|
|
Lifting devices
Lifting - Freeing - Cleaving
Mustlift is able to lift safely heavy loads on the ground or in water. Their compact size, allowing to place them quite everywhere, is obtained by a simple vulcanization of a high resistant elastomer coated fabric. They can be used on irregular surfaces thanks to their positive grip surface.
Mustlift lifting bags can be inflated with air or water at maximum 8 bar.
High-pressure flat lifting bag, made from coated fabric (polyester or aramid) vulcalized in one operation. Lifts up to 76 T in the standard range. Anti-slide coating
|
|
|
|
|
|
|
The Airpel Air Cylinder does away with any perceptible stiction and reduces running friction to exceedingly low levels. This gives it the unique ability to impart super smooth motion – motion smoother than any other air cylinder. Even at very low pressures. Even at very slow speeds. Even with very short strokes. Even after standing idle for years! How do you account for this remarkable performance? The Airpel incorporates a unique construction to become an instrument-quality air cylinder. It uses a precision fit graphite piston which slides freely – without lubrication – inside a Pyrex® glass cylinder. This makes it ideal for forces from a very few grams to 30 lbs. or more. In fact, Airpel is particularly well-suited to applications requiring smooth motion at ultra-low pressures – and to moving lightweight objects or delicate loads at slow or high speeds. But this air cylinder is no weakling. It can be used to provide brute forces, too – operating under extreme temperatures, at very high speeds and cycle rates, with no degradation in performance. It also runs cleaner than typical air cylinders because it contains no oil. What’s more, it has no rubber or plastic seals to abrade, wear out, or harden with time. And because all exposed surfaces (except pivot model bushings) are stainless steel and nickel, Airpel is extremely clean and corrosion resistant. Airpot Corporation is the world's leading manufacturer of ultra low friction, super-responsive pneumatic piston and cylinder motion dampers, actuators and Snubbers.
|
|
|
Good for applications where space is at a premium. No mechanical connection to the piston. Fully enclosed actuator body prevents contaminants from entering. Air or oil actuated to 100 PSIG. Operation temperature range of 0°F to 170°F.
|
|
Diaphragm Cylinders
This 1-1/4" bore diaphragm cylinder is designed for a clamping application with minimal friction losses. Its short overall height allows the cylinder to fit into a tight space with minimal friction.
Stroke length: .12".
Output force will be approximately 15% less than theoretical when units are not extended full stroke.
Cylinders should not be operated without a part being clamped (extension should be limited by customer to maximize life).
|
|
STANDARD ROLLING DIAPHRAGM AIR CYLINDERS
These cylinders provide virtually frictionless conversion of pneumatic pressure to linear force.
SMALL BORE DIAPHRAGM AIR CYLINDERS
Same friction free performance as our larger sized air cylinders.
|
|
for quick application in close space!
- Multi-layer design with Armid material.
- Fill time with 8 bar within seconds.
- Extensive accessories, like suitable case etc.
|
|
Miniature "Cube" Cylinders
CFS-01011-A is a double-acting, miniature "cube" cylinder (1/2" x 1/2" x 1/2") ideal for applications requiring low output force in extremely tight spaces.
Has been successfully applied in various semiconductor industry applications. Several are mounted side-by-side in a test fixture for circuit board continuity testing. Another application involves silicon wafer processing, in which the cylinders are used to clamp wafers during certain operations.
Stroke Length: .125".
|
|
Technical Data:
* Mini cylinders with piston diameters from 8 to 25 mm correspond
to standard ISO 6432/CETOP R 52 P
* Medium: filtered, lubricated or non lubricated compressed air
* Operating pressure: up to 10 bar
* Ambient temperature range: –20 °C to +80 °C
* Medium temperature: max. 80 °C
* Adjustable cushioning for mini cylinders with piston diameters
from 16 to 63 mm available
* Mounting nut included
* Locking units patent number 19 74 94 77
* Cylinders acceptance test conforming to ISO 10099
* Lifetime lubrication for oil-free air (Attention: Once lubricated air has
been used, then continuous lubrication will be required.)
|
|
" MINI " Series :
A little actuator able to solve big problems.The constructive principle, together with innovating materials permit to warrant higher performance such as:
- high frequencies running
- precise actuation
- constant torque all the actuation long
- high accelerations
- plenty of strokes
|
|
* Tiny - 2.00" x 1.54" x 1.50" (100 deg.)
