|
|
|
|
|
|
The centrifugal immersion pumps of building group 4 are used for wet-pit operation in containers, pits and tanks. Centrifugal immersion pumps for dry-well installation, i.e. to be installed and operated outside the container, are also available.
All components of pumps in plastic design that are in contact with the fluid are made of PP or PVDF. The pump shaft consists of a motor shaft made of stainless steel and a shaft-protecting tube of either PP or PVDF. Built-in elastomers are made of FPM (or also EPDM without surcharge). Centrifugal immersion pumps are equipped with overhang shafts so that there is no need to provide for shaft bearings in components that are in contact with the fluid. Thus, the pumps are safe to run dry and do not require regular service and maintenance.
There is no need of a mechanical sealing of the shaft. Only a so-called gas seal is installed beneath the motor to prevent aggressive vapours from penetrating the motor chamber. But this seal is never in contact with the fluid delivered.
- For aggressive and neutral liquids
- For short-term and continuous operation
|
|
|
Under the SP fluid the dregs thick liquid pumps forthe verticalcentrifugal dregs thick liquid pumps, plunges underthe fluid, uses into transport the abradability, the thick pellet, the highlyconcentrated dregs thick liquid. Does not need any axis to seal withthe axis seals the water, is insufficient in the absorption quantityunderthe operating mode also can the normal work. SP pumps has flowed the part to be made by the wear-resisting metal. SPR pumps plunges underthe fluid the spare part to bring the rubberouter lining, is suitable to transporting the non- edges and cornersthe abradability dregs thick liquid. According to the dregs thick liquid pond liquid level height, maychoose the different length the pump driving shaft orthe inductionpipe. Uses the many kinds of speeds and the many kinds of aberrations way.causesto pump underthe best operating mode moves, service life long.the movement benefit is high, can satisfy many kind ofbadtransportations condition.
|
|
Features :
WIDE RANGE OF
APPLICATIONS:
- Industrial Process
- Corrosive Liquids
- Paint
- Waste Water
- Chemical Slurries
CAPABILITIES:
- Capacities to 3000 GPM
- Heads to 230 Feet
- Temperature to 400 d. F
- Pump Length to 6 feet
- Shaft Diameter to 5"
CONSTRUCTION:
- Cast Iron
- 316 Stainless Steel
- Alloy 20
- Hastelloy
- CD4MCu
|
|
Type: single-stage, single-flow, open impeller
Head: up to 35 m
Flow rate: up to 800 m³/h
Pressure: up to 10 bar
Temperature: up to 60°C
|
|
SPP Pumps have been manufacturing fire pumps for over 130 years with one of the widest range of approvals of any manufacturer in the world. Experience gained from extreme environments such as off-shore oil & gas installations has led to the creation of the SPP UL Vertical In-line range of fire pumps approved for fire protection by Underwriters Laboratories and fully compliant with NFPA 20.
The SPP line of vertical in-line fire pumps are lightweight and compact for smaller pump rooms. They eliminate the need for coupling alignment and there are fewer lost or misplaced parts.
|
|
Every wetted component in a Vanton SUMP-GARD® vertical pump, including the heavy-wall shaft sleeve, is offered in PVC, CPVC, PP, PVDF, and other non-metallic materials compatible with the pumped fluid. This eliminates corrosion and minimizes abrasion, resulting in lower maintenance, longer pump life, and contamination-free products. SG pumps are configured for sumps to 50 ft. (15 m) deep, and handle flows to 1450 gpm (330 m3/hr), heads to 245 ft. (85 m), and temperatures to 275°F (135°C).
SUMP-GARD pumps are ideal for the transfer and treatment of process fluids, plant effluents and industrial or municipal water and waste streams. They are available with vortex pump heads to pass sludges, slurries and stringy materials as well as fluids with solids to 3 inches (75 mm) in diameter
|
|
900 Series Single Stage Inline Fire Pumps
VERTICAL Inline Close Coupled Fire Pumps are specifically designed for vertical mounting. The suction and discharge nozzles are located on the same centerline 180° apart. Vertical pumps significantly reduce required mounting space. They are easy to maintain. Simply remove eight capscrews and the motor and bracket assembly is easily removed fiom the casing without disturbing the piping. The impeller is direct coupled to the motor shaft for easy maintenance, to minimize impeller run out and to reduce noise.
