|
|
SERIES AP 72 VACUUM GENERATOR MODULE Venturi — Shut off valve — Check valve Monoblock vacuum venturi, diaphragm valve and check valve
Compact design Manual or pneumatic , actuation options ; Constant bleed option 5, 8 and 15 slpm of N2 @ 80 psig (5.5 bar); 26 in. Hg (100 Torr) of
vacuum generated with 80 psig (5.5 bar) and 60 slpm of Nitrogen
Stainless steel 316
|
|
|
|
|
|
HV-SA series
Central ejector based on the Venturi principle. Includes two pressure supply ports and a vacuum connection.
When connection 1.1 is supplied with pressure, the Venturi nozzle generates vacuum.
An integrated check valve at connection 2 maintains vacuum in systems with slight leakage even when the ejector is switched off.
The integrated (automatic) air saving feature turns off the air supply to the ejector when the pre-set upper vacuum level is reached. If the vacuum level drops 150 mbar below this level, the air supply is turned on to the ejector until the pre-set vacuum level is reached again. This fulfills the "EMERGENCY ON FUNCTION".
To release the components that have been picked up, a momentary blow off ejects the components (a signal interrupter integrated into connection 1.2 stops the blow off function after 0.3 seconds).
An external 5/2way double solenoid valve is recommended to control the ejector by alternately activating connection 1.1 (start) and 1.2 (release).
Change "release" to blow off as seen on page 66.
The pressure supply port and vacuum connections are fitted with removable protective filters, which serve to protect the ejector from debris.
A silencer with self-cleaning granular filling (with an air consumption of 150 and 300 Nl/min) or a surface mounted silencer (with an air consumption of 500 Nl/min) is included in the scope of delivery.
|
|
# Direct vacuum generator - DP 2010 E
It is a simple valve of compact construction which generates a vacuum when compressed air is applied. The vacuum ceases immediately when the air supply is removed.
# Two-way vacuum generator - DP 2018 F
This two-way valve with integral non-return valve generates a vacuum when air is applied to the pressure port. For applications that do not require a sustained vacuum the valve can be used without the integral non-return valve.
# Vacuum driven liquid sprayer - DP 2005
This valve works on the venturi principial and is primarily used for air driven liquid spraying applications such as conveyor lubrication and sawing machines.
# Vacuum driven liquid sprayer with push-in fittings for ø4 tube - AT.005.4
This valve works on the venturi principial and is primarily used for air driven liquid spraying applications such as conveyor lubrication and sawing machines.
|
|
ICEsonic S-series Air Amplifier.
For an efficient hi-flo operation.
Compact design and no maintenance required.
Products such as ground spices and flour or wastes from textile and paper, fumes and dust can all be conveyed over considerable distance.
Available: Anodised Aluminium and Stainless Steel, from 5 to 50 mm.
|
|
|
|
|
|
Air Conveyors - Ring-Vac™ Pneumatic Conveying System:
Available in standard and threaded versions for regular and high temperature applications.
Air Conveyors - Ring-Vac™ Pneumatic Conveying System has virtually no moving parts, convey's air at high rates and long distances. Utilizing compressed air for a powerful, efficient venturi action along its length in a compact design for high capacity conveying over large distances.
Air Conveyors - Ring-Vac™ Pneumatic Conveying System is available in both coated aluminum or high temperature stainless steel. Simply clamp a standard hose size to each end of the Ring-Vac™ to create this high energy conveying system. No moving parts for maintenance free operation with capacity and flow controlled with a pressure regulator.
Air Conveyors - Ring-Vac™ Pneumatic Conveying System is available in 1" (25mm), 1-1/4" (32mm), 1-1/2" (38mm), 2" (51mm), 2-1/2" (64mm), and 3" (76mm) sizes. Any size beyond that can be prohibitive for most applications due to high compressed air requirements.
In addition, beyond 3", the vacuum ability begins to drop significantly except for highly intermittent applications. For applications beyond 3", a blower system often becomes far more economical except in a rare number of possible applications. However, larger size versions are available if required as well as special sizes.
