|
|
The Flowserve McCannaseal is the original patented Top-Entry, Wedge-Seated ball valve. Available in regular port sizes from 1/2" through 20" and in FULL port sizes from 1" through 16" and pressure classes 150 through 1500.
The McCannaseal reputation for consistent, reliable operation in handling today's most volatile applications is known the world over and is featured on most ''approved'' lists for all types of processes.
Available with standard bonnet or with extended bonnet for cryogenic or high-temperature service. Wide range of body alloys and broad selection of seat and seal materials.
Features
* Top Entry-Inline serviceable
* Wedge Seats. Spring-loaded, self adjusting
* Back-seated conical stem seals. Blowout proof, seals tighter at higher pressure.
* Bi-Directional
* Polymer, metal, or ceramic seats available
* Flanged, threaded, and weld-end bodies
|
|
|
|
|
|
Applications: Acid Transfer, Beverage Processing, Brine, Brine Treatment, Chemical Processing, Chemical Transfer, Condensate, CO2 Injection, Flue Gas Desulphurization, Fly Ash, Fuel, Gas Production, Gas Scrubbing, Hydrogen, Lime Circulation, Lubricating Oil, Mineral Processing, Mine Dewatering, Oil Production, Oil Transportation, Organic Chemicals, Petroleum Production and Refining, Gasoline, Petroleum Distribution, Sea Water, Sewage, Waste Water
Industries: Acid Transfer, Condensate Systems, Chemical and Liquor, Crude Handling and Treatment, Gas Treatment, Miscellaneous Services, General Industries, Heavy Oil and Upgrading, Waste Processing, Water Handling and Treatment
Standards: ASME (ANSI), ISO
Misc:
Flowserve McCANNA Diaphragm valves provide leak-tight shut-off of corrosive liquids, semi-solids, slurries, gases, viscous materials and other fluids with temperatures to 400°F and pressures up to 200 psig. Available from 1/2" to 12" with a wide range of diaphragm materials.
Features
Long trouble free operation
Lower initial cost
Lower operating cost
Lower maintenance cost
Lower replacement cost
Lower inventory cost
|
|
High Purity diaphragm valves in PFA-HP, PVDF-HP and PP
Cleanroom manufactured High Purity valves for microelectronics, semiconductor production, solar industry and opto-electronic production
DN 6 - 100; valve bodies in ultra-pure plastic materials (PFA-HP, PVDF-HP and natural PP), own cleanroom production in Switzerland, manual, pneumatic and motorized operators, FlareStar PFA-HP fittings, HydraLine pressure measurement devices, TubeStar PFA-HP tubing, SonicLine PFA-HP ultrasonic flowmeter, variable area flowmeters in PVDF-HP
|
|
Features
High cycle double piston stainless steel actuator
Compact design, the outside diameter of the actuator is of the same size as the bonnet flange connecting diaphragm and body
Advantages in multiport bodies and manifold valve assemblies
Control air connection on the top, away from the process product line
Direction of control air connection is mountable in 90° rotations
Circumferential, defined sealing angle between process diaphragm and valve body
Flexible diaphragm suspension
Encapsulated diaphragm
Clean and polished exterior design ideal for sterile wash downs
Optional
Available with a wide range of control equipment and accessories, also for retrofitting
Autoclavable
|
|
|
|
|
|
The PV-12 Pneumatic Diaphragm Valve is designed for use in high purity semiconductor applications, and is also ideally suited for ultra-pure water and aggressive chemical or gas applications. The design utilizes a molded high purity PFA body with precision machined seat and diaphragm sealing areas. A one piece machined modified PTFE diaphragm is also utilized for excellent flexibility and life. A full 1" orifice provides maximum flow capability in a compact package.
FEATURES:
* Precision machined diaphragm manufactured from the latest technology modified PTFE. Provides over five times the flexural life as compared to conventional PTFE. Tongue and groove seal for positive diaphragm to body seal. Benefits are high cycle life, lower replacement costs and less downtime.