Features:
- Bronze fitted pump construction
- Bronze shaft sleeve
- Split bronze packing gland
- Carbon steel shaft
|
|
API 610 9th edition, fully compliant VS4 pump!
The Model 3171 is the Veteran vertical sump and process pump. Thousands of installations in industrial process, sump drainage, corrosive liquids, pollution control, molten salts attest to the 3171's remarkable performance. Simple mounting.
Self-Priming
Rugged Double Row Thrust Bearing
Heavy Duty One-piece Shaft
External Impeller Adjustment
Available in a Wide Range of Alloys
Open Impeller Design
Vapor Proof Option: Choice of packing, mechanical or fluid sealing methods to seal sump vapors
Capacities to 3180 GPM
(722 m3/h)
Heads to 344 Feet
(105 m)
Temperatures to 450° F
(232° C)
Pit Depths to 20 Feet (6 m)
|
|
ITT Flygt WC & YDD (Pewaukee US)
Technical features:
Design: Vertical turbine “pull out”
Size of outlet flange: according demand
Max. liquid temperature: according demand
Max. Flow: 90.000 m3/h
Pump sealing: Mech. seal or packing.
Max. Head: 25 m
Max. operating pressure: 10 bar
Shaft Impeller Column Pump seal
AISI 410 AISI 316 GG 25 Customer choice
Duplex Duplex or Super Duplex
ITT Vogel WM (Peewaukee US)
Technical features:
Design: Vertical turbine
Type of impeller: enclosed
Max. Flow: 60.000 m3/h
Max. Head: 175 m
Max. operating pressure: 25 bar
Shaft Impeller Column Pump seal
AISI 410 AISI 316 GG 25 Customer choice
Duplex Duplex Duplex
Super Duplex Super Duplex Super Duplex
|
|
Features and Applications
The EVM(R) series pumps are vertical, centrifugal slurry pumps submerged in sump during operation. They are designed for delivering highly abrasive, large particles and high density slurries. These pumps have no need of any shaft seal and sealing water. The pump casing of type EVM pumps are made of wear-resistant metal. The wear parts are made of high chromium for the EVM series and are rubber lined for the EVR series.
The submersible pumps are suited for handling abrasive or corrosive, dense slurry with large particle size.
Notation
EVM(R)-65Q
E:Excellence
V:Vertical type
M:Metal lined
R:Rubber lined
65:Discharge size (mm)
Q:Frame type with maximum power
|
|
Warman 5000
Metal and elastomer high head vertical slurry pumps
Features / Benefits
- Cantilevered shaft design
- Double suction, semi-open impeller
- Elastomer or abrasion resistant metal construction
- Agitator option keeps solids in suspension
- Optional suction extension
- Universal motor bracket accomodates several motor sizes
- Dual casing balances radial loads on shaft and bearings
|
|
NL type sewage and slurry pump
- widely applicable
- can be used for draining flooded fields and fighting droughts
- durable、wearproof
- pleasing shape
- convenient maintenance
- as simple ambulatory fire fighting pumps in the village
- widely applicable
- safe and reliable
|
|
Moyno Vertical Pumps
The new Moyno® Vertical Pump takes progressing cavity performance to new heights. It can be flange mounted to closed tanks or affixed to mounting beams above open tanks. With its inlet submerged, the pump pulls fluid from the bottom of the storage vessel and discharges it at the surface for further processing downstream.
|
|
APPLICATIONS
* CIVIL AND INDUSTRIAL WATERS HANDLING PLANTS
* PRESSURIZZATION PLANTS
* WATER SUPPLY FROM RAIN WATRE TANKS OR RESERVOIS
* SPRINKLER SYSTEMS
* FOR APPLICATIONS REQUIRIG OPTIMISED PUMP SILENCE AND MOTOR COOLING FEATURES
DESIGN ENGINEERING
* OIL BATH MOTOR (BIODEGRADABLE AND DIELECTRIC) FOR COOLING AND BEARING LUBRIFICATION
* DOUBLE MECHANICAL SEAL:
ENGINE FACE: OIL BATH
PUMP FACE: WATER BATH
* PERMISSIBLE DRAUGHT OF WATER: 5 m
* IP 68 PROTECTION CLASS.
* CLASS “F” INSULATION.
* MAX. PUMPED LIQUID TEMPERATURE: 50°C
|
|
Construction
- Vertical column sump pumps, with motor in dry installation and with pump body submerged in the liquid handled (without suction line or foot valve).