* Many options in tiny space
* No Backlash at end of stroke
* Long Life
* "Sanitary unit" - easy to clean
Plenty of torque - 9 in. lb. @ 80 psi
Strong shaft & bearings - 40 lb. radial, 30 lb. thrust
Accessible magnetic switches for position sense
|
|
FO2, FO3, FO4
Double-acting, single end rod cylinders that multiply the force output by supplying air to multiple pistons on extension. They save space and eliminate the need for a higher pressure system. Only one piston is powered on the return stroke, saving air volume and operating costs.
Body - 304 Stainless Steel.
Heads - Anodized Aluminum Alloy.
Piston Rod - Ground and Polished 303 Stainless Steel.
Seals - Buna N (High temperature seals optional).
Rod Bushing - Oil Impregnated Bronze.
Pressure Rating - 100 PSI Maximum (Air only).
Temperature Rating - From -20°F to +150°F (-25°C to +65°C) Buna N seals with a temperature range of -20°F to +150°F (-25°C to +65°C) are standard in all Bimba air cylinders. Fluoroelastomer seals rated for higher temperature applications are available. If cylinders are operated below 0°F (18°C) for extended time periods, special modifications may be required.
Special seal materials are available upon request!
|
|
PANCAKE®-MULTI-POWER® Cylinder
The PANCAKE®-MULTI-POWER® Cylinder has multiple pistons attached to a common rod with internal air passages thus allowing much higher forces without having to use a bulky, larger bore cylinder or high pressure hydraulics.
Pancake®-Multi-Power® Cylinders come in 8 bore sizes with a choice of 2, 3 or 4 stages (pistons). Consult Catalog CV9 for available strokes.
|
|
EFP MultiPosition Cylinder
Provides three position output on extension using the same EF bore footprint to save space.
Easily interchangeable to other compact extruded cylinders of the same bore size.
Available in 10 bore sizes from 12mm to 100mm.
Versatile to easily connect and operate with application's pneumatic logic.
PTFE impregnated, hard anodized aluminum body for superior wear resistance.
|
|
Multiple Position Linear Thrusters
Bimba's Multiple Position Linear Thrusters incorporate a double-acting, single rod end cylinder that provides three positions with just one cylinder.
Bore sizes include 9/16", 3/4", 1-1/16", 2".
Multiple Position Linear Thrusters have case hardened or hard chrome plated carbon steel shafts, steel or clear anodized aluminum tooling plate and collars, and precision recirculating ball bearings or plastic composites.
Options include internal Buna N or external urethane bumpers and Buna N magnets for position sensing.
|
|
The Moveable Housing Linear Thrusters feature a compact carriage design that travels on two precision guide shafts. The mounting base ensures non-rotational linear guidance and high moment load capacity. Replaceable linear ball bearings are standard and provide long life, high load capacity and low-friction service.
Optional composite bushings and stainless steel guide shafts provide a solution for more challenging environments. A stainless steel option is offered for wash down applications. The black anodized precision machined end plates and housings are designed for replaceable stainless steel or aluminum body nose mounted cylinders. Cylinder options range from magnetic pistons to dry service. Other options include position sensing, counterbored or tapped short or long tooling plates, auxiliary mounting plates, and external bumpers or hydraulic shock absorbers.
|
|
|
|
|
|
Flat-II
Flat-II nonrotating, double-acting cylinder provides the answer to applications where rotation cannot be tolerated and space is at a minimum.
Nonrotation is achieved with dual piston rods and a rod end block that insures the rods work in tandem. Eliminates the need for external alignment devices, such as guides, rods and alignment posts or pins.
Body - 304 Stainless Steel
Heads - Anodized Aluminum Alloy
Piston Rod - Ground and Polished 303 Stainless Steel
Piston Seals - Buna N (High Temperature Seals Optional)
Rod Bushing - Oil Impregnated Bronze
Rod Seals - Buna N O-ring (High temperature seals optional)
Rod End Block - Anodized Aluminum Alloy
Pressure Rating - 200 PSI Maximum (Air only)
Temperature Rating - From -20°F to +150°F (-25°C to +65°C) Buna N seals with a temperature range of -20°F to +150°F (-25°C to +65°C) are standard in all Bimba air cylinders. Fluoroelastomer seals rated for higher temperature applications are available. If cylinders are operated below -0°F (18°C) for extended time periods, special modifications may be required.