* PVDF coated stainless steel spring reduces effects of corrosive environments.
* Submergible option isolates all valve components from the external environment, which allows valve to remain functional while operating in wet or gaseous corrosive environments.
|
|
|
|
|
|
Model SS (Request form #VSS)
Up to 9 gpm, 3000 psi, ductile iron body
Series operation
Single unit or multi-function operation with stackable capabilities
Excellent spool metering, low leakage, manual and float detents available.
Model AD (Request form #VAD2)
15 gpm, 3000 psi, 1 or 2 spool model with intergral relief and loadchecks.
Excellent metering, low leakage.
Variety of spool types and actuator options
Power beyond and closed center available
Model BA (Request form #VBA1)
1, 2 or 3 spool valve, 30 gpm, 2500 psi.
Excellent metering, integral differential poppet-type relief and load checks.
Variety of spool types and actuator option.
Power beyond and closed center available.
Model BC
Single spool, manually adjustable, built-in pressure compensated priority type flow control
Characteristics and options similar to BA except open center only.
C Series (Request form #VCA1)
1 or 2 spools, 30 gpm, built-in relief, pressure balanced hard chrome spools are select fit honed..
Available in 3-way and 4-way configurations, open or closed center, variety of detent options
Model CA - manual version, spring centered
Model CD - automatic pressure kickout version
Model CS - solenoid operated version
Converta (Request form #VCV9)
Single spool standard model, open center only
Simple field conversion from 4-way to 3-way as well as spring centered to manual detent.
|
|
|
Global Manufacturer of the "Direc-Trol" line of manual rotary valves and the "Marstan" Solenoid or Manual operated pressure loaded face seal valve. Operating pressures available to 10,000 psi, with Horizontal, Vertical or Manifold mounting options and many different flow patterns to choose from.
|
|
MODELS : V4D01,V4D02,V3D06(Subplate Mounting)
SIZES - 1/4 " TO 3/4"
Max Pressure: 500 psi(350 bar)
FLOWS : 24 - 132 gpm / 90 - 500lpm
|
|
Disc Bottom Outlet Valves are widely used in the Chemical, Petrochemical, Pharmaceutical and related industries. They are used to drain vessels, tanks and pipelines. Invented by SchuF in 1923, they are today available as a disc rising and disc lowering variants. Disc valves have a shorter lenght than Piston or Ram valves and are therefore ideal where space is limited or weight is a concern.
SchuF Disc Bottom Outlet valves are available with many options including:
Dead space free fitting, Crust breaking, Disk grinding, CIP - clean in place, GMP, integrated sampling and flushing, fire safe and many different types of materials and sealing arrangements.
Disc Bottom Outlet valves are available from 1" to 18" as standard with 54°, 60° or 90° outlet angle.
|
|
|
|
|
|
Whatever you want from a Bulk Materials cut-off valve you’ve got it with Clyde Materials unbeatable Dome Valve® - the cost effective valve solution.
The Clyde Dome Valve®, widely regarded as the original and best material handling valve in the world, offers exceptional life from only a single moving part. The Dome Valve® is recognised as a low maintenance, long life solution that can last at least 1 million cycles between maintenance inspections. It has the ability to cut through static or moving columns of material and is pressure-tight, ensuring a consistent pressure tight seal is created when the valve is in the closed position, but in the open position it provides an unrestricted full bore opening for the best product flow characteristics possible. The Dome Valve® can also be used as a line, vessel or reactor isolation valve.
The Dome Valve® enhances other technologies from Clyde Materials Handling, a leading provider of pneumatic injection, conveying, materials handling & vacuum cleaning solutions.
The solutions we create for our customers generate many benefits and are backed by three decades of domain knowledge, expertise and a track record of generating exemplary success.
