|
|
| Products 91 to 120 of 196 |
2A Cylinders Parker's 2A series pneumatic tie rod cylinders are heavy duty, steel-bodied cylinders designed for applications where a conventional aluminium-bodied pneumatic cylinder would be vulnerable to external physical damage. Typical applications include steel mills, aluminium smelters and foundries.
2A cylinders are designed to NFPA and ANSI specifications.
Standard pressure: up to 18 bar (250psi)
Bore sizes: 25.4mm to 355.6mm (1" to 14")
Choice of rod diameters and rod end threads
15 standard mounting styles
Any practical stroke length
Standard temperature range: -20°C to 80°C
Suitable for filtered & lubricated air - also available for non-lubricated air
Options include cushions, stroke adjusters, rod bellows and wipers, proximity sensors etc.
Special designs to customer specification. |
|
| The Airpel Air Cylinder does away with any perceptible stiction. And reduces running friction to exceedingly low levels. This gives it the unique ability to impart super smooth motion – motion smoother than any other air cylinder. Even at very low pressures. Even at very slow speeds. Even with very short strokes. Even after standing idle for years! How do you account for this remarkable performance? The Airpel incorporates a unique construction to become an instrument-quality air cylinder. It uses a precision fit graphite piston which slides freely – without lubrication – inside a Pyrex® glass cylinder. This makes it ideal for forces from a very few grams to 30 lbs. or more. In fact, Airpel is particularly well-suited to applications requiring smooth motion at ultra-low pressures – and to moving lightweight objects or delicate loads at slow or high speeds. But this air cylinder is no weakling. It can be used to provide brute forces, too – operating under extreme temperatures, at very high speeds and cycle rates, with no degradation in performance. It also runs cleaner than typical air cylinders because it contains no oil. What’s more, it has no rubber or plastic seals to abrade, wear out, or harden with time. And because all exposed surfaces (except pivot model bushings) are stainless steel and nickel, Airpel is extremely clean and corrosion resistant. |
|
ISO/VDMA Series Metric Standard Interchangeable Cylinder
The ISO/VDMA Series is an aluminum body air cylinder line that is designed to meet all your international cylinder requirements. In fact, our ISO/VDMA Series cylinders are designed to meet the requirements of ISO 6431 (International) and VDMA 24562 (Germany). The combination of lightweight aluminum construction and proven reliability makes our ISO/VDMA Series the Superior Interchangeable metric, international standard air cylinder line.
GeoMetric® ISO/VDMA Cylinder
The GeoMetric® Series conforms to the following cylinder specifications: VDMA 24562, DIN/ISO 6431, and ISO/FDIS 15552. One of the most desirable features of the cylinder line is the dual switch/sensor groove design that is a standard offering on all GeoMetric®cylinders. The dual groove design offers great flexibility when mounting switches and sensors to the cylinders. One groove is a traditional round groove and the other is what we call the CombiGroove®. The CombiGroove® is a unique design that will accept round and angular switches/sensors. |
|
| Conforming to ISO 6431, VDMA 24562 and NFE 49-003-1 standards. Seven ranges including SMART cylinder with stainless steel versions for all requirements. Double and single acting models with bore sizes from 32-200mm. Comprehensive choice of mountings. |
|
| Double and single acting cylinders with magnetic pistons. Featuring an attractive square style profile barrel with concealed tie rods and integrated grooves for flush mounting off magnetic sensors. Low friction long life seals. |
|
Series CV
New Generation Series CV Cylinder design enhancements include increased width of PTFE wear ring for greater support, durability, and increased piston seal retention for higher speed applications. A new imperial design of the Series CV Cylinder is available with imperial ports, stroke length, and rod for easy integration in imperial facilities. A rod seal retention ring has been added to improve performance in extreme applications. Units affected by these enhancements include Series SK/SL, SG and SCV Slides.
