|
|
The unique SLB 125 three-in-one busbar tool guarantees effortless cutting,
bending and punching of aluminium and copper busbars. Whether in the work shop
or at the construction site - the basic unit transformes into a cutting,
bending- or punching machine within seconds. Busbar fabrication from a single
mould:
Precise, simple and quick.
Advantages:
• Especially robust and stiff frame.
• Very high quality cutting, bending and punching.
• High operating safety with the built-in safety system.
• Lightning-swift tool changes with a minimum of
manipulation.
• The 150 bar low-pressure system ensures a long
service life and very fast cycle times.
• Punches copper and aluminium busbars up to
13 mm thick, elongated holes up to 21 x 14 mm
and round holes up to 21 mm in diameter.
• Busbars bent accurately up to 120° - very accurate
reproducibility of the set angle.
|
|
|
|
|
|
Mechanical, thermal and chemical wire stripping processes cause damage to underlying wire that can affect electrical component performance and cause unacceptable conductor failures for aerospace, defense, medical, automotive, and other industrial companies using mission critical electronics. Manufacturers of these devices need to be aware that laser wire stripping technology is available that will guarantee the elimination of these problems. Applying CO2 laser light (10.6 microns wavelength) vaporizes wire insulation while being incapable of affecting the conductive wires. This wavelength of laser light is absorbed by the wire insulation and completely reflected by metal wire conductors. This technology eliminates the need for replacement blades and hazardous chemicals. Using lasers to strip wire yields the highest quality insulation and adhesive removal while delivering the absolute best quality and most precise wire stripping available.
Lasers can remove wire insulation from a wide variety of wire types including single core, multiple leads, twisted pairs, multi-cable, coaxial cable, and many others. Wires with diameters as low as 0.001 inches can be safely stripped. Tolerances for the laser can be held as tight as 0.001 inches. Single strand wires can be stripped in less than 1 second.
Virtually all wire insulation types can be removed using this laser technology. Wires are easily slit using this same CO2 laser. Straight, T-strip, Window slits, as well as, Spiral strips can be programmed to a controlled depth.
Our non-contact process yields the most flexible, highest quality, and most reliable laser stripping and slitting available.
|
|
General features
- Mark, strip and cut multiple gauge wire/cable in a fully automatic, high speed, computer controlled operation.
- Permanent, high contrast surface marks without damage on all insulations specified in SAE Aerospace Standards.
- Mark without masks...virtually any character, any font, any symbol.
- Strip with zero defects/damage to the wire core.
- Industry standard wire transport.
- Compliant with SAE Aerospace Standards.
|
|
MOVABLE CABLE STRIPPER
-motive power : 3 hp (1 or 3 phase)
- Voltage : 220 v / 340v
- electric power : 2.2 kw
- Product Hight : 1200 mm
- Product Width : 580 mm
- Product Length : 900 mm
- Product Weight : 450 kg
Applying three different types of mechanism, the machine can strip exterior covering and interior covering of wire in accordance with the shape and size of scrap wire or defective wire.
For more detail, the machine is equipped with two parts being put together to make the stripping process to be effective: thickness selective stripping part and thickness adjustable stripping part. The thickness selective stripping part can cut and strip the interior covering of wire by selecting the thickness of interior wiring inserted into wire with the upper pressure roller of exterior covering cutting part repeatedly opening and closing. The thickness adjustable stripping part can strip the interior wiring by adjusting the cut depth according to the thickness of interior wiring.
|
|
CABLE & WIRE HYDRAULIC CUTTER
- motive powe) : 2 hp (1 or 3 Phases)
- Voltage : 220 v / 340 v
- Electric power : 1.5 kw
- Pressure of oil pressure pump : 240BAR
- Instantaneous pressure : 260BAR
- Capacity : ALP 1 AB-3(2CC)
|
|
|
|
|
|
PowerStrip 9500 automatic cutting and stripping machine for processing wires up to 12 mm (0.47'') in diameter with pull-off lenghts up to 200 mm (7.87'') on the right wire end (leading end) and 100 mm (3.94'') on the left end (trailing end).