Special seal materials are available upon request!
|
|
Non-Rotating Air Cylinders
* Bimba’s new Non-Rotating Original Line stainless steel body air cylinder design consists of a unique square piston rod with rounded corners. The square rod prevents rotation better than other rod configurations, and the rounded corners provide longer seal life than conventional hexagon rods. The unusual geometry of the square rod also provides superior rotation control.
* All bore sizes have a rotational control of less than or equal to ±3 degrees. Bore sizes for the non-rotating cylinders are 9/16", 3/4", 1-1/16", 1-1/2", 2", and 2-1/2".
* The special high strength aluminum alloy rod guide provides high load carrying capability and abrasion resistance. The urethane-based rod seal provides excellent seal life and leak-free service.
* The Non-Rotating Original Line cylinder is dimensionally interchangeable with the standard Original Line stainless steel cylinder.
* Available in Double Acting and Reverse Acting models.
|
|
|
Series OCT. Dia. 10 with 25mm. Threaded connections or Rapids prefabricated Piston octagonal = profit of push de17% and stem antirotation. Compact construction, shaped tube aluminium, 1 only type of support and detector for all the diameters.
|
|
|
|
|
|
Nonrotating, Double Acting 4 Bore sizes 3/4" thru 2" Strokes to 4" standard
Twin piston rods are incorporated into the cylinder head to achieve NON-ROTATION. The rods are securely fastened to the piston and tied together externally by a rod end tool bar.
The tool bar insures that the rods move in tandem and provides an ideal mounting surface for any attachments required by your application. The tool bar is furnished with threaded mounting holes or optional counter bored mounting holes.
Features:
4 Bore Sizes (3/4" to 2")
Strokes to 4" Standard (consult factory for longer strokes)
Self-lubricating Composite Body
Clear Anodized Aluminum Alloy Heads
Stainless Steel Tie Bolts
Bronze Rod Bushing
Prelubed with Magnalube-G® Grease
Chrome Plated Stainless Steel Piston Rods
Rod End Tool Bar
Air Service to 200 PSI
Minimum Recommended Operating Pressure - 15 psi
Temp Rating (cylinder) -25° to 225°F (-32° to 121° C)
Temp Rating (electronic sensors) -4° to 176°F (-20° to 80° C)
Internally Lubricated Buna-N Seals
Many Options Available
Magnetic Piston Sensing Available
|
|
Series OCT. Dia. 10 with 25mm. Threaded connections or Rapids prefabricated
Piston octagonal = profit of push de17% and stem antirotation.
Compact construction, shaped tube aluminum, 1 only form of mediums and detector for all the diameters.
|
|
Magnetic piston is included as standard.
Rugged body is machined from aluminum extrusion and mounts rigidly to equipment in a minimum of space.
A variety of styles are offered to meet different application requirements.
The direction of rollers are adjustable for use in different applications.
Shock absorbers are available as safety stops.
Magnetic sensors can be mounted on cylinder surfaces when input signals are required for controllers.
|
|
|
|
|
|
|
The Airpot Actuator is an instrument class pneumatic pressure or vacuum operated device designed to provide ultra-low friction and exceedingly long life with the least amount of mass and contamination. It is particularly well suited for applications requiring the most sensitive response possible from an air cylinder. Airpot Corp. manufactures two basic families of pneumatic actuators. Both employ our unique combination of a Pyrex® glass cylinder and graphite piston and have similar performance properties with respect to friction, cleanliness, and temperature range. The major differences are in the actuation direction capabilities, outer construction, mounting features, and dimensions. The performance properties of either product are vastly superior to those of conventional cylinders. Airpot Corporation is the world's leading manufacturer of ultra low friction, super-responsive pneumatic piston and cylinder motion dampers, actuators and Snubbers. Our unique seal-less construction and combination of materials allow unsurpassed longevity, high cycle rates without lubricants, smooth operation at extreme temperatures, and instrument quality performance for low to medium force and energy levels. Common applications for our Actuators, Piston and Cylinder Motion Dampers, and Snubbers include: semiconductor & IC processing equipment, web/wire/filament tension controls, test & measurement instruments, automated medical analyzers, dispensing & vending machines, high capacity mail & cash handling equipment. Complete line includes instrument quality, precision air dashpots, snubbers, pneumatic actuators, Airpel Anti-Stiction Air Cylinders and Airpel-AB cylinders.
|
|
PneuMoment Pneumatic Actuators
The Bimba PneuMoment pneumatic actuator features a revolutionary, compact design that uses conventional pneumatic technology but has the capacity to carry high loads and moments.