Dome Valve® sold in the United States under the trade name ‘Spheri Valve’
|
|
Plug type diverter
- Pressure shock résistant up to 10 bar*
- Two channel design
- Minimal maintenance
- Quick clean version available
- Compact form
- User friendly design
- Nomoving parts on the outside
- Pressure up to 3 bar g with static seals
- Sizes 50-150 up to 6 bar g with inflatable seals
|
|
3-way Poly Diverter KZValve, Side Load with KZCO EH3 low voltage actuator
VALVE FEATURES:
- 3-way Side Load Diverter valves available in 3/4" to 1 1/2" FP with threaded outlets
- Threaded or QHP hairpin connections available
- 150 PSI MAX (poly valve)
- 300 PSI MAX (nylon valve)
- 21 GPM @ 1CV
- Ball and Stem: 316 SS
- Valve body available in POLY or NYLON
- Seat: Virgin PTFE
- Stem Seal: Dual VITON O-Ring
- Body Seals: EPDM
ACTUATOR FEATURES:
- High quality, durable actuator housing rated NEMA 6P for waterproof applications and NEMA 7D for Ignition Protection applications
- 12/24 VDC and 24 VAC operation
- Tough aluminum gear box with metal gears
- Actuator housing available with "indicator flag" or with "blank" lid
- Waterproof wire plug connectors
- Private labeling available
Consult our Engineering or Sales staff for application assistance.
|
|
|
DP Plug Diverters are used on all types of pneumatic systems because of their simplicity and reliability. The machined plug with a bored "Y" through the center rotates in the machined body to divert flow. On-the-fly diverting is possible under many conditions. Available in sizes from 3" to 12" in cast iron, cast aluminum or cast stainless steel.
|
|
Diverter Valves - Conveying Diverters
Designed to meet the pneumatic conveying industry's requirement to re-route powder, pellets or granules from discharge points to another with minimal pressure drop and high sealing efficiencies.
Rotolok manufacture a full range of Flap, Plug and Weigh Diverters, which cover all applications in the pneumatic conveying industry to re-route powder, pellets or granules from one discharge to another.
For standard two way diversion applications, Rotolok specify the Flap Type Diverter Valve Range.
|
|
|
Gericke offers a comprehensive range of different diverter valves for pneumatic conveying systems. Starting with simple flat diverter valves, Gericke offers for dense phase conveying systems plug diverter valves and for hygienic applications pipe selector diverter valves type PS. The PS valve is suitable for a wide range of materials and all types of pneumatic conveying systems up to 4 barg. FDA approved materials to meet stringent hygiene requirements. Fast clean version to allow frequent and safe disassembly, gas tight seal which remain inflated even during change along. This valve is suitable for both diverting and converting modes.
|
|
90° Diverter
Series 229 & 237
Compact, Abrasion Resistant
The Dynamic Air 90° Diverter is a reliable, low cost, compact and simple design of heavy duty construction. A positive rubber-to-rubber seal is created by the internal flapper which presses against the unused port. The seal improves as the conveying pressure increases, ensuring better performance against leakage in even the most severe dry bulk solids applications.
Features
Abrasion resistant
Positive sealing to 100 PSIG
Full port design
Economical
Compact, low profile
Low maintenance
Position sensors standard
|
|
Fills hoppers via cyclonic separation in the inlet load tube and
exhausting air in the outlet tube.
Valves can be stacked on top of each other allowing multiple sources to multiple hoppers.
Standard Features
- Stainless steel material contact points.
- Lightweight aluminum frame, corrosion resistant.
- Positive blade lock (PBL) between blade and cylinder rod.
- Active compression seals (ACS).
- Internal magnetic piston cushioned air cylinder.
- Stacking design for multiple conveying lines.
- Rated for 82oC (180oF).
|
|
Features:
- Seal rings at each port
- Full round port pass way design
- Heavy duty body design for pressure surges up to 90psi (6.0bar)
- Manual or pneumatic operated
- Heavy duty pneumatic actuator with integrated mechanical stops
Application:
- Suitable for granular and pellets
- For distributing or merging of product flow
- For differential pressure up to 60psi ( 4.0 bar)
|
|
|
|
|
|
The V-Diverter valve is used especially for diverting the bulk material flow in pneumatic dense- and dilutephase conveying systems.
