|
|
The DONADON “PS” panel is a composite, tension panel.
It is composed of two parts:
· An incised metal section
· A PTFE membrane.
Suitable for use with gas in static, pulsating and cyclic conditions. PS vent panels are available in square, rectangular or circular models.
They usually have very low vent or vacuum pressures.
These panels are mainly fitted to dust manifolds, dryers, troughs, silos, separators, mixers, boosters, air filters and sieves.
They can be fitted between welded frames or non-machined profiles in carbon or stainless steel.
Machined frames or expensive holders are not necessary.
TRIGGER SPEED: The PS panel responds well to excessive pressure and vacuum.
OPERATING MARGIN:
- flat panel: the PS has an average ratio of 50% between operating and venting pressure
- pre-shaped panel: the PS has a good ratio of 70% between operating and venting pressure
FRAGMENTATION: No fragmentation
VACUUM: A vacuum support is recommended.
Venting pressure from 0.07 to 0.65 Bar at 22°C
Venting temperature up to 50°C
Tolerances on venting value:
- for venting values below 0.1 BAR: ± 20%.
- for venting values between 0,1 and 0,65 BAR: ± 10%.
Seal materials:
- up to 120°C. Neoprene
- from 121 to 230°C. Silicone
- Other materials on request
|
|
Explosion venting is one of the most common and effective forms of passive explosion protection. Explosion venting provides overpressure protection from potential industrial explosion hazards by providing a planned pathway for the expanding gases to escape. Damage to industrial equipment subjected to explosions can be controlled through use of explosion venting.
Fike, a pioneer in the development of explosion venting, continues to lead the way by producing an unsurpassed range of Atex certified explosion venting solutions for all areas of industrial activity. Virtually maintenance free and offering a long service life, Fike explosion vents are an ideal solution for many applications. |
|
| STIF launch a new product : explosion vent panels VIGILEX. Answer at Atex norms, STIF guarantee you advantages if your silo have a high pression. Its caracteristic are : Burst at 100 mbar, non adhesive food-grade seals, patented systeme, supplied with an inspection bureau test certificate, without added flange .You can,in option, equip his with or without alarm signal, a safety grille, a sealed telescopic conduit to allow release to atmosphere for equipment located inside buildings and a thermal isolation. |
|
| AP&T´s niche tools and production solutions are available in product areas like deep drawing, fire extinguishers, heat exchangers, air duct parts, pressure vessels and filter housings. We manufacture press lines for producing fire extinguisher shells in sizes from 1 to 12 kg and blank thickness from approx 1,4 to 2,5 mm. |
|
When economy and performance are equally important, select from the SENTRY line of stored pressure, hand portable fire extinguishers. Designed for light to medium use, SENTRY extinguishers are available with dry chemical, carbon dioxide, or water.
Typical applications... Auto repair shops, banks, electrical equipment rooms, hotels, machining operations, material handling vehicles, offices, schools, warehouses, and others. |
|
| Stoelting's OmniJet-218 Aqueous Cleaning System features all stainless steel (polished) construction, sustained high solution and dryer heat capability, high volume “EDM” spray bar for greater GPM concentration per square inch, convection-type dryer with adjustable blow-off knives that produce high velocity water strip action, for board and component (flip chip, BGA,) cleaning. |
|
very resistant non slip covering adapted for safety, installation of signals, working aera, assembly lines, machine tool peripheries...
Non slip covering very comfortable and resistant for high traffic, anti-fatigue and anti-shock on industrial grounds.
Environment: In wet or dry conditions for free application. Chemical characteristic: Elastomeric polyurethane complex poured onto a polyester rotproof non-weaved undercoating. Thickness: 6.5mm Granule: Non abrasive flexible granules 800µ Weight: 7kg/sqm Skidding conditions: Measurement of roughness of the surface on RRL pendulum according to road non slip standards for pedestrian ways NFT 98609-1 (scale from 0 to 150). Test coming from laboratory of Ponts et chaussées from Angers.