The Bimba PneuMoment pneumatic actuator carries high moment loads and has a compact design. It also uses non-lube bearings, has a built-in track for position sensing switches, and guide beam end cap ports transmit air or vacuum through the actuator from the guide beam end cap to connect additional automation devices such as grippers.
The actuators also have internal or external bumpers, external shock absorbers for retract and extend strokes, internal stroke adjustment - full stroke, retract and extend (1-1/16" and 2" bores only), and magnetic position sensing.
Bore sizes are 1-1/16", 27mm, 1-1/2", 38mm, 2", 50mm, 2-1/2", and 63mm. Standard stroke lengths range from 1" increments to 6" and 25mm increments to 150mm.
|
|
|
Modular concept of assembly of elements of automation without interfaces (direct assembly) 208 combinations. Possible indirect assembly: plan, interface and provided screws and bolts. Reduction of study and maintenance. Effective, simple, economic.
|
|
|
MSC, ZSC and MSN elements of the Easy-2-Combine.Dia range. 6 with 25mm, standard races 10 with 200mm. Ideal solution for the projects of automation and assembly. Optimization of the guidance and the sweeping force. Easy maintenance.
|
|
|
Camozzi offers a wide range of cylinders with diameters from 6 to 200 mm and with strokes from 5 to 3000 mm, single-acting or double-acting, with or without through rod, magnetic or non-magnetic, with external guidings available on some models. The cylinders can be used in numerous applications, such as assembly lines, packaging and production machinery, at high temperatures and in extremely corrosive environments. The large and versatile range of Camozzi’s cylinders allows the user a greater degree of flexibility in devising technical solutions, by offering numerous mounting options, high speed rates and ensuring the use of high quality raw materials in its components. A large selection of cylinder accessories is available to complete the range.
|
|
|
AGI's pneumatic actuator, powered feed-escapement is ideal for individual release of parts from hoppers, conveyors, vibratory feeder bowls, tracks and magazines. These compact long stroke Linear actuators escapements are internally sequenced. The cross porting makes sure both rods are extended before either rod can retract ensuring positive part feeding. The AGI escapements have an easy part clearing feature due to internal back pressure cross port design, allows both rods to be retracted with air pressure off.
|
|
Spring return or double acting, anodized aluminum, quarter turn, rack and pinion actuator.
|
|
ACT-1
Pneumatic Actuators (Air Cylinders)
with Embedded Feedback Sensors
Enfield Technologies pneumatic actuators contain linear resistive transducers for continuous analog absolute position feedback.
Features:
* Analog LRT sensor
* Embedded design is compact and provides protection to the sensor
* Standard M8 3-pin sensor connector
* Multiple bore (diameter) and stroke (length) sizes available
* Compatable with Enfield Technologies controllers as well as components from many other vendors
* Independent Input Signal Scaling
|
|
Pneumatic actuator Positioner 0,2-1 bar (AP)
In option:
Version ATEX category 1 (zone 0) with detectors of ends of the road and reader of angle
or ATEX category 2 (zone 1) with detectors of ends of the road and converter 4-20 my
Assembly:
- Direct Assembly on the actuators models 05 to 14.
The unit obtained comprises neither pipe, neither external electric wire nor mechanical drive: ideal for a precise positioning and without play.
- Universal Version with adaptation for actuators models 16 - 18 and 20
- Universal Version with male exit square (standard Kinetrol) or interfaces VDI/VDE 3845 Namur for assembly with adaptation on any other actuator or any other application ¼ turn.
Identification:
- Symmetrical parallelepipedic Form
- Entered of pilot air and driving air on the same frontage
|
|
|
|
Pneumatic cylinders