Impeller:
- VAL: free-flow impeller (vortex or recessed impeller).
- SC: open impeller.
Applications
- For draining a basin or a sump with domestic or industrial sewage.
- For slightly dirty waste water, for liquids which are non-aggessive for the pump materials.
|
|
General, Field of Application
The DICKOW submerged pump is a one or multistage centrifugal pump of vertical construction. The performance range covers capacities up to 500 m3/h (2200 USgpm) at differential heads up to 300 mLC (984 ft) and is subdivided such that best efficiency is granted at all service conditions.
With a wide selection of material, several constructive variants and shaft sealings, the HZV-pumps are suitable for handling most of all liquids as long as they are of low viscosity and free of solids.
Examples of application are unloading of fuels and solvents from buried tanks, pumping kerosine in hydrant plants for aircraft fuelling (PTB-design) as well as recirculation of condensate (barrel suction design).
|
|
General
The DICKOW submersibe pump, type NCT, for the chemical industry is a vertical pump with separate discharge pipe.
The maximum capacity goes up to 700m³/h. Higher capacities are available.
The pump type NCT has been developed for chemical, petrochemical and related industries. With a wide selection of materials, the DICKOW submersible pumps are suitable for handling almost all liquids which are used in above mentioned industries.
For example: acyds, lyes, hydrocarbons, condensation products, solvents etc.
|
|
|
The EPG TSP Submersible Pump with level sensor mount is designed with the small diameter vertical well in mind. This pump can be used to pump groundwater, leachate, and other contaminated liquids. It is able to be installed in wells as small as four inches in diameter. When used in conjunction with EPG's LevelMaster Level Monitoring Control System the benefits of continuous accurate monitoring and control of liquid levels in a small diameter well are achieved.
|
|
Bearing Free, Sealless 316 Stainless Steel Vertical Pumps
Designed for Corrosive Liquid Applications
The “ZSX series” stainless steel vertical pumps are completely corrosion resistant and are recommended for transferring, recirculating and agitating a wide range of chemical, laboratory and industrial process applications.
Like our popular “ZDX” series, these stainless steel models incorporate a unique opposing twin-impeller design. The design feature provides high volume circulation and eliminates leakage up the pump column. No bearings or seals permit dry running without damage.
The pumps are engineered to provide flows up to 100 GPM (378 LPM) and pressures up to 68 TDH (20 M). All wetted parts are precision manufactured from 316 stainless steel.
|
|
NEMO® Immersible Pumps are used for emptying barrels, tanks, and pits. They are also used where space is limited and the danger of cavitation may be present. In addition, these pumps are suitable for emptying barrels containing materials hazardous to water and the environment.
Features of the NEMO® BT Immersible Pump:
- compact design
- high pressure stability
- low-pulsation conveyance
- high suction capability
NEMO® BT Immersible Pump offers you:
- immersion depths of up to 15,000 mm
- low life cycle costs
- high efficiency
- high variety of shaft sealing systems
- easy serviceability
Advantages of the NEMO® BT Immersible Pump
- can be operated under high conveying pressures and at high capacities
- capable of pumping a great variety of substances
- capacities can be adjusted proportionally
- four different geometries for adjusting to the given application
|
|
Salient Features
* "BA" Series pumps are designed with ‘bonded to metal’stator; encased/threaded to pump barrel to suit narrow opening of drums etc.
* Driven by flange-mounted motors, suitable for vertical operation.
* Long Coupling rod and pump casing to suit immersion depth.
* Wide choice of materials to suit corrosive and / or abrasive media.
* Standard Design incorporates a Mechanical Seal with open box type housing
* Open pin Joint for clean in place (CIP) where food / edible products are to be handled.
|
|
SP Submersible Borehole Pumps
Applications: Water supply, irrigation and dewatering duties for domestic, commercial, municipal and industrial applications
Duty range: Flows to 280m³h
Heads to 620 metres
Temperature range: 0°C to +40°C
Connections: 1¼" to 6" BSPF
Borehole sizes: 4" to 12"
SQ Compact 3" Submersible Pumps
Applications: Borehole water supply for domestic/light commercial use
Duty range: Flows to 9.8 m³h
Heads to 200 metres
Temperature range: 2°C to 40°C
Pressure rating: 16 Bar
Pump connections:
Borehole size: 1¼"/1½" BSPF
3"
|
|
* Applications:
Wet Pit,Agriculture,Chemical Processing,Effluent,Sump Service,General Purpose,Water Treatment,Hydrocarbon Processing,Recycling Services,Environmental Services
* Industries:
Water Handling and Treatment,Waste Processing,Utilities,Auxiliary,Miscellaneous Services,Water Treatment,OEM
* Standards:
* Misc:
Optimized Lineshaft/Shaft Bearing Design complies with API 610 spacing requirements, virtually eliminating shaft failure and extending Mean Time Between Planned Maintenance (MTBPM).
