|
|
|
|
|
|
OLCOMPONENTS is the new product range launched by Olmark, that includes:
- BLOCK PIPE CLAMPS in polypropylene, polyammide or aluminium for single, twin or multiple pipes. Available series: Standard (rubber insert version also available) suitable for pipes with O.D. from 6 to 120 mm; Heavy (rubber insert version also available), suitable for pipes with O.D. from 6 to 168 mm; Twin, suitable for twin pipes with O.D. from 6 to 42 mm. All Olcomponents block pipe clamps can be equipped with cover and base plates, mouting rails and accessories for overlapped clamps.
- STEEL BALL VALVES wuitable for working pressures up to 500 bar, available in the following versions: two or three valves, flanged or MINI. Broad range of handles in zinc, stainless steel or aluminium, and in different shapes: straight, bent, short. Available diameters: from 1/8" to 1"1/4.
- QUICK-RELEASE COUPLINGS for all hydraulic applications at medium, high and very high pressure. Available series: ball valve, poppet valve, flat face and screw-on. Available materials (depending on the series): steel, stainless steel and brass.
All OLCOMPONENTS products meet most important international technical standards of the sector.
|
|
|
|
|
|
The use of under floor heating typically allows room temperatures to be reduced by 1°-2°C when compared with radiators, while still providing the same level of comfort. Each 1°C reduction in room temperature reduces fuel consumption by 6%. This means it is cheaper to run and gives the house a reduced carbon footprint.
As underfloor central heating is the enabler to maximise the use of low or zero carbon technologies for heat generation such as air source heat pumps or geothermal systems, it is key to sustainable indoor environments.
At Polypipe we manufacture the most complete range of floor heating systems for every application. Solid floor systems provide 'thermal mass' solutions and incorporate our unique floor panel, which enhances performance and requires less screed material than other systems.
The patented Overlay system provides a unique retro fit underfloor system, unlocking for the first time the massive potential for energy efficient under floor central heating in existing dwellings.
|
|
The range in PVDF comprises a complete series of pipes, fittings for heat socket fusion, manual and automatic valves for use in the construction of process lines and service lines to convey industrial fluids in the operating temperature range from - 40°C to 140°C.
The entire range is produced in SOLEF™ resins by SOLVAY S.A. classified according to ASTM D 3222 and compliant with requirements stated in ISO/WD 10931 for the use of PVDF pipeline systems in industrial processes.
|
|
We are a worldwide market leader for piping systems and components in plastic and complementary materials. The application-oriented system solutions and superior quality components are used for industrial applications, gas and water distribution, and building technology.
PVC-U
PVC-C
ABS
â-PP-H
PP-R
PE 100
PVDF
Pre-Insulated Fittings
Double Containment
Multilayer Fittings
PB
|
|
Nuflo and anti-syphon traps.
Manufactured in white polypropylene and Kite marked to British Standard 3942, the Nuflo range includes over 80 models.
Nuflo Traps are in 32mm and 40mm sizes and a wide variety of seal depths.
Nuflo’s Universal Compression Joints accept all plastic waste pipes and Imperial and metric Copper piping.
A range of Anti-Siphon Traps, True Metric Continental Traps, Space Saving Undersink Kits, Chromium Plated Bottle Traps and Condensation Traps further enhance the comprehensive range
|
|
ERIKS has an in-depth knowledge of
* process technology
* installation technology
* valve technology
Plastic valves
The combination of ERIKS’ knowledge of metal and plastic lined valves, and the behaviour of plastics has resulted in a unique plastic valve program to shoot the most critical applications. All remote operated valves are inhouse assembled and extensively tested.
Pipes and fittings materials
* PVC
* PVC-C
* PE
* PP
* ABS
* PVDF
* ATEX-comliant plastics
High purity
ERIKS offers a unique range of high-purity plastic piping and plastic valves, polished stainless steel diaphragm valves, ball valves and instrumentation.
* pharmaceuticals
* food
* fine chemicals
* cosmetics industry
* paper industry
* paint industry
* semiconductor industry
|
|
|
The FW pipe, a fiber reinforced plastic pipe consisting of FRP and resin mortar, is used for pipelines carrying agricultural or sewage water. Since FW pipes are strong and have excellent hydraulic characteristics, corrosion resistance, earthquake resistance, and workability, they are widely utilized in both new construction and renovating applications.
|
|
|
Pipes out of polyethylene may be applied across the range of high energy radiation. Pipes out of PE are well established for drainage of radioactive sewage water from laboratories arvj as cooling water piping systems for the nuclear energy industry. The usual radioactive sewage waters contain beta and gamma rays. PE piping systems do not become radioactive, even after many years of use. Also in environment of higher radio activity, pipes out of PE are not damaged if they are not exposed during their complete operation time to a larger, regularly spread radiation dose of < 10 i Gray.
|
|
|
|
|
|
MULTI-THERM™ 500 is the best prefabricated, preinsulated piping system for the distribution of low to high pressure steam, high temperature hot water and general fluid transportation systems. The design eliminates corrosion and reduces energy loss.