Various models of the PowerStrip 9500 are available - from automatic processing of coaxial cables / shielded cables with rotary incision unit, to special Kevlar cutting head or integrated saw (e.g. for succoform or POF cables). Wire sizes from 0.03 to 25 mm² (AWG 32 - 4) can easily be cut, stripped and slit with unmatched precise Schleuniger stripping quality and high processing speed.
A multiple-blade system on the cutter head allows to use of up to 3 pairs of blades which can easily handle most cutting, stripping and slitting requirements.
The PowerStrip 9500 and all other Schleuniger automatic cut & strip machines can be integrated with various pre- and post processing equipment for prefeeding, marking / inkjet printing, coiling and stacking in an automatic production line. Programming can be either done directly on the PowerStrip 9500 itself or with the PC software Cayman with an easy-to-use graphical editor (WYSIWYG).
|
|
SELF - LIFFTING STANDS
Unwinding stands for sites - carr. capacity 1500 to 5000 kg.dia. Ø600-2800mm
|
|
Insulated Stripping plier low voltage
PBT12 16 for cables diameter 10 to 40 mm
PBT20 20 for cables diameter 21 to 52 mm
We also sell stripping tools for medium voltage cables:
Complete set of tools for cable processing, section from 35 to 630 mm²: including tools to strip external sheath, cable insulation, semi conductor. To realize chamfer, cones and slots
|
|
Weidmüller Stripax® and stripax® 16 are stripping and cutting tools for flexible, stranded and solid conductors with PVC insulation.
suitable for cross-sections 0.08 up to 6 mm² (~AWG 28... 10), respectively 6 up to 16 mm² (~AWG 10... 6)
Stripping length adjustable by setting wire stop
Jaws open automatically after stripping
No splaying of individual strands
Special self-adjusting stripping blades avoid damage of the conductor
Adjustable to different insulation cross-sections
Stripax®: Strips multiple conductors, even several flat ribbon conductors simultaneously
Strips double-insulated conductors in two steps, no additional adjustment necessary
Stripax® 16: Cuts flexible, stranded and solid conductors for cross-sections up to 16 mm²
Precise, self-adjusting cable-cutter
Long working life
Improved ergonomic design
|
|
|
|
|
|
Schleuniger UniStrip machines have been proven thousands of times to process wires, cables and a wide variety of special cables. They all operate with extremely fast cycle times and feature a universal blade system that eliminates time consuming change-overs.
Depending on the model, UniStrip machines process wires and cables from 3.2 mm (0.12'') outer diameter up to 9 mm (0.35''). For flat cable processing with the fully programmable UniStrip 2600 or UniStrip 2700 the maximum material width is 11 mm (0.43''), respectively 63 mm (2.48'').
The most flexible machine, the UniStrip 2600 can process many unique applications and wire / cable types, including discrete wire from 0.03 mm2 up to 16 mm2 (AWG 32 - 6), power cords (even multiple conductors with different lengths; all steps processed in one cycle), multi-conductor cables, flat cables and more. Programming the UniStrip 2600 is simple with its cable library (programmable in mm2 and AWG), proven menu-guided software and a graphical user interface.
|
|
|
Units for removing the cable isolation or for removing coatings and lengh measuring devices.
|
|
Characteristics of CNC pipe bender:
-Multi-servo axis numerical controlled.
-Input data of Y. B. C or according to Descartes X. Y. Z. coordinate can build bending parameter. According to the input data or built parameter the profile of tube will show on the computer.
-Automatic bending rebound numerical compensation according to accurate measured data. Modify the bending rebound compensation data or compensate manually If the bend is different with what you expect.
-Storage capability: 100 bends for each workpiece. 1000 workpieces'data could be memorized.