Standard features of the Series CV Cylinders include rugged and lightweight anodized aluminum alloy heads, caps, and tubes. Port Controls® regulate speed through the entire stroke. Standard alloy steel and optional corrosion resistant stainless steel piston rods are hard chrome plated for maximum life and durability. Female threads and a variety of mounting accessories provide ease of integration.
Advantages: Anodized aluminum alloy heads, caps and tubes, durable, robust, longer life, drop-in replacement. |
|
Air Cylinders with Adjustable Cushions
The Bimba Air Cylinders with adjustable cushions have a readily accessible cushion needle for easy adjustment, double acting models, and a 304 stainless steel body with mirror finish I.D.
High strength aluminum alloy porting ends and ground and roller burnished 303 stainless steel piston rods come standard. Also, the air cylinders have Buna N "U" Cup Seals, low breakaway friction - less than 5 PSI - and special stroke lengths available on request.
Air cylinders come in 3/4", 1-1/16", 1-1/2", 2", 2-1/2", and 3" bore sizes.
Bimba's cylinders with air cushions provide a possible solution to destructive energies. The air cushion traps a small amount of exhaust air at the end of stroke, providing an air pocket that decelerates the load. This reduces the potentially destructive energy being transmitted to the cylinder and other components. |
|
Extruded Flat Lift Table
EF1-based, guided cylinder with four shafts for maximum rigidity. It is designed for lifting applications where other non-rotating cylinders cannot handle an overhung load and space is at a premium.
Four-shaft support withstands offset loads and moments.
Simple, efficient design provides economical alternative to other costly guided actuators.
Joins the EF family of products, so shares all the same benefits--long service life, low friction operation, fast delivery.
Convenient wide tooling mounting surface.
Intended for vertical lifting applications (should not be mounted horizontally or with tooling plates facing down). |
|
GeoSlide Series Guide Unit
The GeoSlide guide units utilizes Numatics GeoMetric ISO 6431 VDMA cylinders. The FHG & FHK series offers high load carrying capabilities in a metric package.
Features:
Bore sizes range from 32mm to 100mm.
Strokes up to 500mm.
Linear ball or bronze bushings option.
Available in a "U" style body.
LCX Series Linear Slide
The LCX Series linear slide combines cost-effectiveness with proven dependability. An economical alternative with greater load carrying capabilities.
Features:
Low Cost
High Load Capability
Stainless Steel Shafts Available
Engineered Plastic Polymer Bearing
Available in 3 Bore Sizes |
|
Z Line Air Cylinders
The Bimba Z Line Air Cylinders are for extremely tough applications.
The Z-Line air cylinder has the rolled-in construction of the Original Line but features the following: Larger diameter, two-piece 303 stainless steel piston rod HEX-STUD rod end thread of heat treated alloy steel - easily removed in case of failure due to overload, and cushion quiet elastomer bumpers.
No charge options include the Magnalube G, Molycoated body, and magnet.
Bore sizes for the Z Line cylinders are 3/4", 1-1/16", 1-1/2", and 2". |
|
Inflated with air or a fluid (water, oil, glycol...) depending on the application, PRONAL flexible lifting bags are pneumatic components which perform mechanical functions such as pushing, squeezing, guiding, clamping, blocking, damping, lifting, moving...
They are easy to incorporate within mechanical systems and are used in presses, moulds, conveyors, handling robots, lifting tables...
Advantages :
- thin when empty,
- compact,
- uniform lifting power
- very easy to adapt,
- high lifting force.
A highly diversified range of products
- standard square shape (100 to 1,000 mm in length), single or multi-stage, inflation pressure up to 7 bar (12 models),
- customized rectangular or curved shape, all sizes,
- multiple accessories which can be adapted to the environment.
Made from elastomer-coated fabrics, flexible lifting bags are vacuum vulcanised at a temperature of 140°C. |
|
Hole Punch Cylinders
Designed to punch millions of holes in plastic or other thin sheet materials 2 to 3 mils thick, the long-life BIMBA Pneumatic Hole Puncher will give you more cycles per penny.
