Pipe and hose accessories

Pressure gauge cocks provide the opportunity to either vent the connected pressure gauge according to the position of the handle (venting position), i.e. put it into a pressure-free state, or to vent the pressure measuring instrument ...

When a reduction of pressure or a limitation of the flow rate is required a restriction orifice must be inserted into the pipeline. Our technical department will evaluate the correct design for the restriction orifice, depending on customer ...

QuickHeat Hose System Hose Set for Foam Application Faster, more consistent heat to finish the job sooner. Overview We heard your frustrations and tackled three key issues facing spray operators: not enough DeltaT, warm-up takes too ...

Hosco PA Hose Connectors are designed to provide safe and non-conductive connections of hose and tubing using the robust and industry leading Hosco barb and nut style retention system. These connectors significantly exceed the performance ...

Stainless Steel Restrictors provide reliable, long life fluid flow control to an applicator. The family of products consists of recirculating and non-circulating versions that can be internally set (tamperproof) or externally adjusted ...

. Bore Ø: 6, 10, 20, 30, 40 mm . Flow rate: between 200 et 5000 Nl/min . Material: Aluminium By virtue of the COANDA effect, the motor flux draws in air at room temperature. This physical phenomenon greatly amplifies the flow which ...

Air Amplifiers, with the COANDA effect, MD series Presentation . 2 models . Bore Ø : 25, 38 mm . Flow rate : between 2015 and 4370 Nl/min / between 82.95 and 152.95 SCFM . Material : Aluminium By virtue of the COANDA effect, ...

BestaPower A180 The A180 aluminum profile with integral compressed air supply and high load reduces the need of the steel structure. Its compatibility with the A62 profile, grooves on three sides that allow the installation of energy ...

BestaPower W5 - traxX The automation solution with integrated compressed air line, sideways installed energy-guiding chain and optional position gauging system. Special features - The optimal compressed air supply, even for users ...

BestaPower A62 The A62 aluminum profile with integral compressed air supply is suitable for use with tapping valves and tapping carriages, as well as for continual energy supply with a laterally suspended energy guiding chain. Special ...

Molded orifices are the simplest method of flow control and are one of Air Logic's best-selling product lines. They work on the principal of Flow Restriction with the orifice diameter being identified in the part number and by color codes ...

EXAIR's Super Air Amplifiers are patented to reduce compressed air use and increase ambient air amplification. They move a large amount of air by creating a uniform, focused, high velocity blast of air that draws in surrounding air for ...

Filtered orifices build on Air Logic's orifice product line with additional protection of an integrated filter. Orifices work on the principal of Flow Restriction with the orifice diameter being identified in the part number and by color ...

The trolley on hollow bar is equipped with 6 ball bearing wheels running on HBS 50 profile. The hollow bar has a double function: track for the trolley and conduit for compressed air. This trolley is recommended for high flow and heavy ...

Diameter: 12 mm - 100 mm
Temperature: 1,200 °C - 1,500 °C
Length: 25 m - 50 m

The Texil® sleeve is made of Texil® yarn, an excellent insulator; it does not irritate and withstands a continuous temperature of 1000°C. The sleeve is suitable for insulating pipes, protecting them against slag. It is an excellent ecological ...

Diameter: 12 mm - 60 mm
Temperature: 550 °C
Length: 25 m - 100 m

Texpack® sleeves are made entirely of 6-9 μ Texpack glass fibres. These only melt at very high temperatures. On request, rubber pipes can be sleeved. Applications Lagging for pipes, lagging for hoses and electric cables.

Diameter: 12 mm - 60 mm
Temperature: 550 °C
Length: 25 m - 100 m

Tricosleeve glass sleeve is produced by knit braiding. Although the thickness of the wall is thinner than that of the classic glass sleeve, due to the different type of braiding, it is a soft and flexible product. The maximum operating ...

The TFG – TFR 1000 series includes hydraulic flexible hoses 1/4 – internal Ø 6.3 mm, working pressure 1000 bar. • Also available in custom sizes and types. • Flexible hoses can be equipped with quick couplers. Series TFG – TFR ...

The FITT Sewer EVO pipe according to UNI EN 1401 for sewage and industrial drains not under pressure, guarantees superior performance thanks to the exclusive joint system with integrated, non-removable gasket. The Environmental Product ...

Overhung Load Adaptors (OHLA®) are mounted to hydraulic motors and pumps to prevent premature equipment wear by supporting heavy radial and axial loads. They also protect hydraulic fluid and pump and shaft seals from dirt, grime and other ...

Non-SAE Mount Overhung Load Adaptors 4-bolt mount overhung load adaptors absorb stress to help prevent premature motor or pump failure caused by axial or radial overhung loads on motor pumps and shafts. Non-standard overhung load adaptors ...

The Model 200 Series of SAE A mount Overhung Load Adaptors (OHLA®) provide radial and axial load support to extend the lifespan of mobile hydraulic systems. Model 200 OHLAs are compatible with shaft diameters up to 1” and provide the ...