-Adopt WINDOWS XP Embed operation system.
-Program transmit: (1) Flash Disc (2) Internet (3) Floppy Disc.
-The heavy-duty series CNC pipe bender(Max.Φ325x25) is the most suitable equipment to bend tube for shipyard.
|
|
|
|
|
|
AddisonMckee manufactures a large range of all-electric and/or Hydraulic CNC tube bending machines from 4mm to 273mm diameter, providing tube bending solutions to the Automotive, Aerospace, Shipbuilding, and niche markets.
All AddisonMckee machines are built using exacting quality standards and enforced by our own Total Quality Assurance program, and feature:
* DataBend CNC Unit
* Foot Pedal Cycle Start
* Clockwise/Anti clockwise bending rotation
* Operator training
* Operator manual and circuit diagrams
* Laser safety scanner
* Safety barrier rail
* Recapture software
* Sequential software
* Safe load procedure (foot)
* CE Mark
Hydraulic:
AddisonMckee hydraulic DataBend CNC tube bending machines continue to provide a durable design and proven technology to traditional markets using the same front-end Siemens Controls as the all-electric machines–and all at a lower cost than the electric counterpart.
Electric:
AddisonMckee electric DataBend CNC tube bending machines are clean and quiet, operating with reduced running and maintenance costs. With sophisticated programming control of machine axis, greater positional control and repeatability is achieved, producing high quality bends. The electric range of DataBend machines are ideal for tight radii, thin walls, exotic materials and close tolerance components.
|
|
AddisonMckee have designed a range of highly-specialized, electrically-powered, hydraulically-operated elbow tube benders. Developed to answer the demands of the plumbing industry, the ElbowBend series is capable of delivering six 90-degree or 45-degree copper elbow joints every 7.2 seconds.
Simple start-up and shut down procedures allow for quick tool changes to be achieved in 25 minutes.
The machines’ control system is based on a Siemens controller, and all electrical control gear and axis drives are integral to the machine – mounted in an electrical cabinet secured to the base frame.
All AddisonMckee machines are built using exacting quality standards demanded and enforced by our own Total Quality Assurance program.
|
|
AddisonMckee's innovative FormMaster-70 Ram Extrusion machine, or FM 70 RE, has been designed to produce small bent components at high speeds with minimal scrap.
In essence, the FM 70 RE extrudes or pushes a near-net tube through a contoured set of dies or clamps, generating one or two shallow bends - typically with a maximum degree of bend of approximately 40 to 45 degrees.
The FM 70 RE machine is perhaps best known for its ability to minimize tube scrap. As opposed to a typical bending process via a standard bending machine where a clamp holds one end of a tube, and a collet holds the other end where these ends are ultimately discarded as scrap - the FM 70 RE eliminates this scrap via its innovative Ram Extrusion process.
|
|
|
|
|
|
Thanks to the new PowerBend range of CNC tube benders, manufacturers requiring standard three axis solutions can now benefit from AddisonMckee's world-leading reputation for quality, precision and reliability at an exceptionally competitive price.
A high-performance draw bending range, designed for the accurate and repeatable production of tubular components, PowerBend models provide levels of accuracy, repeatability, quick tool change and ease of operation as required by today's manufacturing industries.
PowerBend series CNC tube benders—Key range/feature information:
* PB42ST - 42mm (1 5/8”), PB75 - 76mm (3”), PB100 -102mm (4”), and PB150 - 150mm (6”) - models
* Maximum 20 bends per program
* X, Y, Z/Y, B, C axis data input
* Automatic release of tube prior to final bend
* Extensive program storage with USB ports backup
* Allen-Bradley Control Unit, Drives and Motors
* Rexroth Hydraulics
* Foot Pedal Cycle Start
* Recapture Software
* Anticipated Mandrel Retraction
* Safety Scanner and Barrier Rail
* Recapture software & online diagnostics
|
|
Fully electric CNC tube bending machine for tubes with OD 80 mm, 9 axis with 3D visual graphic programming (VGP3D),
FEATURES:
* multiradii (up to 8 tools)
* bend head with left or right hand bending sense configuration
* all the critical machine setting parameters set and managed by the CNC control
* Fixed, variable radius and boost bend up to 5000kg
* High reliability and high productivity
* Use of existing tools - low running costs
* Real time bend simulation automatically selecting the shortest and most efficient bending cycle to minimize cycle time and reduce cost,
* Any possible collision points are highlighted and the most practical avoidance routes effected.