Coefficient on dry ground : 90
Coefficient on wet ground : 55
Resistance: Very good resistance to U.V, (7 on the scale of the blue textiles rated from 1 to 7). Very good resistance to natural chemical agents, oils, grease, hydrocarbons, salt water.
Excellent resistance to abrasion and shocks. Resistance to traction: 10daN/sqcm of tractive front. Resistance to temperature: from -30°C to +80°C.
Flexibility / Deformation: Elongation = 100% before breaking. Simple maintenance: Regular cleaning with water and household detergents. Inside factories and shops, the use of biodegradable detergents with a pH of 9 is recommended. |
|
Earth Testing covers the testing of earth electrodes and the measurement of soil resistivity. The instrument requirements depend on the range of applications.
|
|
| The ground resistance of substations can be measured with two auxiliary electrodes which are put into the ground. To avoid influences from the mains current and its harmonics, this measurement should preferably be carried out with 128 Hz.The high output power of the CPC 100 ensures a high ratio of the signal level to the noise level. Thanks to the signal processor technology, the measuring procedure is very selective and disturbances by ground currents are reduced to a minimum. |
|
Description:
Reads ground resistance down to 0.10Ohm.
- Fully autoranging with data hold to capture readings.
- Convenient alarm and 99-point memory functions.
- Measures up to 30A RMS ground or leakage current.
- Measures currents down to 1mA.
- Accessories included: (1) 9V battery, molded carrying case, test resistance loop. |
|
or a door
drive control system. A range of similar
equipment for potentially explosive
environments is also available.
Smoke and heat detectors
Dictator provides complete hold-open systems for fire protection doors that are normally kept open but that have to be closed reliably in case of a fire.
One component of the hold-open system are the tested and approved DICTATOR smoke and heat detectors. They provide reliable detection of smokeor temperature rise.
They are powered by DICTATOR power packs.
Also according to the ATEX 100 directive for the use in hazardous areas.
Further DICTATOR products for hold-open systems:
Electromagnets
Door operators for fire protection doors, also in ex-proof design
Furthermor DICTATOR furnishes a smoke alarm for private dwellings. |
|
A sealing hose system was developed in cooperation with the Industrial Fire Brigade of Henkel KGaA Düsseldorf. This system enables sealing of positions which are difficult to access and which have operating pressures of up to a maximum of 10 bar (145 psi).
There are two set variations supplied: Premium Set and Base Set. Both sets are contained in a practical transport case and are easy to use. |
|
Cable seal with progressive tighteninig
Description :
Resistance : diametre : 1,6 = 412Kgs - 2,4 = 850Kgs
Material :
Head : Zinc
Cable : Galvanized metal
Characteristics :
Consecutive numbers
Free marking from 500 pieces
Marking of 6 digits and 3 letters maximum
Cable length : 300mm
Diameter : 3.2mm, 2.4mm, 1.6mm
Options:
Colored Head
Laser marking and barecode
Cable length up to 2000mm
Delivery time:
Neutral model: available on stock
Personalized model: about 10 weeks
Customs tariff: 83 09 90 90 |
|
High security seal for container
Description
2 parts : the body and the nail
Diameter of the nail : 8.5mm ; Length of the nail : 75mm
Diameter of the body : 20mm ; Length of the body : 31mm
Material :
Nail cover with acrylonitril styren
Body make with acrylonitril styren
Characteristics:
Consecutive numbering ( max 7 letters )
Free marking from 5000 pieces
Certified ISO/PAS 17712
High security seals specification
Accepted by french, american, and english customs
Standard color :
Packaging :
250 pieces per box 10Kgs ; 38x26x16cm
Delivery time :
Available except personalized : about 6 to 8 weeks
Customs tariff : 83 01 10 00 |
|
At the very latest when, because of a power failure (intentional or not) or a malfunction something has to be done to safeguard man and machine, hydraulic clamp Ratio-Clamp® - the clamping device from Hänchen - is just what you need.