The patented design of the plug enables application in any conveying direction.
Design characteristics
- suitable for pneumatic dense- and dilute-phase conveying systems
- smooth and gap-free transition due to patented design of inlet and outlet
- single channel design avoids plugging
- high dust and pressure tightness due to sealing pressing against the housing
- pressure tight from -1.0 to +6.0 bar (g) gauge to the outside and the non activated leg
- high reliability based on maintenance-free actuator
- solid temperature range from -20 to +120°C and ambient temperature range -20 to +40°C for standard design
- no additional safety device necessary as there are no moving parts outside the valve
- easy installation in all orientations because of integrated cast flanges and supports
- easy subsequent change of complete drive from left to right side of diverter valve
- easily visible direction indicator of plug orientation
- direct control of plug orientation by proximity switches
- all bolts in stainless steel
- low total weight
- defection angle 45°
|
|
Bulk flow has to be distributed an collected. For that diverter valves with the highest demand on functionality and operational safety are used. For product pureness deposit-free and CIP capable diverter valves are indispensable.
Their maintenance-free operation is a deciding factor for the profitability of the plant. Diverter valves from Coperion Waeschle fulfil these numerous requirements even at high pressure and temperature ranges.
|
|
|
Twin-Outlet Diverting Rotary Valve combines the function of a rotary feeder/airlock and diverter valve in one simple mechanism. Select left or right discharge by changing rotor direction via motor and reversing switch. Only one moving part. Very compact. Exclusive tapered rotor allows rotor gap to be easily adjusted. Heavy cast aluminum, iron or stainless steel valve body. Adjustable packing gland shaft seals -- purge available. Heavy duty permanently sealed outboard roller bearings. Ideal for vacuum or pressure conveying systems. Available in five sizes with capacities up to 2,500 cubic feet per hour.
|
|
Size Range ...................... 1/2 "- 4" (DN15 - DN100)
Design ............................. Single Body Construction (SBC) with reduced number of body seals
Service ............................ Gas, Steam, Chemicals
Pressure Range ............ ANSI Class 150 to 1500
Temperature Range ..... -40°C to 250°C (-40°F to 480°F)
Materials ......................... Carbon Steel, Stainless Steel and Exotic Alloys
End Connections............ Screwed, Socket & Butt weld, Flanged & RTJ
Standards........................ Firesafe to API 607 4th Edt. and BS 6755 Pt 2
Operation ........................ Manual, Actuated and Coupled Actuation
|
|
TYPE SLEEVE, LUBRICANT, DOUBLE BLOCK, ECCENTRIC, FULL LINING (PFA,
FEP)
SIZE RANGE 1/4” TO 24”
BONNET TYPE TOP ENTRY, BOTTOM ENTRY
MATERIAL WCB, CF8, CF3, CF8M, CF3M, CF8C, CF10, DUPLEX, INCONEL, MONEL,
HASTELLOY…etc
PRESSURE RANGE CL 150 TO 2500
ENDS SCREW, SOCKET WELD, BUTT WELD
FLANGE: ANSI, JIS, DIN
OPERATOR LEVER, CHAIN LEVER, WARM GEAR, PNEUMATIC HYDRAULIC, MOTORIZE
|
|
Type:
DOUBLE BLOCK & BLEED split body
DOUBLE BLOCK & BLEED type ‘‘End entry’’
Design: B16-34 – API 6D
Nominal Sizes range: DN50 (2’’) to DN400 (16’’)
Pressure rating range: Class 150 to Class 2500
End connections: flanges, socket welding, Hub ends,…
|
|
|
W75 Series Double Seat Mix Proof Valves are easy to maintain with many safety features. They feature a robust, machine-from-bar design. Their Radial seal design minimizes leakage during transition. Available with reliable full-featured control tops. Independent seat-lifting options. Both stems detectable.
