|
|
Standard：
API SPEC 5CT Standard of American Petroleum Institute
Application：
Seamless steel tubes for oil casing and tubing in oil wells
Model N0．of steel tubes：
J55，N80，L80，P110 etc．
|
|
SEAMLESS HYDRAULIC LINE TUBES, PHOSPHATED OR GALVANISED FOR PRESSURE AND RETURN PIPING
Material SI 37.4 (E235+N), St 52.4 nbk(E355+N)
Tol. DIN 2391/C or EN 10304-4
Dimensional Range
4,00 x 1.00 mm up to 80,00 x 10,00 mm also in inch-sizes and free Chromium VI
|
|
|
|
|
|
ULTRA-NW™ is an advanced prefabricated, secondary containment piping system for hazardous chemicals, process waste and general fluid transportation. It is a fiberglass clad stainless steel conduit system with no need for cathodic protection.
ULTRA-NW™ is the next generation for complying with Federal regulations for secondary containment of hazardous fluids, this drainable, dryable and testable, prefabricated, secondary contained piping system is designed for the distribution of jet fuel, radioactive waste, Bio-process waste and chemical transfer. ULTRA-NW™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding 100 mils thick, and designed to withstand a 35,000 volt holiday test. ULTRA-NW™ is supplied with stainless or other high alloy pipe and containment. Single or multiple steel carrier pipes, can be insulated with any type of pipe insulation, we recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system and electric heat tracing.
- Temp Range: 32ºF to 750ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
ULTRA-FS™ is an advanced prefabricated, secondary containment piping system for chemicals, process waste, fuel systems and general fluid transportation is a fiberglass clad steel conduit system with no need for cathodic protection.
ULTRA-FS™ is the next generation for complying with Federal regulations for secondary containment of hazardous fluids, this drainable, dryable and testable, prefabricated, secondary contained piping system is designed for the distribution of hydrocarbons, process waste and chemical transfer. ULTRA-FS™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding 100 mils thick, and designed to withstand a 35,000 volt holiday test. ULTRA-FS™ is a smooth wall, minimum 10 gauge steel conduit. Single or multiple steel carrier pipes, can be insulated with any type of pipe insulation. We recommend mineral wool insulation that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system, and electric heat tracing.
- Temp Range: 32ºF to 750ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
Sewerdrain System
Sewerdrain Pipe and fittings to BS 5481 (EN 1401) were established in the early 1970’s, gaining recognition for a wide range of domestic and civil engineering applications, and have been have been accepted under the building regulations and ‘Sewers for Adoption’, where their performance has been well proven.
Supplied in 3 metre or 6 metre lengths, with socketed or plain ended.
|
|
New from Tyco Fire Suppression & Building Products, Grinnell's G-Press(TM) Piping System is a complete piping system for a sprinkler fire protection installation, offering lower system costs, shorter installation times, reduced installation waste/clean up and is approved to international fire standards.
G-Press systems have been developed to meet the growing need for quicker, more precise sprinkler pipe installations together with the expectation of increased safety and security.
The range includes G-Press Fittings (using the G-Press Fitting Connection Method), the G-Press Passive Leak Monitoring (PLM) Sealing Ring and the G-Press Tube.
|
|
Welding accessories for piping in stainless steel
ISO Unions with conical seat, or with PTFE flat seat(BSP or NPT)
3000 Lbs forged unions (NPT) with socket welding (SW)
Coupling SW, half coupling SW, female cap SW, elbow SW, tee SW
ISO, Metric, ANSI standards
90°elbow, 45° elbow, tee with sleeve, tee without sleeve
Concentric reducer, excentric reducer, collar, pipe cap
...
|
|
|
FG Inox proposes its stainless steel accessories to weld : bends, tees, reducers, caps and collars in ISO, METRIC and ANSI (schedule) standards.
|
|
Stainless steel pipe fittings for dairy and food industries
Béné Inox offers you a complete range of unions and pipes fittings
stainless steel 304L and 316L
for SMS, DIN, Tri-clamp, Macon standars
Butterfly valves (manual or automated), pneumatic seat valves
Check valves, filters, sigth glasses...