* Axis position is read by absolute encoder eliminating all conventional sensors, increasing reliability, performance and reducing maintenance cost
|
|
|
|
|
|
Characteristics of TNC pipe bender:
-Controlled through PLC and touch control screen and possesses manual, semi-automatic and full-automatic mode.
-All programs can be operated through dialogue mode touching control screen.
-All information is displayed by English and Chinese with simple operation.
-Can set in many different angles to bending by turns.
-Possess automatic error detection function and limit protecting function.
-Guiding module has auxiliary pushing function and at the same time it possesses reiteration and entering repeat functions that can make the guiding module length shorten.
-Counter function can accurately count workpieces quantity.
-Adoption of oil pressure valve accumulative body loop can control actions individually to prolong the lifespan of oil pressure parts.
-Tri-step loop possesses cooling and deposit functions which can avoid the deteriorate oil.
-Optional function of core entering and lubricating automatically.
-Optional function of core reversing slowly.
-Optional function of slow bending.
|
|
|
|
|
|
All models of Comac double pinch style profile bending machine can be equipped with electronic automatic control systems to improve accuracy and consistency of jobs and enhance the rate of automation.
These controls are simple 2-axis programmable positioning devices, or CNC controls.
Programmable positioning devices are useful to join straight parts to bent parts and to perform multiple-passes jobs in a more consistent sequence of operations.
CNC controls are required to accomplish multi-radius curves to be produced in medium-large batches with high consistency and excellent quality of transitions between the different radii, even with difficult materials such as thin-wall tubes.
This can be achieved by controlling simultaneously three axes, i.e. the profile feeding and the positions of the bending rolls.
Among the hundreds of parts produced with CNC-controlled rolls, some samples are: greenhouses, handrails of cruise boats, conveyor rails, variable-pitch pipe coils for boilers, pancake coils, commercial signs, etc.
Two versions of CNC control are available; both are based on industry standard non-proprietary hardware (PLC’s and Industrial PC’s worldwide available), in order to insure immediate availability of spare parts and local technical support.
|
|
|
|
|
|
NC series
NC Control Pipe Bender with Hydraulic Rotary Bending
Cost Effective and easy to bending pipe
The NC Series Tube Benders
The NC series tube benders equipped with NC control unit with Touch Screen Interface. It combines easy-to-use operation with high pipe bending accuracy and cost effectiveness. It is the practical semi-automatic tube bending solution for small to medium productions.
SB-80NC
NC controlled tube bender, with Touch Screen and capacity up to Ø88.9mm. Hydraulic Draw bending pipe bending machine
NC tube and profile bending machine features:
· NC control unit with Touch Screen
· Easy operation interface and enable easy data input
· Large program capacity storage
· High pipe bending accuracy up to +/- 0.15°
· Self diagnosis & error messages on-screen display
· Hydraulic clamping with optional pressure die assist
· Suitable for various materials such as steel, stainless, aluminum and copper
Keywords
Pipe Benders,Tube Benders,Tube Bending,tubing bender,bending pipe,Pipe Bending,Bending pipe Machine,Tube Bending Machine,Pipe Bending Machine,tube cutting,metal saw,Circular Saw,Sawing Machine,tube cutter,pipe cutting,pipe cutter,circular sawing machines,Saw blades,chamfering machine,deburring machine
(Pipe Benders - Tube Benders - Tube Bending - Pipe Bending - Bending Machine - Tube Bending Machine - Pipe Bending Machine - Circular Saw - Sawing Machine - Cutting Machine - Deburring - Tube End Finishing, Bender Tube, bender Pipe, Cutting, Chamfering Machines, Deburring Machines, CNC Tube and Bar Machining Center, HSS saw Blade )
|
|
A production machine for 3 applications :
- cutting
- punching
- bending flexible and rigid bars
Very quick tool changeover.