MULTI-THERM™ 500 is the best drainable, dryable and testable, prefabricated, preinsulated piping system for the distribution of low to super heated high pressure steam, high temperature hot water and general fluid transportation systems. The outer conduit is insulated with polyurethane foam insulation and has a jacket of filament wound fiberglass or extruded HDPE jacket. MULTI-THERM™ 500 is a smooth wall, spiral welded, 10 gauge steel conduit. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a Leak Detection and Location system.
- Temp Range: 250°F to 750°F (standard), above 750°F (special)
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
POLYTHERM® is the best system we offer. It is a fiberglass jacketed, polyurethane foam insulated piping system for above and belowground distribution of liquids from -320°F to 250°F.
POLYTHERM® is a fiberglass jacketed, spray applied polyurethane foam insulated piping system for above and below ground distribution of liquids from -320°F to 250°F. PERMA-PIPE's multi-directional filament winding process produces a high strength fiberglass reinforced polyester resin jacket over the insulation for maximum protection from the environment. This high-strength fiberglass jacket is applied to systems having an outside diameter as large as 48 inches. Electric heat tracing is an option with this system.
POLYTHERM®'s spray insulation process assures void-free insulation. By applying insulation before the jacket is applied, complete visual inspection of the insulation is performed. This process assures void-free insulation and therefore, maximum thermal efficiency to provide optimum performance of cryogenic and heat thermal distribution systems. The POLYTHERM® system is fully engineered to job specifications, thereby reducing field costs by providing custom made, factory-fabricated fittings which reduce the number of field connections as compared to the field kit method.
- Temp Range: -320ºF to 250ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter 1/ 2" - 36" (standard), Nom. Length 20' and 40'
|
|
POLYTHERM® is the best system we offer. It is a fiberglass jacketed, polyurethane foam insulated piping system for above and belowground distribution of liquids from -320°F to 250°F.
LO-TEMP - HI-GARD™, is a designed for the distribution of fluids aboveground at temperatures up to 250 ºF. Based on customers specifications, this is a prefabricated system with all fittings attached to straight sections.
ULTRA-NW™ is an advanced prefabricated, secondary containment piping system for hazardous chemicals, process waste and general fluid transportation. It is a fiberglass clad stainless steel conduit system with no need for cathodic protection.
|
|
|
This heat transport pipe consists of an inner pipe with a layer of thermal insulating material, and a reinforcing layer formed around the inner pipe. Responding to the need for transporting heated mediums such as steam, and heated or chilled water, this product has been developed and is contributing to the efficient use of energy. For example, heat transport pipes have been installed in area-wide air conditioning systems and other facilities that utilize excess and waste heat or geothermal energy.
|
|
|
|
|
|
ESCON-A®/ FERRO-SHIELD™ is the original prefabricated, preinsulated piping system for the distribution of low to high pressure steam, high temperature hot water, and general fluid transportation systems.
ESCON-A®/ FERRO-SHIELD™ is the original drainable, dryable and testable, prefabricated, preinsulated piping system for the distribution of low to super heated high pressure steam, high temperature hot water and general fluid transportation systems. The outer conduit is coated with our Elephant Hide urethane coating which provides an outstanding corrosion resistant covering. ESCON-A®/ FERRO-SHIELD™ is a smooth wall, spiral welded, 10 gauge steel conduit. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation, but we recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a Leak Detection and Location system, or Cathodic Protection (optional).
- Temp Range: 250°F to 750°F (standard), above 750°F (special)
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
ULTRA-HT™ is an advanced preinsulated secondary containment piping system for general fluid transportation that requires an insulated steel containment. No need for cathodic protection.
ULTRA-HT™ is the designed for maintaining fluid temperature while containing hazardous fluids. This system complies with Federal regulations for secondary containment of hazardous fluids, that require insulation to maintain their temperature. Drainable, dryable and testable, prefabricated this secondary contained piping system is designed for the distribution of jet fuel, radioactive waste, bio-process waste and chemical transfer. ULTRA-HT™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding .100 mils thick and designed to withstand a 35,000 volt holiday test. ULTRA-HT™ is supplied with stainless or other high alloy pipe and containment. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system and electric heat tracing.
- Temp Range: 32ºF to 750ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
PREMANT®
Ultramodern technology for efficient production
Our pipes are available in dimensions from DN 20 to DN 1000; the types of foam insulation, medium pipes and the system for the monitoring wires can be selected freely.
Thanks to our modern production facilities, we can react rapidly to your requirements.
|
|
MJ - Metal Tube Jacketed (Single Metal Tube)
Copper Tubes:
1/4” OD x .030” Wall
3/8” OD x .032” Wall
1/2” OD x .035” Wall
Welded Stainless Steel Tube:
1/4” OD x .035” Wall
3/8” OD x .035” Wall
1/2” OD x .035” Wall
|
|
Excellent Chemical Resistance and Long Service Lives
Optimum column lining materials for mass transfer processes involving corrosive media
Equipment lined with these two PTFE variants can meet nearly all customer requirements entailing special designs, large lining thicknesses, electrical conductivity, etc. in mass transfer processes involving highly corrosive media.
