|
|
| Products 121 to 150 of 317 |
A various and large high quality 2, 3, 5 ways manifolds range implemented by condensing pots in stainless steel.
A part of this range is available with Double block and bleed feature.
|
|
Internal or External Valve Body Manifold Stack Valves with Actuators
MANIFOLD DESIGN FEATURES:
- 3/4 to 1 1/2" full port stack valves
- Standard manifold stacks are 1 to 5 valves. Larger stacks can be custom built for special applications
- Max working pressure: 150 psi @ 70 F
- Ball and Stem: 316 SS
- Valve Body: Available in poly or nylon
- Seat: Virgin PTFE
- Stem Seal: Dual VITON O-rings
- Body Seal: EPDM
ACTUATOR FEATURES:
- High quality, durable actuator housing rated NEMA 6P for waterproof applications and NEMA 7D for Ignition Protection applications
- 12/24 VDC and 24 VAC operation
- Tough aluminum gear box with metal gears
- Waterproof wire plug connectors
- Private labeling available
Consult our Engineering or Sales staff for application assistance.
|
|
Manifolds from one way and two valves to two ways and five valves. With several configurations for direct connection to transmitter or through threaded connections.
Pressure interval: 420 bar
Temperature interval: -20ºC / 200ºC
Made in several alloys.
|
|
|
These calibration manifolds are having one isolating valve of 1/2" connection & one dain valve of 1/4" NPTF out let which can be used for calibration. Compcat unit saves space, reduces number of joints resulting in cost reduction. Used with pressure gauges, pressure switches & transmitters. Different options as shown below are available.
|
|
|
'PRIME' make manifold valves are installed to control, measure, isolate, equalize, calibrate, drain, vent or differentiate the pressure of liquids and gases. They are manufactured to precise dimensional tolerance to ensure perfect installation and application. We offer 2,3,5 valve manifold configuring remote mounting type (pipe to pipe), direct mounting type (pipe to flange 'T' type and flange to flange 'H' type) or panel mounting type on to gauges, DP transmitter and pressure switches with 2 1/8” (54mm) center.
|
|
BULK Instrument Manifold are manufactured in 316 stainless steel or in any machinable metals including: Carbon Steel, Monel, Inconel Titanium, Hastelloy C.
To conform with H2S Sour Gas service requirements, BULK Instrument Manifold can be manufactured in accordance with NACE specification MR-01-75.
QUALITY CONTROL TESTING & CERTIFICATION
Ensuring quality is one of the more important considerations in the production process at BULK.
It is not only inspected the final product but all the stage manufacturing steps are surveyed in detail.
Production of all components is carefully controlled from design through final testing.
Records are maintained to verify specification compliance in raw material procurement and testing.
Following are the inspection documents available upon request:
Certificate of Compliance with the order
Test Report
Inspection certificate
Each valve is hydrostatically tested prior to shipment.
|
|
Manifolds 2, 3 or 5 ways AMFD
Fields:
- Pharmaceutical and Biotechnical Industry
- Heating
- Ventilation and Air Conditioning
- Machine and Process Industry
- Power Plants and Distribution
- Automotive Industry
Type: AMFD
Differential pressure gauge NS 100 and 160
Fields:
- Pharmaceutical and Biotechnical Industry
- Heating
- Ventilation and Air Conditioning
- Machine and Process Industry
- Power Plants and Distribution
- Automotive Industry
Type DMD-DMDE-DMDG101-161
Application: Chemical industry, plant engineering, energy engineering, food industry, medical technology
|
|
Manifolds
Delta Controls has expanded its process control instrumentation portfolio by introducing a complementary range of valves and manifolds. Ideal for use in conjunction with Delta's pressure and temperature switches or pressure transmitters, these robust accessories are the perfect solution for even the most demanding applications.
|
|
Integrated Fluidic Platforms
When designing a custom fluid circuit, utilizing a precision drilled or bonded laminated plastic manifold offers advantages over traditional methods such as tubing and fittings. The advantages of state-of-the-art integrated fluid circuits is the elimination of entangled tubing paths and possible leak points. A fluid circuit design can incorporate extraordinarily small fluid channels (less than .020" cross section), and because we can use several layers of plastic, multi-layer fluid paths can overlap each other. A circuit can incorporate valves, pumps, check-valves, liquid chambers, and filters.
|
|
1/4" Plug - 3 pcs
1/4" Barb Fitting - 1 pc
|
|
1/4" T Fittings-3 pcs
1/4" Elbow Fitting-1 pc
1/4" Man. Bracke -1 pc
Mounting Screws-3 pcs
|
|
Parker’s RM02 Liquid Line Manifolds help optimize coil efficiency, thus decreasing coil and overall unit size. The manifolds are used on slab coils, A-coils, condenser coils, package air-conditioning units and package heat-pump units. Different orifice restrictors can be installed in each leg to balance coils.