|
|
|
VARIVENT® double-seal valves type C have a one-part valve disk with a double seal. They are used for mixproof separation of incompatible media at flow path intersections within the pipe system. Double seal valves are the economical alternative to the generally used double-seat valves. The valve`s isolation chamber is equipped with two rinsing valves which are provided for leakage detection and cleaning of the isolation chamber itself. It is possible to clean the isolation chamber both separately and during pipe cleaning.
|
|
|
|
|
|
Standard Filter Corporation now offers the finest Diaphragm Valves manufactured by Goyen! The valves are available in a wide range of configurations to suit a variety of reverse pulse filter designs. These sophisticated valves precisely control airflow through the filters for optimal cleaning. The range now includes the exciting 'next generation' Millennium series which sets a new standard in performance, design, ease of installation and maintenance economy. The range of Diaphragm valves includes:
3 Series Pulse Jet Valves
Superior performance, easy maintenance diaphragm valve available with threaded ports (T3 Series), dresser nut ports (DD3 Series) or flange and slide ports (FS3 Series). Outlet at 90 degrees to inlet.
T Series Pulse Jet Valves
High performance diaphragm valve with threaded ports. Available with integral pilot or as remotely piloted valve. Outlet at 90 degrees to inlet.
DD Series Pulse Jet Valves
High performance diaphragm valve with dresser nut ports. Available with integral pilot or as remotely piloted valve. Outlet at 90 degrees to inlet.
FS Series Pulse Jet Valves
Very high performance diaphragm valve with flanged inlet port and slide seal outlet port for easy valve installation and removal. Available with integral pilot or as remotely piloted valve. Outlet at 90 degrees to inlet.
|
|
|
U.S. Air Filtration can provide dust collector diaphragm valves in a range of configurations to suit all types of pulse jet cleaning baghouse designs. These sophisticated diaphragm valves utilize a flexible molded diaphragm to regulate airflow through the filters for optimal cleaning. The diaphragm valve creates a pulse of air that shakes through the bag, shaking off any dirt from the outside of the bag, cleaning the filter. U.S. Air Filtration can provide a replacement diaphragm valve for any dust collection application. Specifically, we stock and distribute Goyen Diaphragm Valves, Goyen Diaphragm Valve Repair Kits, Goyen Solenoid Valves
|
|
The Clippard's Electronic Valves combined with a serie of manifolds provide a complete system for efficient interface with electric and electronic circuits.
Lilke a mouse, these valves are quiet, quick, eats very little and are cute. Valves accept low voltage, low current signals, convert them into high pressure (100 psi/ 7 bar) pneumatic outputs. Optional low pressure/medium or high flow are available.
Clippard Minimatic electronic valves are precision-built 2- or 3-way control valves, utilizing a unique, patented, valving principle. There are no slidings parts. Complete poppet travel is a mere 0.007"(0.18mm). As a result, low power consuption and exceptionally long life are major benefits of this design.
The valves are very quiet in operation and also very cool. The valves' small size makes them well suited to a wide range of applications.
|
|
|
|
|
|
Product description
- Eaton's Ultronics ZTS16 control valve is an integrated proportional valve package that delivers flexible machine functionality and advanced control options for many applications in mobile hydraulic machinery.
- The valve features a J1939 or CANOpen CAN interface for communicating application level machine control demands
- Each section contains two independent main spools (so called; twin spool) that are driven by an electronic pilot valve containing embedded on-board electronics and two proportional actuators. For full closed loop control, each main spool has its own LVDT position sensor and port pressure sensor.
- Ultronics ZTS16's open architecture allows users to develop their own application level programmes using Eaton's ControlF(x)™ applications development software and EFX controllers, or by using their own controller and associated software.
Benefits & Customer Values
- Greater efficiency
- Improved power management
- Better control
- Increased flexibility
- Reduced hose requirement
- Reduced inventory
- Software configurability
Specs
- Monoblock design available 1 to 6 sections
- System pressure rating of 300 bar per NPFA T2.6.1 (1 million cycles at 350 bar)
- Work section flow up to 130 l/min
- Ambient temperature: -40°C to 105°C
- J1939 or CANOpen communication input
|
|
|
|
Other valves 