Boasting a retention force of up to 450 kN, the hydraulic clamp holds the piston rod in whatever position it is in at that particular moment. Without having to rustle up some extra power (no extra energy) and for an unlimited period of time. The clamping device Ratio-Clamp® is approved by the German Technical Inspection Agency (TÜV). Nor does the development of specific solutions (larger rod diameters, intermediate sizes, greater clamping forces…) pose a problem to the Hänchen specialists.
The possibilities for your application:
Rod-Ø from 10 - 140 mm,
clamping forces from
1 - 450 kN. Other
dimensions on request.
Other products of the range of services:
- Hydraulic cylinders
- Test cylinders
- Complete system solutions (Ratio-Drive®)
- Pressure intensifiers
- Industrial shock absorbers
- Special cylinders of all kinds
- Mounting parts/assembly utilities/accessories |
|
AE&T launches a new product for the protection of the people subjected to shocks and wounds on their workplace: It concerns the square corners, cutting edges, corners, IPN beams, pipes...
These shock absorbers called AMORTIFLEX®, are made of a hard resistant thermoplastic (polyethylene) for severe industrial use.
"A small shock absorber is better than a great shock" such is the aim of this safety product, original, flexible and extremely useful.
The yellow and black colors draw the attention and prevent risk. The material protects from the shock. AE&T offers a wide range for various applications, with a big choice of different sizes and models.
Samples are proposed to test the product on site. Let us wish your readers a good discovery of the Amortiflex® shock absorbers!
|
|
Park Sentry™ is a simple method to add a layer of scratch-free impact resistant material around a square or rectangular column. Its slim design adds protection without adding bulk to the column. Parking structures using Park Sentry can virtually add space by inviting closer contact between vehicles and columns without the fear of scratches or dents.
Park Sentry is molded of proprietary ARPRO® material ready to be installed around the column without tools. Park Sentry is a modular product: separate corner and plank products combine to surround the column with protection. A key-lock system positions the pieces correctly and holds them together. A set of reflective polypropylene straps surrounds the entire installation, holding it firmly to the column and providing a highly visible contrasting element visible in dimly lit buildings or parking structures.
Park Sentry is 1 meter (approximately 40in.) high and can be configured to fit any sized column by adding or subtracting pieces or cutting to fit. It is available in either bright yellow or black with contrasting reflective straps. |
|
| Eliminate avoidable costly repairs to your building, stationary plant equipment and fixtures, in your warehouse and at your loading dock. |
|
These versatile inflatable air bags and stoppers are used to accommodate a wide variety of industrial applications.
Most commonly used for:
Plumbing operations
Ideal for creating an air-tight seal in drainage applications
Low pressure hydrostatic tests
On-site thermoforming of bends in ducting and conduit materials
Fibre-optic construction projects
Debris and Animal Stopping
Weld purging to isolate large volumes in tanks, so minimum volumes are left for argon/nitrogen purging
Features:
Inflatable air bags up to 2,000 mm (80") diameter
Manufactured using a high quality latex inner tube and polyurethane impregnated nylon fabric outer cover
Installed with a length of flexible inflation hose with sealing tap/valve.
Styles:
Cylindrical bags which do not 'turn over' in the pipe.
Spherical bags which are ideal to insert through a small hole + seal a large diameter pipe.
Rectangular stoppers for ducting.
Heat Protected Stoppers.
Concrete Pipe Test Stoppers.
All sorts of special shapes and sizes have been taken on as specials! |
|
An Expansion joint of rubber is a made flexible union with natural or synthetic elastómetros, weaves of reinforcement designed to compensate extensions and contractions by temperature variations, damping and absorption of vibrations in facilities of transmission of fluids.
The problems of vibration, noises, shock, corrosion and tensions can be solved early incorporating the Expansion joints of rubber in the systems of conduction of fluids. |
|
PRONAL inflatable stoppers are used:
- to test pipes for leaks under pressure
- to isolate pipes during maintenance operations
- to make temporary seals to avoid run off of toxic products.