* Fixed restrictors for air-conditioning systems or cartridge restrictors for heat pumps are available in the legs of the liquid line manifold.
* Orifice sizes of the restrictor are clearly stenciled on the manifold legs for easy identification.
* Manifold assemblies can be 100% helium-tested by Parker for flow and leakage to ensure quality and proper restrictor sizes in each leg.
|
|
REFRIGERANT INDUSTRIAL MANIFOLD
Type M Dual Stop Valve Manifolds allow for two relief valves to be mounted. This arrangement permits either valve to be shut off individually and removed for repairs or inspection. Thus, one valve is always in service as required by most codes
|
|
ARI-CODI S
Application: Collects and distributes condensate, steam and fluids
Medium: Steam, condensate, water, oil, etc.
|
|
Features
* No packing to maintain, ever
* Same face-to-face as gate, plug or ball valves to 12”
* Sleeve is the only wetted part
* Position indicator, heavy-duty sleeve
* 100% full port design
* Bi-directional bubbletight shutoff
Materials of Construction
* Cast iron or aluminum body
* Heavy-duty carbon steel mechanism or optional stainless steel, position indicator, brass bushing, and grease fittings
* ANSI Class 125/150 flanges or metric flanges
* Available Elastomers
The Series 75 manually operated pinch valve is the number-one selling pinch valve in the world today. The Series 75 is a reliable, maintenance-free, cost-effective valve designed for tough slurries, abrasives, and corrosive-chemical applications. The Series 75 full port design eliminates any dead spots or crevices, seats or bearings where slurry can hang up and impair operation or even cause complete valve failure.
|
|
The 710PTNM is engineered for precise dispensing of semi-viscous liquids including metered and mixed two-part component fluids and volatile cyanoacrylates. The only part of the pinch tube valve making contact with the fluid being dispensed is the disposable pinch tube assembly.
Features
• Disposable pinch tubes minimize maintenance
• Designed for low viscosity fluids
• Ideal for two-part epoxies and cyanoacrylates
|
|
The UPM pump by BELL is the right choice to operate continously or alternately single and double acting cylinders.
It is equipped with a retained control to work in standby for the pressurization of the circuit. The hand valve is a 4 way - 3 positions with open centre and standard CETOP 3 connection.
|
|
MANUAL VALVE "Y" TYPE
Two way interception/control manual valve with slanting seat. Solid and compact shape with low loss of load and maximum hydraulic efficiency.
Suitable to intercept: steam, water, corrosive fluids, no-explosive gas, etc.
- Material: STAINLESS STEEL AISI 316/316L (1.4408/1.4409);
- Seal body gasket: CARBOFIBER, PTFE;
- Linear and rapid opening plug: AISI 316L WITH PTFE - PTFE/CG;
- Packing box: PTFE RING ENERGIZED WITH OR VITON;
- Sizes: 1/4"-2", DN15-100
- Rating: PN16/25
- Working temperature: -60°C/+180°C.
|
|
Manual valves for manual shut-off, for gas, air and water, EC type tested and certified.
DN: 6 to 250,
connection: thread or flange,
pe: max. 4, 5 or 16 bar,
brass, steel or ductile cast iron housing.
|
|
Users of manually operated valves can rely on a full complement in Waukesha Cherry-Burrell's line. Available in 304 or 316L stainless steel; 1" through 4" tube sizes as well as fractional sizes. Pneumatic actuation optional on some models.
Valve Models Include:
- Ball
- Butterfly
- Check
- Compression
- Plug
- Relief
- Sampling
|
|
High capacity in open position and low cost. SOMAS manual valves fulfill these requrements, and we have a number of valves in our product line suitable for use as manual valves. The SOMAS full-flow ball valve SKV achieves very low flow resistance in the open position and is therefore an excellent choice for use as a manually operated valve.