Externally Adjustable, Semi-Open Impeller minimizes clogging and reduces costly downtime.
Rigid Coupling with fully enclosed impeller adjusting mechanism, protected from environmental fouling, allows simple external setting of impeller.
Double Row External Thrust Bearings prevent pump developed loads from being transmitted to the motor, avoiding costly motor failures.
|
|
Offering state-of-the-art hydraulics, CPXV ISO vertical sump pump is designed for applications where high performance, superior efficiency and low NPSH are required. CPXV ISO pumps conform to ISO 5199 design criteria.
* Flows to 1400 m3/h (6160 gpm)
* Heads to 250 m (820 ft)
* Pressures to 25 bar (365 psi)
* Temperatures from -40°C (-40°F) to 350°C (660°F)
|
|
|
|
|
|
Introduction of Vertical Slurry Pump —— EVM(R) Series
The EVM(R) series pumps are centrifugal, vertical slurry pumps submerged in sump during operation. They are designed for delivering highly abrasive, large particles and high density slurries. The sump pumps are suited for handling abrasive or corrosive, dense slurry with large particle size.
The features of this kind of Vertical slurry pump
This sump pump casing of type EVM pumps are made of wear-resistant metal. The wear parts are made of high chromium for the EVM series and are rubber lined for the EVMR series. According to liquid surface of the slurry pool, the vertical slurry pump transmission shaft and suction pipe could be chosen. The sump pump could operate under the best condition with different speed.
Main application of this kind of Vertical slurry pump
The vertical slurry pumps are designed for delivering abrasive, large particle and high-density slurries and applied over the fields such as metallurgy, mining, coal, power, building materials, and environmental protection
|
|
The Model 3171 is the Veteran vertical sump and process pump. Thousands of installations in industrial process, sump drainage, corrosive liquids, pollution control, molten salts attest to the 3171's remarkable performance. Simple mounting.
Specifications:
Capacities to 3180 GPM (722 m3/h)
Heads to 344 Feet (105 m)
Temperatures to 450° F (232° C)
Pit Depths to 20 Feet (6 m)
|
|
520 Series; Single Stage Sump pump
Pump Features:
- bronze Sleeve Bearing is extra length for long life
- Relief Holes prevent liquid under pressure from rising above normal sump liquid levels
- Capacities to 110 G.P.M (25 M3/HR)
- Heads to 40 feet (12 Meters)
- Temperatures to 180°F (82°C)
Applications:
- Condensate Service
- Light Duty Sump Service
- Dirty Liquid Service
|
|
EPG’s SurePump Vertical Sump Drainer (VSD) pumps contaminated liquids for recovery, leachate collection, gas condensate removal, and sampling applications. It can be used in aggressive environments. Other designs may fail while EPG Vertical Sump Drainers are still going strong. EPG backs the vertical sump drainers with a one year warranty effective the date of installation.
- Stainless steel construction
- Corrosion resistant
- E-Glide bearings for extra durability
- Teflon seal rings
- Franklin Electric motor
- Sealed unit with liquid flow drawn past motor for cooling
- Facilitates drawdown to the very bottom of the vessel
- Chemical resistant jacketed CP motor lead
- Vent valve system purges air from the sump drainer preventing pump air lock
- Flow rates available from 2 - 1,200 gpm
|
|
The U 3 K (S) is an extremely versatile submersible pump for stationary and portable use. EIP technology for safer operation, integrated flushing device for reducing deposits and integrated low level pumping for preventing flooding are only a few of the innovative features that set this pump apart.
- 10 mm free passage
- discharge branch 1¼"
- Hmax = 7 m
- Qmax = 6,5 m3/h
|
|
|
Sethco sump pumps are used for corrosive services; chemical processing, waste treatment, acids and alkalies, chromic acid wastes, salt water, and fume scrubbers.
|
|
|
|
Vertical pumps