The hardened steel cutter with ground razor sharp edges is an integral part of the cylinder. A small air jet ejects the slugs from the cutter preventing slug build up, and Elastomer Bumpers insure cushion quiet operation.
Less than 1" in diameter, several cylinders can be closely mounted. Available in seven hole cutter sizes from 1 / 4 " to 5 / 8".
This stainless steel body, single acting spring return cylinder has a 3 / 4" bore and 1" stroke. A nickel plated steel rod guide is threaded for easy nose mounting, and a 1 / 8" NPT air inlet is conveniently located in the rear head.
Prelubricated with HT-99, the cylinder can be operated with ordinary shop air at pressures up to 250 psi. |
|
Narrow Profile Air Table Actuators
The NPA actuator provides precise load guiding with a recirculating ball rail above its bore.
Two bearing styles are offered (single/double bearing block) to accommodate both lower cost and higher precision/cost applications.
With standard strokes up to 120mm, the NPA offers longer travel length than any competitive actuator of its type.
Bore sizes: 12, 20, 32mm. |
|
Diameters 8, 12, 18, 25, 32, 40 mm
Stroke length 1 ... 5,000 mm
Force 30... 754 N
Position sensing
Various cushioning options available
Guide variants
- Basic guide
- Plain bearing guide
- Ball bearing guide.
|
|
Diameters 18, 25, 32, 40, 50, 63, 80 mm
Stroke length 10 ... 3,000 mm
Force 153... 3,016 N
Position sensing
Adjustable cushioning
Guide variants
- Basic guide
- Plain bearing guide
- Ball bearing guide
- Heavy-duty guide.
|
|
High rigidity and flexible fitting by highst precision in manufacturing. Flexibly expanding intermediate positions increase the possibility of applications.
|
|
Two Axes of Motion in One Housing!
Rigid Design Holds Guide Shafts at Both Ends
Deflection Under Heavy Loads is Greatly Reduced
Air Cushions Standard on 1" & 1.5" Bore Sizes
Precision Mounting Surfaces with Tooling Holes for Grippers and Tooling. Custom Faceplates are Available
Heavy Wall Cylinders Built Into Housing
Case Hardened Shafting
Composite Bushings or High Precision Linear Ball Bearings Provide Accurate and Repeatable Motion
Floating Couplers
Pre-Mounted Cable Carriers
Adjustable Shock Absorbers
Optional Threaded Stop Collars for Fine Stroke Adjustment
Dovetail Sensors with Optional "Quick Disconnect" |
|
Linear Thrusters Pneu-Moment
For smooth, guided motion. A durable housing with guide shafts keeps our Linear Thruster from rotating and allows it to carry higher loads. Choose from two different models. A choice of stroke lengths and a wide variety of catalog options make the Bimba Linear Thrusters easy to use and ready to order.
The Benefits of the Linear Thrusters Pneu-Moment Include:
Bimba stainless steel body air cylinders for long, reliable life
Optional magnetic piston for use with Hall Effect or Magnetic Reed Switches
Optional adjustable cushions for smooth deceleration of load at end of stroke
Optional internal or external bumpers to absorb shock or adjust stroke
Easily accessible ports |
|
| High load weight vs extension. Five bore sizes from 3/4" (20mm) to 2" (50mm). Stroke lengths up to 12" (305mm), Base or side mount. Linear ball or composite bearings. Options include switches, shock absorbers, stop collars and bumpers. |
|
Linear ball bushings or PHDs TC fluoropolymer composite bushings are available in each series providing the best value with the least possible slide deflection. Four bushings allow two hardened precision ground shafts to move smoothly while supporting the tool plate and attached loads, providing rugged precise linear motion. .
Advantages: Wide variety of travels and sizes, oversize shafts with PHD's rugged TC bushings provide excellent value |
|
Pneu-Turn Actuators
The Bimba Pneu-Turn Actuators have cylinder bodies with 304 stainless steel for maximum seal life and an actuator body that's high strength, anodized aluminum alloy for maximum corrosion protection. The porting ends are high strength, anodized aluminum alloy.