SOMAS butterfly valves have, due to their robust, maintenance-free construction and comparatively low price also become a good alternative for use as manual valves.
|
|
|
|
|
|
SERIES 730 MASS FLOW CONTROL VALVES
The Series 730 Mass Flow Control Valves were designed by Dr. Jerry Kurz in about 1980 to provide a simple, compact electrically operated, precise metering valve for applications requiring a high flow rate turn-down ratio. The unique Kurz design utilizes a rotor having a helical shape machined into its bottom face, opposite an inlet orifice and an outlet orifice. The diameter, separation and the helical depth were designed to provide a nearly linear flow coefficient (Cv) with angular rotation. A simple high torque gearmotor (24 VDC) was selected for cost and simplicity. Since the Series 730 is a "fail-as-is" design, the motor is only used when changes are required, which greatly extends the motor life. The Series 730 combines the electric drive motor, the valve body, rotor and limit switches into a well-designed, integrated package. The typical turn-down ratio is 50:1, due to the incorporation of a pressure assisted shut-off disk which becomes active near the shut-off position. The Cv range is from 0.05 to 10.0 in three convenient body sizes. The Series 730 is constructed of 316L stainless steel, with Viton O'Rings and an o'ring sealed motor cover. It operates as a two-wire loop-powered device normally powered and controlled by one of the Series 155 Mass Flow Computers and used with a Kurz In-Line Mass Flow Element. The inlet and outlet fittings are Schedule 40 pipe with MNPT end connections or Class 150 flanges. Because of its rotary design, the Series 730 is not as affected by abrupt line pressure changes as are pneumatic control valves
|
|
|
Model VCD 1000 Variable Constant Differential Flow Controller is designed to control low gas flows at constant mass flow rates regardless of downstream pressure fluctuations. The Model VCD 1000 design yields extremely linear flow output in relation to adjusting stem rotation while offering bubble-tight shut-off.
|
|
The valve solution for abrasive, corrosive and fibrous products like granulates, powders and slurries.
Valve function :
The manual valve is closing with handwheel.
The pneumatic valve is normally spring closed, air to open.
Advantages :
Free passage, hermetic closing, safety function in the event of loss of energy/air (PA/PA2).
|
|
- Size Range: 15 - 50 mm
- Service Operation: Diversion, Mixing, Blending
- Materials: Stainless Steel, Carbon Steel
- End Connections: Screwed, Buttweld, Socket weld, Sanitary and others
- Service Application: Water, Oil, Steam, Gas, Thermal Fluid, Chemicals and others
- Temperatures: -30°C to 300°C
- Operation: Manual or Actuated
|
|
A Multiport selector manifold is a multiport valve that is used to replace traditional production and test oil field manifolds. It is sometimes called a ManiFlow diverter valve (MDV).
This valve replaces multiple valves and extensive piping in oil field applications and as a result significantly reduces operating costs.
The SchuF MDV has up to eight inlets, a test outlet and one main or production outlet. Typical sizes are from 1 inch (DN25) to 12 inches (DN300) and up to ASME 900 pressure class.
|
|
|
SchuF designs and manufactures a range of standard and special diverter valves. Many of our multiport diverter valves are exclusive designs for critical processes and often for severe applications. They are widely used in the PTA, Petrochemical, Polymer & Plastics, as well as Refinery industries.
|
|
|
|
|
|
The M-Diverter valve is used especially as a distributor of bulk materials.
The geometric design of the plug enables application in any conveying direction diverting or merging of the material flow from four lines to one or reversible.
Design characteristics
- suitable for pneumatic dense- and dilute-phase conveying systems
- smooth and gap-free transition due to patented design of inlet and outlet
- single channel design avoids plugging
- high dust and pressure tightness due to sealing pressing against the housing
- pressure tight from -1.0 to +6.0 bar (g) gauge to the outside and the non activated leg
- high reliability based on maintenance-free actuator solid temperature range from -20 to +120°C and ambient temperature range -20 to +40°C for standard design
- no additional safety device necessary as there are no moving parts outside the valve
- easy installation in all orientations because of integrated cast flanges and supports
- flanges easy accessible; no special connections required
- easily visible direction indicator of plug orientation
- direct control of plug orientation by proximity switches
- all bolts in stainless steel
- low total weight
- standard design with electrical connections in IP 65
- defection angle 4 x 45°
|
|
Silo(Redler)-outlet-gates, electrically operated including worm-gear-motor, 230/400 V, 50 Hz, and 2 mechanical limit-switches.
Slide plate runs on ball bearings in a U-frame.
Material: primed steel.
Product-contacting parts made of stainless steel on request.
ATEX version according to category 2 or 3 with admissible Zone 20 in the slide plate on request.
Application: Shutting off of bulk goods without over-pressure.
|
|
|
|
Other valves 