Thanks to the materials employed and the suitability of their design, PRONAL inflatable stoppers are ideal for all types of pipes.
Advantages:
- simplicity and speed of installation,
- completely leakproof,
- safe to use,
- suitable for a wide variety of pipes : concrete, cast iron, steel, stainless steel, PVC,
- sturdy and long service life.
A highly diversified range of products :
- one of the widest range of products on the market,
- from standard to made-to-measure : models for low pressure and high pressure environments (over 100 bar depending on requirements)
- a choice of shapes : cylindrical, ovoid, square...
- no size limits : up to 3,000 mm in diameter,
- specific models which comply with particular specifications. |
|
Float-in Bags are fitted with a reinforced front cover and tension lugs. The CR material ensures increased resistance to chemicals. Working lines are secured to the tension lugs using carbine hooks and the pipe sealing bag can be floated into the pipeline without any difficulty.
Only four sizes are needed in order to seal pipe dimensions ranging from 70 mm to 1200 mm (2.8 inch to 47 inch). The float-in bag program is rounded off by a chemical variation in addition to the basic design.
In this case, all metal parts on the float-in bag are made of stainless steel and the integrated inflation hose (10 m/32 ft.) guarantees the corresponding safety distance to the area of danger. |
|
Bird Strike Problems ?
In collaboration with specialized ornithologists and France Civil Aviation Authority (DGAC), LORD has developed a unique bird control system based on green laser light. Harmless and nuisance free, this innovative bird repelling technique has proven unrivaled effectiveness for the two years of real-world testing on airports.
The handheld LEM50 laser torch and the automated TOM500 bird deterrent system are rapidly becoming THE determining complement to bird control programmes of most airports worldwide.
For more information and to view the list of our authorized distributors please go to our specific web site through the following link: http://www.tom500.eu |
|
- Features Fits Most Flashlights
- Maintenance Free, Easy Installation
- Low Power, High Intensity
- Sunlight Visible
- Solid-State, High Shock / Vibration Resistant
- Long Life: 50,00+Hours for White LEDs, 100,000+ Hours Other Colors.
- Colors Do Not Fade with Use
Applications
- Law Enforcement
- Pilots
- Astronomers
- Hunters, Campers
- Night-Vision Goggles and Cameras
Options
- Industry Standard Bases
- Special Voltages
- Flashing, Blinking |
|
Features
• Flashing LED for High Visibility
• Low Power Consumption
• Easy to Wear
• Extremely Light Weight
• Highly Reflective Stripe
• Exceptional Durability
• Ultra Bright LEDs
Applications
• Construction Workers
• Pedestrians, Joggers
• Police, Fire Departments
• Safety Workers
• Night Workers
• Nighttime Recreational Activities
• Parking / Valet Attendants |
|
The meter of loves at first sight makes it possible to enter the loves at first sight on a installationextérieure of protection (Prevectron, simple point, cage with a grid,...).
Its digital posting (6 digits) allows a direct and comfortable reading number of impacts entered. The recording of the loves at first sight and their memorizing nenécessite no external power and is thus depend on the lifespan of the pile.
Only the digital posting, ordered by a button in frontage, requires a food provided by a pile lithium long life.
|
|
The first self-testing obstacle warning light
The new range of TWINY obstacle warning lights is made of a master and a slave beacons. The "slave" is automatically working as soon as the "master" is down. This design is securing the obstacle beaconing, since the system will be permanently operational. The Twiny range also includes a dimmer switch which will automatically switch on and off the lights during day and night time.
Furthermore, the TWINY range has a unique and specific self testing device, working daily or on request according to customer specifications. The test procedure check the two beacons conditions. If ever one of the light test is negative, a defect contact will report the information. The testing procedure is visible from the ground (no need to reach the beacons to start or witness the test).
Three types of low intensity obstacle warning lights are available within the TWINY range: the BA10 incandescent lights, the LED BA15 lights as well as the Neon BA20 and BA30 types.
|
|
|
|
Other safety and signaling equipment