Vessels and process equipment can also be provided with these special PTFE linings.
LICUFLON® and POLYFLURON® columns are used mainly in the chemical and pharmaceutical industries.
|
|
PTFE lined pipes DIN 2848/2874 DN 15 DN 600 PN 10
Standard version: 1 fixed flages, 1 lap joint flange
Carbon steel Body
|
|
A large range of PTFE lined piping adn fittings that resist to corrosion and answering all your applications :
· PTFE lined elbow
· PTFE lined tee
· PTFE lined reduction flange
· PTFE lined cross
· PTFE lined instrument tee
· PTFE lined piping
· PFA check valves
ND 25 to ND 600.
From 100 to 8000 mm
Up to 230°C
Up to 25 bars
ASME/DIN
PTFE Antistatique (noir)
Heavy duty thickness
Vacuum designed application
|
|
- Universal corrosion resistance
- To feed gases and liquids into columns and vessels
- Temperature range: -10°C up to + 200°C
- In max. lengths of up to 6000 mm, depending on diameter
- In nominal diameters up to 600
- In flange dimensions according to DIN and ANSI
- As bent inlet pipes
- In variable versions allowing flexible adjustment of the dip length
|
|
Fluoropolymer Tubing
* Stock PTFE sizes from 4mm to 12mm OD
* Stock FEP sizes from 4mm to 12mm OD
* Suitable for food use
* Non hardening
* Non stick
* Durable
* Excellent chemical resistance
|
|
|
Enhance performance and product life by using the material best suited to YOUR application CoorsTek Materials Professionals help you choose from a multitude of advanced ceramics and high-performance plastics like Alumina, Zirconia, Silicon Carbide and others PTFE, UHMW.
|
|
- Product Code: PS1030
- Product Description: 225mm x 3m Polysewer Plain Ended Class 8
- Material: uPVC
- Length: 3
- Outside Diameter: 250
- Inside Diameter: 22
|
|
BRUGG-STAMANT®
Guaranteed environmental safety
BRUGG STAMANT Safety Pipe ® is a dual pipe system prefabricated in construction units; it is especially suitable as a pipe to transport combustible or non-combustible media and gases that endanger water.
Optical and acoustic alarms are triggered in case of a leak if the pipe is used in conjunction with a leakage indicator.
Conditions and requirements
Conventional engineering of dual-wall pipe systems to transport hazardous substances must meet the highest requirements in terms of expert design and optimal technology - especially when larger dimensions are involved. As you would expect, we guarantee compliance with all conditions for fire and explosion prevention and water protection.
|
|
OLMARK can boast years of experience in designing and manufacturing bended, assembled and flanged rigid pipes (in steel, stainless steel or copper) available in all possible dimensions and shapes required by clients’ technical specifications.
OLMARK’s pipes come, on request, with a CAD-3D drawing and they are all successfully tested in compliance with the most rigid international standardization directives.
With an outside rigid pipe diameter manufacture capacity that can spread from 4 to more than 300 mm, the range of personalised pipes designed by OLMARK is the natural choice of important OEMs, whose success depends on high working pressures control.
|
|
Material : St 52 bk + s, St 52.0
St 52-3N, StE 460 nbk ::Tol. OD DIN 2391; 2448
Tol. WD DIN 2391; 2448
Tol. ID ISO-Tolerance Field H8 - H11
Center Line Average of Interior Surface honed Ra max. 0,5 µm
roller burnished Ra max. 0,4 µm
Dimensional Range: ID ø20 - 500 mm, larger dimensions on request
|
|
Seamless tubes size range »
1.0mm (0.04") to 50.8mm (2") OD. Straight lengths up to 16m (51ft), seamless coiled tubing 6.35mm (1/4") thru to 25.4mm (1") OD.
Our product range consists of straight and coiled tubing. These tubes can be either seamless, welded or welded and drawn.
|
|
Standard：
API SPEC 5CT Standard of American Petroleum Institute
Application：
Seamless steel tubes for oil casing and tubing in oil wells
Model N0．of steel tubes：
J55，N80，L80，P110 etc．
|
|
We can makes and markets cold-drawn and hot rolled seamless steel pipes and cold-drawn special-section seamless pipes which are widely applied in the industries of petrochemical, boiler, automobile, mechanical, construction, chain, electric of the company is 80000t. Our factories through ISO9001:2000 certificate, has aggressive leadships and outstanding professionals.
Specifications:
Size: (Φ6 - Φ680) x (0.5 - 87) mm, but we can also produce other specification according to the customers’ requirements.
|
|
|
|
Pipes, Tubes, Accessories