2 drive systems available :
- hand-operated hydraulic pump
- electro-hydraulic unit
|
|
The "Ready to Operate" high end busbar fabrication system for large production scales.
Three individual stations for cutting, punching and bending of busbars up to 160x13mm (6"x1/2").
Fast and easy workflow due to conveyor links between all stations. The foremost busbar fabrication from Novopress with "DigiPunch 160" and BGD-4, for unsurpassed precision on all punching and bending jobs
|
|
CON-O precision contour burning and beveling machines produce elliptical cuts and bevels in pipes and cylinders.
The CON-O automatically follows symmetrical surfaces to produce smooth, accurate cuts and bevels. It is portable and easily taken to the work. The CON-O locates from a center-punch mark and is set to a radius mark. Powerful permanent magnets stabilize the machine (two outrigger support kits are supplied with the CON-3 and CON-4, four outrigger support kits are supplied with the CON-5.
|
|
Tube Terminator
Hand-guided one-step crimp/seal copper and aluminum tube welder
Seals refrigerator/air conditioner tubing -- even when charged
Produces quick, airtight bonds without brazing
|
|
We offer you a wide range of modern storaged parts of installation material with suitable crimping technology and also the needed accessories. You need only one supplier for covering your whole requirements.
Please contact us directly for technical support.
|
|
|
|
|
|
We offer a complete line of hand tools to accommodate virtually all the needs of low volume manufacturing, prototyping, maintenance and repair. From manual tools to battery and electrically powered units design for performance. Our tools combine ease of use with reliability and precision.
Standard Die Envelope (SDE) Crimp Tooling
The SDE Tooling System allows use of the same dies across a range of application platforms. They serve your needs at the bench, in the lab, in production or in the field without fitting dies for each tool required.
CERTI-CRIMP Hand Tools
CERTI-CRIMP Hand Tools are top-of-the-line, premium, hand-operated tools for crimping a broad array of terminals, contacts and special wiring devices.
Hydraulic Crimp Tooling
New 10,000 psi-rated tools with industry-standard U-Dies, also available with portable, powered pump
Battery Crimp Tool Kit
This completely portable battery-operated hand tool weighs only 3.5 lbs including battery. It has a pressure sensitive cycle control and can perform about 100 crimps per charge.
626 Pneumatic Tool System
This versatile Pneumatic Tool System provides the ultimate in wire range flexibility for higher volume operation. It's available with hand or foot-operation configurations with ratchet control.
Pistol Grip Tooling
The Pistol Grip Hand Tool System uses interchangeable terminating heads to apply a broad range of IDC products.
|
|
The CHAMPOMATOR 2.5
Terminating Machine is a
compact, semiautomatic
bench machine for terminating
multiconductor, jacketed
cable with a variety of
AMP connectors having
insulation displacement
contacts. It is microprocessor
controlled, and programmed
using a membrane-
switch keyboard.
Pertinent information for
operation, including diagnostics
and error conditions,
is displayed on the
control module.
|
|
These versatile hand tools and dies are ideally suited for R & D, networking
applications and on-site maintenance work.
• User-adjustable ratchet control for a complete crimping cycle
• Emergency ratchet release
• Angled head, providing a comfortable hand and wrist position
• Over 100 interchangeable SDE die sets for crimp a broad range of connectors
• Able to handle multiple wire and terminal sizes in one die set
|
|
|
|
Tools for Pipes, Tubes, Cables
