Torsionnaly-rigid flexible couplings

Type HRC flexible couplings are among the most robust available. They are chosen for the most common applications. Their machined diameter makes alignment quick and easy: just use a ruler to install them. HRC couplings are highly heat-resistant. Two ...

Torque: 10 Nm - 975 Nm

These elastomer star couplings are used on servo shafts to overcome critical vibrations and when all-steel couplings reach their limits. They transmit torque without backlash and compensate for misalignment. ACPG couplings now combine ...

Torque: 11.5 Nm - 420 Nm

Curved-tooth couplings function as flexible connections. They are particularly suitable for transmitting high torques. They compensate for axial, radial and angular misalignments of the shafts to be connected. Gear couplings can be mounted ...

Torque: 1.1 Nm - 35 Nm

High-Gain Rubber Type Coupling XG 1. Reduction of Stabilization Time The improved limit gain of servomotors can reduce stabilization time. 2. Speed Unevenness Suppression Speed and torque unevenness arising from misalignment will ...

Torque: 0.6 Nm - 200 Nm
Rotational speed: 6,000 rpm - 42,000 rpm

XHW series is disk type flexible coupling. High-torque specification with rated torque 1.5 times higher than conventional products. This is the most appropriate for a servomotor with instantaneous max. torque of 350%. The stainless ...

Torque: 1.5, 3.3, 6.3, 12 Nm
Rotational speed: 12,000, 15,000, 17,000, 23,000 rad.min-1

Flexible couplings with vibration absorption function added to high rigidity couplings. A structure with both high rigidity and vibration absorption. The individual dynamic vibration absorber is separate from the inertial rotor and ...

• Double cardanic curved tooth gear coupling • Application in mechanical engineering and hydraulics • Compensation of misalignment of shaft axialradial-angular • Axially pluggable - simple mounting • Hub material: steel • Sleeve ...

• Torsionally rigid, positive coupling for diesel engine drives of hydraulic pumps • Short installation lengths • Simple plug-in installation of hub and fl ange without aligning tools • Maintenance free due to combination of materials ...

Torque: 0.05 Nm - 10 Nm
Rotational speed: 0 rpm - 15,000 rpm

Miniature Metal Bellows Coupling with set screws  • Backlash-free miniature metal bellows coupling with radial set screws  • For shaft diameters from 1 – 24 mm  • High torsional stiffness, compensation of shaft misalignment ...

Torque: 0.1 Nm - 10 Nm
Rotational speed: 0 rpm - 15,000 rpm

Miniature Metal Bellows Coupling with collet clamps  • Backlash-free miniature metal bellows coupling with clamp hubs • For shaft diameters from 1 – 25mm • High torsional stiffness, compensation of shaft misalignment at ...

Torque: 18 Nm - 1,400 Nm

Metal Bellows Coupling with collet clamps  • Backlash-free metal bellows coupling with clamp hubs  • Hub material: up to 60Nm – aluminum, up from 80Nm - steel  • For shaft diameters from 10 – 80 mm  • High torsional ...

Torque: 0 Nm - 5 Nm
Rotational speed: 0 rpm - 8,000 rpm

Corrosion proof HKD metal multiple disc couplings compensate a parallel misalignment up to ±0.5 mm and an axial misalignment up to ±1.5 mm as well as extending the service life of encoders in the process. The double joint couplings are ...

Torque: 5 Nm
Rotational speed: 10,000 rpm

The corrosion-resistant HK metal multiple disc couplings compensate for an angular misalignment of up to 0.5° and an axial misalignment of up to ±1 mm, thus extending the service life of encoders. The single-jointed couplings are available ...

Torque: 100 Nm
Rotational speed: 12,000 rpm

The isolated and corrosion-resistant HKI 97 metal multiple disc couplings compensate for increased parallel misalignment up to ±1 mm and increased axial misalignment up to ±2 mm, thus extending the service life of tacho generators. The ...

Torque: 200 Nm - 130,000 Nm
Rotational speed: 2,000 rpm - 11,500 rpm

Disc Couplings are steel construction with stainless steel disc packs, backlash and maintenance free, require no lubrication and are free from wear. Can be mounted Shrink Discs for optimal performance. All steel made Superior disc pack ...

Torque: 40 Nm - 3,600 Nm
Rotational speed: 2,400 rpm - 6,000 rpm

one elastic element made of pre compressed natural rubber reinforced with steel, to be fitted with fixing screws and with a metallic band (to be removed after mounting); • two metallic hubs made of forged steel (size 120 produced in cast ...

Torque: 30 Nm - 7,500 Nm
Rotational speed: 2,100 rpm - 14,000 rpm

Hubs in steel or Nylon 6.6 Sleeve in stabilized 6.6 super polyamide resin Couplings can be supplied according to ATEX DIRECTIVE 94/9/CE. "Equipment and protective systems, which may be used in areas endangered by potentially explosive atmospheres".

Torque: 30, 45, 80 Nm
Rotational speed: 12,000, 10,000, 8,000 rpm

Aluminum Oldham shaft coupling - GMT - bore diameter D1 = 14mm / D2 = 14mm Oldham coupling with black polyacetel(POM) Spacer - Set screw Operating temperature: -20°~80°. Offset of angular, parallel, or axial deviation are individual ...