Diameter: 0.25 in - 2 in
Length: 6.4 mm - 38.1 mm

5/16″ Hex extension fitting with 10-32 male to 10-32 female threaded connections. Models are available with shouldered lengths ranging from 1/4″ to 2″. Max Pressure Rating: 1,000psig brass 3,000psig stainless steel Features ...

Diameter: 6 mm
Length: 20 mm

M6 male to 10-32 female threaded straight adapter. Max Pressure Rating: 1,000psig brass 3,000psig stainless steel Features Beswick adapter fittings provide a convenient method for adapting Imperial/English threaded components ...

10-32, M5 or M3 female to male threaded fitting with micro-drilled orifice for precise flow restriction. Max Pressure Rating: 10-32 and M5 threaded configurations are rated to 1,000 psig in brass and 2,000psig in stainless steel. M3 ...

Width: 0.062 in - 0.22 in

SINGLE WIRE The single wire concentrates the clamping force in one specific area around the hose to give the most effective holding force and clamping strength.

Width: 0.082 in - 0.142 in

SLIM WIRE A slimmer version of the single wire hose clamp. The single wire concentrates the clamping force in one specific area around the hose.

Width: 0.039 mm - 0.137 mm

DOUBLE WIRE A cost-effective choice for applications where a lower clamping force than offered by single wire clamps is sufficient and aesthetics are important.

COUPLERS The external coupler [DAC-E] consists of two parts: a fixed part for connection to the plant and a movable part connected to the pump by means of an optional threaded connecting pipe. The two parts can be connected and disconnected ...

COUPLERS The bottom coupler with vertical discharge DAC-V is compact and rugged, suitable for installation in small pits. It allows the pump to be connected to the system and easily disconnected for servicing or storage even without ...

COUPLERS DAC-V vertical discharge bottom couplers for use with pumps up to 1300 kg. Fixing by means of sliding flange or hook [KGP] (discharge DN350) with double guide pipe. A PATENTED guide pipe connection system that reduces mechanical ...

Diameter: 8 mm - 100 mm
Length: 25 mm - 87 mm

MALE / MALE REDUCER - STAINLESS STEEL 316L Inox 316L usiné EXAMPLE OF ORDER : 652413-86

Diameter: 8 mm - 50 mm
Length: 26 mm - 57 mm

FEMALE / MALE ADAPTER - STAINLESS STEEL 316L (Model : 5243)

Diameter: 6 mm - 80 mm
Length: 25 mm - 65 mm

FEMALE / MALE REDUCER - STAINLESS STEEL 316L (Model : 5238)

Rubber flexible tubes must be supplied in coils (max. length 15 mt) with the fittings loose, for assembly in the desired lenght, on the customers promises.

Diameter: 24 mm - 69 mm

Normative Regulation : EN 11423 previous DIN 2826 Coupling Material : Carbon Steel , Stainless Steel , Brass Gaskets Material : NBR , FPM, PU , Novapress® Working Pressure : 18 bars for Steam / 40 bars for Air or Water Connection ...

Diameter: 0.5 in - 12 in
Operating pressure: 10 bar - 40 bar

Normative Regulation : EN 14 420-4 Coupling Material : Stainless Steel, Carbon Steel (other on request) PTFE – PFA or CTFE Coated on request Working Pressure : (ANSI 150 LBS and 300 LBS on request) Connection Mechanism ...

Diameter: 0.5 in - 8 in
Operating pressure: 10 bar - 40 bar

Normative Regulation : EN 14 420-4 Coupling Material : Stainless Steel, Carbon Steel (other on request) PTFE – PFA or CTFE Coated on request Working Pressure : (ANSI 150 LBS and 300 LBS on request) Connection Mechanism ...

Hose diameter: 6.4 mm - 50.8 mm

• Lightweight compact design • Reusable! Attach/re-attach clamps • Easy installation – requires only a screwdriver or hex head wrench • High-sealing pressure with only 10-15 in/lb of torque These hose clamps have been designed for ...

Hose diameter: 19.5 mm - 63.5 mm

ANVER’s CLAMP-P Series of Adjustable Plastic Component Mounts help to quickly, easily, and efficiently secure a variety of components (transfer tubes, air movers, mufflers, etc.) without any special tools required. The clamps are flexible ...

Hose diameter: 30.5 mm

Interconnect the air rod to its flat or round

The pivoting base allows a guy-wire-supported pole to be fixed to a ridge

Down Conductor fixing on tube. Self-locking collar which is permanently tightened around its support thanks dedicated pliers (ref P6060).

An economic and compact source of amplified air, or nitrogen, for high pressure industrial applications. Haskel air pressure amplifiers offer the most comprehensive operating range in the industry, combining simple principles of operation ...

The Air Pressure Amplifiers of the AA Series are single-stage, single-acting amplifiers that have the capacity to yield a total pressure outputs of 4,500 psi or 310 bar.

Double acting, single stage air pressure amplifier with pressure outputs 4,500 psi (310 bar). Pumps twice the volume per cycle of AA series. Requires less air drive since the inlet air pressure itself provides a substantial portion of ...