Unions for welding, unions for expanding, unions for hose fitting
male part, liner, nut, blind nut, with EPDM/FKM/Viton/PTFE gasket...
SMS/BSP adaptor, DIN/BSP adaptor
Bend at 90°, at 45°, at 180°, tee, reduced tee
Concentric reducer, excentric reducer, pipe cap, collar
Threaded stirrup, clamp, pipe holder, pipe
We also have an "industry" range of fittings (ISO,ANSI standards...) :
Valves, unions, flanges, elbows, tees, réducers...
|
|
FG Inox offers 3 standards of stainless steel of food fittings : SMS, DIN, MACON. Among this standards, FG Inox offers threaded fittings, welding fittings, valves and pipes.
All these products are made for alimentary using.
|
|
Threaded accessories for piping in stainless steel
ISO Unions with conical seat, or with PTFE flat seat(BSP or NPT)
3000 Lbs forged unions (NPT)
Bent unions male/female or female/female (BSP / NPT)
welding nipple, barrel nipple, hexagonal nipple, male plug
female coupling, half coupling, female cap
Bulkhead coupling
Reducer (male/male, male/female, female/female, female/male)
90°elbow, 45° elbow, reduced bend
Threaded tee, reduced tee, cross
...
|
|
316L machined stainless steel unions, threaded, with hose shank or to weld with flat or conical seat.
From ND 5 to ND 100.
MWP at 20C: 64 bars < ND 50 and 40 bars > ND 50
FG Inox proposes 316L stainless steel threaded nipples, barrel or hexagon nipple, adaptors, couplings, elbows, tees, reducers and plugs.
|
|
|
Autoclave Engineers offers Seamless High Pressure Heavy Wall stainless steel tubing for pressures above 10,000 psi (690 bar) up to over 150,000 psi (10,000 bar). Also available in specialty materials such as Inconel, Duplex, Super Duplex, and others. A complete line of Valves, and Fittings are also available.
|
|
Welded, welded and drawn tubes size range »
Up to 38.1mm (1 1/2") OD. Straight lengths up to 16m (51ft), coil tubes (with orbital joints) up to 10000m (33000ft) long.
Our product range consists of straight and coiled tubing. These tubes can be either seamless, welded or welded and drawn.
|
|
Sanpress-Pipe 1.4521, stainless steel, for drinking water installations, in 6 m rods,
Sanpress XL-Pipe 1.4521, stainless steel, for drinking water installations, in 6 m rods,
Sanpress-Pipe 1.4401, stainless steel, for drinking water- and gas installations, in 6 m rods
Sanpress XL-Pipe 1.4401, stainless steel, for drinking water- and gas installations, in 6 m rods
Sanpress-Pipe bow 15°, stainless steel
Sanpress XL-Pipe bow 15°, stainless stee
Sanpress-Pipe bow 30°, stainless steel
Sanpress XL-Pipe bow 30°, stainless steel,
|
|
|
It is available in a variety of compositions, most popular of which are ASTM-A-213, Grade TD-321. (16% Cr, 8%N stabilized with titanium) and ASTM-A-213 Grade TD-347 (18% Cr, 8% Ni) stabilized with columbium. Either of these two may be used upto to 649oC. Care must be given to choice of welding rod to avoid brittleness in the welds.