Torque: 3 Nm - 50 Nm
Rotational speed: 8,000, 7,000, 6,000, 5,000, 4,000 rpm

Oldham coupling with aluminum bronze spacer - Set screw Offset of angular, parallel, or axial deviation are individual allowed value, so couple reasons of axial offset appearing at same time would reduce the unit allowable value. Suit ...

Torque: 15 Nm - 10,000 Nm
Rotational speed: 0 rpm - 10,000 rpm

Metal bellows coupling with simple flange mounting Features For simple flange mounting to special drive components Custom flange patterns available Temperature range -30 °C to +100 °C (-22 °F to +212 °F) Design Two mounting flanges ...

Torque: 15 Nm - 10,000 Nm
Rotational speed: 0 rpm - 10,000 rpm

Bellows coupling with clamping hub Features Easy to mount Optional: bolt tensioning system in size 800 and up Light weight and low moment of inertia Temperature range -30 °C to +100 °C (-22 °F to +212 °F) Design Two clamping ...

Torque: 15 Nm - 4,000 Nm
Rotational speed: 0 rpm - 10,000 rpm

Bellows coupling with split clamping hub Features Radial mounting possible Easy installation onto pre-aligned shafts low moment of inertia Temperature range -30 °C to +100 °C (-22 °F to +212 °F) Design Two fully split clamping ...

Torque: 20.33 Nm - 232.48 Nm
Rotational speed: 4,100 rpm - 12,000 rpm

Steel Double Flex CD® Flexible Shaft Couplings provide a tough, robust, and durable design that is ideal for motion control applications requiring increased misalignment capacity compared to Zero Max’s Single Flex design . The Double ...

Torque: 30.5 Nm - 2,327.48 Nm
Rotational speed: 500 rpm - 2,250 rpm

Clamp-Style Hubs featuring floating shaft CD couplings is a zero backlash and torsionally stiff spacer coupling that provides superior misalignment capacity for applications where the drive and load components require further spacing ...

Torque: 30.5 Nm - 2,327.48 Nm

Setscrew Hub CD Floating Shaft Couplings are ideal for applications where the drive and load components require further spacing from each other. This unique design is torsionally stiff and delivers zero-backlash, superior misalignment ...

BRAKE DRUM COUPLING TYPE RKK-WBT About the product Elastic shaft coupling, Claw coupling with brake drum for drum brakes according to DIN 15435 Coupling is positively and breakdown-resistant Made from solid material (C45), no casting ...

BRAKE DISC COUPLING TYPE RKK-WBS About the product Elastic shaft coupling, Claw coupling with brake disc for disc brakes Coupling is positively and breakdown-resistant Made from solid material (C45), no casting design 2-Components ...

ELASTIC SHAFT-, CLAW COUPLING TYPE RKK-W About the product Elastic shaft coupling, Claw coupling with brake drum for drum brakes according to DIN 15435 Coupling is positively and breakdown-resistant Made from solid material (C45), ...

Torque: 285 Nm - 20,787 Nm
Rotational speed: 2,200 rpm - 6,000 rpm

• High transmittable torque ratings • Vari-crown tooth form for improved torque transmission and longer life • Strong compact design • Low inertia and high maximum speeds • Spacer couplings available on request • Full-Flex and Flex-Rigid ...

Torque: 859 Nm - 24,917 Nm
Rotational speed: 3,000 rpm - 6,000 rpm

• High transmittable torque ratings • Vari-crown tooth form for improved torque transmission and longer life • Strong compact design • Low inertia and high maximum speeds • Spacer couplings available on request • Full-Flex and Flex-Rigid ...

Torque: 0.1129 Nm - 53.1 Nm

Disc type magnetic couplings consist of two opposing discs with powerful rare earth magnets. The torque applied to one disc is transferred through an air gap to the other disc. Because of its simple flat design, you can have angular misalignment ...

Torque: 15 Nm - 10,000 Nm

Metal bellows coupling with simple flange mounting Features For simple flange mounting to special drive components Custom flange patterns available Temperature range -30 °C to +100 °C (-22 °F to +212 °F) Design Two mounting flanges ...

Torque: 15 Nm - 10,000 Nm

Bellows coupling with clamping hub Features Easy to mount Optional: bolt tensioning system in size 800 and up Light weight and low moment of inertia Temperature range -30 °C to +100 °C (-22 °F to +212 °F) Design Two clamping ...

Torque: 15 Nm - 4,000 Nm

Bellows coupling with split clamping hub Features Radial mounting possible Easy installation onto pre-aligned shafts low moment of inertia Temperature range -30 °C to +100 °C (-22 °F to +212 °F) Design Two fully split clamping ...

Rotational speed: 310 rad.min-1 - 14,500 rad.min-1

The coupling is the insurance of the system. But main function of İt İS, two connect two shafts to transmit the movement and the power. İt would be produced from different material gualities and different types. GEKU produces 28 different ...

Torque: 0 Nm - 1,000,000 Nm

Gear Couplings Standard Range AGMA Type Axial Travel Type Continuous Sleeve Type Flanged Sleeve Type Stainless Steel Standard Range NDE Clarke Pitchline has manufactured it’s own standard series of Couplings for over 40 years. ...

Disconnect Type We can offer a number of different styles of Disconnect Type Gear Coupling which can be custom designed to suit the customers application. The specially designed gear coupling enables our customers to quickly and easily ...

Spacer type Using our standard range of High Power Gear Couplings, we can offer a wide range of spacer type gear coupling with varying lengths and Diameters. Units can be balanced for high-speed applications. These spacer type gear ...