Coated aluminum and high temperature stainless steel Ring-Vac™ Air Conveyor can convey all types of solids in large volumes over great distances with no moving parts.
- Made of an coated aluminum body with no moving parts. High temperature stainless steel models are available for high temperature and corrosive applications.
- Standard sizes to fit standard hose diameter for easy clamping. Threaded versions connect easily to regular pipe thread: 1" (25mm), 1-1/4" (32mm), 1-1/2" (38mm), 2" (51mm), 2-1/2" (64mm), and 3" (76mm). Special sizes can be manufactured if required.
- Utilizing a pressure regulator will control the flow material.
- Instant ON/OFF with no moving parts, no electricity or explosion hazard.
- Longer life in difficult environments than competitive models.
- Ease of use.
- Simple and easy control of material flow.
- Maintenance free operation.
|
|
Conveying Pump (Air Movers)
>> VTRA Pump Series
This is a series of adjustable flow rate single stage vacuum pumps particularly good for use in high contamination areas where dust and small debris is likely to enter the vacuum line.
The design of this pump enables particles and small debris to pass directly through the pump. High flow rates can be achieved in conjuction with vacuum levels down to -84.4kpa whilst maintaining a high performance to air consumption ratio.
>> VTRF Pump Series
These pumps provide a reliabel and cost effective solution for in line product transfer, particularly for transferring bulk materials, granules, continuous strips and powders. Like the VTRA the pump has a straight through design, hence they are non-clogging and maintenance free. High flows can be achieved with in line bore sizes up to 1 1/2".
|
|
Parker’s RG01 Nozzle, Venturi, and Hot-Gas Bypass Distributors are used for two-phase refrigerant distribution to coils. These need to be mated to a Parker Fixed Restrictor Assembly, a thermal expansion valve (TXV), or other device for refrigerant metering.
* Various nozzle orifice sizes are available for distributor housings.
* Nozzle-style distributor-housings are available for air-conditioning and heat-pump systems.
* Venturi distributors are available with a wide range of configurations and hole sizes.
|
|
Many different things can be transported here. Any piece of pipe will come alive when a "pipe vacuum ejector" is installed.
Compressed air is blown through an annular gap and off it goes. You now can transport items from one place to another at an incredible speed - with low air consumption. One could get the idea to replace a robot with it and use the PVF as a handling unit.
The PVF has a solid outside, no movable parts, meaning a good application range for heavy duty tasks.
Simply an ingenious solution. Try it out and let your phantasy go wild. We will be happy to hear about each new solution you discover - because it is so simple!
|
|
Venturis
Venturis add to the cleaning efficiency of pulse-jet baghouses. Standard Filter offers a wide variety of styles and sizes for both top and bottom removal cages. We can supply either spun or cast venturis manufactured from carbon steel, stainless steel, aluminum or galvanized steel.
|
|
|
Electric and Compressed Air Powered Vacuum Pumps, Vacuum Generators and Vacuum Stations, Vacuum Valves and Switches, Vacuum Filters and Exhaust Mufflers, Air Movers and Transfer Tubes, and a wide range of Vacuum System Accessories, all available at competitive prices.
|
|
Theis is most significant model base on the multi stage principle Low compressed air are required far massive evacuation volumes at high vacuum flow and high vacuum level rate. V-tec air saving kit is available in this pump in order to maximum reduce the energy usage. VITON & EPDM seals can be also stipulated as option.
|
|
The Kavac series of vacuum products includes a wide variety of conventional vacuum components, as well as more specialised items such as variable vacuum pumps, material transfer and air amplification units. KV's vacuum division is also able to deliver customer-specific vacuum solutions; often developing customised pumps or completely integrated vacuum control systems. A comprehensive range of vacuum cups complements the Kavac range.
|
|
* Large vacuum flows
* Short evacuation time
* Good for handling porous materials or if leakage is present
* Energy-Saving (ES) available
* Available with connection plate in aluminium (AD) and composite PPS (D).
|
|
| ... products without technical information |
| |
|
|
Ejectors, Venturi
