensing
Fixed cushioning.
|
|
|
|
|
|
Product Details
Torque up to 5110 Nm
+-10 Deg End stroke adjustment
Double Rack and Pinion Design
Hard Anodized Power coated AL body
FEATURES
-Pinion supported on polyacetal Bearings
-Maximum Working Pressure 10 bar
-Lubrication is not necessary
-Temperature Range: -40 oC to +100 oC
-Life > 1 million Cycles
-Anti blow-out pinion
-Double acting can be converted to single acting just by adding springs
-Unique spring Retainer construction
-Ease of handling and enhanced safety while dismantling (especially in single acting)
-No lubrication required for springs
-Pre-compression leads to longer spring life
-Modular spring construction permits combination of springs (26 combinations) to generate optimum torque
-Spring can be assembled or dismantled easily because of extra long bolts on covers.
END STROKE
-Setting scews provided on the body
-±10o setting possible for closing and opening
-Strong Machined Cam for locking
'V' SEAL
-Low on co-efficient of friction
-Longer life, no lubrication needed
-Excellent response to control valve positioning due to low friction
ISO PAD
-Valve mounting as per ISO 5211 with an additional one higher size pad
-Standardisation of mounting accessories
-ISO centering Ring for precise location
-Octagonal drive shaft for ease of mounting
SPRING
-GR III epoxy coated Spring having high corrosion resistance
-Modular Springs set catering to various valve torque characteristics
-Life Time Lubricated
-Non Buckling Modular Spring design
|
|
Features
● Rotary cylinder with double rack and pinion
● High precision positioning
● Shock absorber is mountable
● Intergrated table and pinion (Rigidity)
● Various applications through round table
● Easy wire arrangement by hollow axis
● Auto switch is mountable
|
|
Pneumatic positioner for propotional acting :
The device positioner is particularly suitable to govern rotary actuators; used on butterfly or ball valves.
|
|
|
AGI offers a full line of pneumatic rotary actuators. All rotary actuators are rack and pinion design and incorporate output flange hard stop. The hardstops stops the output flange directly so there isn't any pinion breakage. The units are ultra hi torque pneumatic actuators due to cross porting the two piston bores. The extremely low profile package is excellent in tight space applications. There are five sizes available with manifold and mid stop options. Torque output ranges from 7in-lbs. to 310 in-lbs. @ 100 psi.
|
|
HRAPS
Rotary actuator-piston type offers maximum space saving, easy piping. Rotation from 90 degrees toa full 360 degrees. Ultra compact sensor switch can be used. Double rack system offers no backlash and no leak construction. Slim, compact body. One end porting allows greater space saving. Double rod model available.
|
|
Simple Design
Low maintenance, best dollar to torque output ratios available.
Single Moving Vane with a Fixed Seal
Simple and reliable design means less maintenance no hysteresis and extremely long life.
Patented Tri-Seal Design
Tri-Seal seals the output shaft, body halves and vane with a single molded polyurethane component. Reduce costs and lead time.
Pressure Assisted Seals
Sealing is inherently self compensating for wear because the air pressure creates the seal.
No Load Full Stroke Operation with Less Than 3 PSI Air Supply
Low friction means that almost all the plant air to the actuator is being utilized to operate the valve instead of overcoming the friction in the actuator. Puretorq vane type actuator is excellent for modulating applications.
Dual Output Female Drives Together with Dual ISO Mounting Pad
|
|
1 An uncontrolled reset stroke can cause some bounce of the rack and a small forward impluse to the shaft. It will be apparent only if the shaft load is small, with low friction. It can be reduced by a bumper (usable on reset cylinder only) or more by a correctly adjusted cushion
2. Switch mounts by strap to cylinder, place as required for access and signal phasing R (sink) or S (Source) switches only.
|
|
RR-Heavy Duty - Flange Output Rotary Actuator
This heavy-duty rotary actuator is ideal for payloads up to 200 lbs [91Kg] in weight. They are available in standard 45, 90, 135 or 180 degrees of rotation. Optional shocks/stops, mid-stop and rotary manifold available.
1. Low profile and bearing supported turn table provides an extremely compact package for tight space applications
2. Payload can be connected directly to the turn table. Eliminates the need for a bearing block
3. Zero backlash, preloaded ball bearings, and slip fit dowel pins make this a very precise and repeatable rotary actuator
4. Air manifold option eliminates twisted airlines
|
|
|
|
|
|
DRF - Flange Output Rotary Actuator
These new DIRECTCONNECT, flange mount rotary actuators, allow the payload inertia to stop directly through an independent hard stop mounted in the turntable, rather than through the drive mechanism.
- Infinitely adjustable within rotation range
- Dual bearing flange support
- Magneto-resistive sensing
- Adjustable hard stops
RR-Light Duty - Flange Output Rotary Actuator
This small, compact and lightweight rotary actuator is ideal for payloads up to 3 lbs [1.3Kg]. They are available in standard 45, 90, 135 or 180 degrees of rotation. Optional sealed flange or sealed flange with corrosion resistant hardware available.
- Low profile and bearing supported turn table provides an extremely compact package for tight space applications
- Payload can be connected directly to the turn table. Eliminates the need for a bearing block
- Zero backlash, preloaded ball bearings, and slip fit dowel pins make this a very precise and repeatable rotary actuator
- Air manifold option eliminates twisted airlines
RR-Heavy Duty - Flange Output Rotary Actuator
This heavy-duty rotary actuator is ideal for payloads up to 200 lbs [91Kg] in weight. They are available in standard 45, 90, 135 or 180 degrees of rotation. Optional shocks/stops, mid-stop and rotary manifold available.
- Low profile and bearing supported turn table provides an extremely compact package for tight space applications
- Payload can be connected directly to the turn table. Eliminates the need for a bearing block
- Zero backlash, preloaded ball bearings, and slip fit dowel pins make this a very precise and repeatable rotary actuator
- Air manifold option eliminates twisted airlines
|
|
|
|
Pneumatic cylinders