The shaft bearings are self-lubricating, sintered iron copper material for lower friction and the piston seals run with Buna "N", U-cup type for low breakaway friction and long life.
Angle adjustment is an option that allows 45° of adjustability at each end and the adjustable cushions are an option that controls deceleration at the end of the rotation.
Torque factors include 9/16" bore, single rack; 9/16" bore, double rack; 3/4" bore, single rack; 3/4" bore, double rack; 1-1/16" bore, single rack; 1-1/16" bore, double rack; 1-1/2" bore, single rack; 1-1/2" bore, double rack; 2" bore, single rack; and 2" bore, double rack. The Pneu-Turn angles of rotation are 45°, 90°, 180°, 270°, and 360°. |
|
Size 6, 8, 10, 12, 16, 25, 32, 40 mm
Torque 0.15 ... 20 Nm
Swivel angle 0 ... 270°
Position sensing
Fixed cushioning.
|
|
Features
● Rotary cylinder with double rack and pinion
● High precision positioning
● Shock absorber is mountable
● Intergrated table and pinion (Rigidity)
● Various applications through round table
● Easy wire arrangement by hollow axis
● Auto switch is mountable |
|
Pneumatic positioner for propotional acting :
The device positioner is particularly suitable to govern rotary actuators; used on butterfly or ball valves. |
|
| AGI offers a full line of pneumatic rotary actuators. All rotary actuators are rack and pinion design and incorporate output flange hard stop. The hardstops stops the output flange directly so there isn't any pinion breakage. The units are ultra hi torque pneumatic actuators due to cross porting the two piston bores. The extremely low profile package is excellent in tight space applications. There are five sizes available with manifold and mid stop options. Torque output ranges from 7in-lbs. to 310 in-lbs. @ 100 psi. |
|
Rotary Vane Pneumatic Actuators
Features
·Torque output of 16 to 1000 Inch Pounds
· Adjustable Rotations
· Reed and Hall effect switches
· Only one moving part
· Non Lube service
· Low cost solution
·Heavy Duty Double Acting Ball Valve Systems
Valve sizes from ¼” to 3”
140 in.lbs to 800 in.lbs
· Spring Return Valve operators
Single acting with spring close or open
Valve Operator Systems
·
·Spring Return operators are formed by bolting a spring return unit to a double acting Val-U-Act operator. The return movement is effected by a clock-type spring which is pretensioned to about half the operator torque. The amount of pretention is large, compared to the rotation and therefore the torque does not vary more than 20% over the rotation.
Spring returns are factory-installed and adjusted. The spring returns have a worm drive adjustment for setting or changing spring pretension. By inserting a socket key into one end of the worm the spring pretension can be very easily increased or decreased to suit operating conditions. To increase pretension, turn the worm clockwise; to decrease, turn counterclockwise. |
|
RR-Heavy Duty - Flange Output Rotary Actuator
This heavy-duty rotary actuator is ideal for payloads up to 200 lbs [91Kg] in weight. They are available in standard 45, 90, 135 or 180 degrees of rotation. Optional shocks/stops, mid-stop and rotary manifold available.
1. Low profile and bearing supported turn table provides an extremely compact package for tight space applications
2. Payload can be connected directly to the turn table. Eliminates the need for a bearing block
3. Zero backlash, preloaded ball bearings, and slip fit dowel pins make this a very precise and repeatable rotary actuator
4. Air manifold option eliminates twisted airlines |
|
Globe Motors designs and manufactures precision rotary actuators to meet your specific MIL-spec or industrial requirements. All actuators offered are powered by Globe Motors, long-recognized for performance quality. The rotary actuators listed here are intended only to provide a sampling of the wide range of units that have been designed and manufactured by Globe Motors.
Our experienced design and application engineers stand ready to assist you with motion control solutions; and our vertically integrated manufacturing provides the capability needed to deliver prototypes quickly.
|
|
|
|
Pneumatic cylinders