|
|
WELDED CYLINDER TUBES IN STAINLESS STEEL
Material: AISI 304; 316 L; 316 Tl
Tol. OD DIN 2463
Tol. ID ISO-Tolerance Field H9-H11
Cenler Line Average of Interior Surface drawn Ra max. 1,0 µm
Dimensional Range: ID ø8 - 200 mm
|
|
Stainless Steel Pipe
Seamless to EN ISO 1127
Produced in approx. 6 m lengths
sf 800 m
Stainless Steel Pipe
sf 800 m
Capillary Tube
Microtubing
sf 800 z
Imperial
Stainless Steel Pipe
|
|
|
|
|
|
Top Line Electropolished tubing sets the standard for service in applications requiring finishes to 15RA maximum. Available in sizes from 1/2" to 4" OD, this full finished stainless steel tubing is available from stock or direct from the mill in 20 foot lengths. All electropolished tubing is fully tested and marked per ASTM A450 requirements. 3
All Top line electropolished tubing is packaged using protective 6 mil poly sleeving with air tight end caps. The tubing is then packageg in wood or Tri-Wall corrugated cartons for maximum protection during shipment.
Finish: Electropolished Tubing is standard with a 15RA max ID with bright annealed/mill OD (ASME BPE surface finish code SFT4). Mechanically polished OD to 32RA or 20RA available on application. The same product is available with a 10RA max. surface finish ID.
Annealing: All tubing is Bright Annealed to a minimum of 1900 degrees F (1040° C) and rapidly quenched.
Cleaning: All Top Line electropolished tubing is rinsed with low TOC de-ionized water. The tubing is then dry purged with 99.998% pure Nitrogen which is filtered to .003 micron at the point of use. The cleaning and packaging is done in a class 100< cleanroom.
|
|
|
As the number of large construction projects in areas with weak ground and coastal areas continue to increase, designing and building earthquake-resistant structures has become even more important than before. Accordingly, foundation piles are required to have higher levels of yield strength, workability, and structural reliability. Kubota steel pipe piles meet this requirement. The steel pipe piles have already been used in a number of construction applications such as bridges, ports, rivers, and buildings.
|
|
LSAW Steel Pipe (UOE)
Outside Diameter: ø 508- ø1118mm (20"-44")
Wall Thickness: 6.4-25.4mm (1/4"-1")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 9-12.3m (30'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 600,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
LSAW Steel Pipe (JCOE X 2 Mills)
Outside Diameter: ø 406mm - ø1829mm (16"-72")
Wall Thickness: 6.4-60mm (1/4"- 21/8")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 3-12.3m (10'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 550,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
ERW Steel Pipe
Outside Diameter: ø 114mm - ø 356mm (4"-14")
Wall Thickness: 3.0-12.7mm (1/8"-1/2")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 3-12.3m (10'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 150,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
|
|
|
|
High Quality Fluoropolymer Extrusion
SAT, an ISO 9001 certified company, produces tubing utilizing specially designed extruders and extrusion processes. Our tubing is made using only ultra-high purity (UHP) PFA and FEP raw materials. Thanks to laser technology and state-of-the-art systems, our tubing’s O.D. and I.D. are kept under constant control, as is electrostatic charge neutralization.
Tube cleanliness is ensured during and after extrusion as a result of our contamination control process. In fact, each tube unit receives a positive nitrogen surge and is then immediately capped and packaged in separate, heat-sealed, double polyethylene bags. The tube coils are then stocked in clean room.
Low Extractables for a High-Tech World
Contaminants are a problem you can’t afford. In fact, impurities result in lower chip yields, higher costs and lower profit margins. Why settle for anything less than high-purity products for your manufacturing processes?
SAT’s PFA and FEP Tubings have very low levels of extractable metals, and this high purity characteristic results in higher wafer yields for the semiconductor industry. Furthermore, high purity means lower costs thanks to reduced contamination, and higher profits due to fewer product defects.
SAT’s PFA and FEP Tubing Features:
* Low levels of extractable fluoride ions
* High crack resistance and strength
* Excellent chemical resistance
* High temperature resistance
* Low chemical carryover and permeability
* Non-flammable
* Low ionic attraction
* High weather and aging resistance
* Excellent dielectric properties
* Non-stick
* High mechanical abilities
* High burst pressur
|
|
Waste water disposal systems in semi-conductor, pharmaceutical and bio industry
Transport lines in nuclear, gas, oil and chemical industry
Transport lines of dangerous and corrosive
waste water in groundwater protection areas
|
|
Cold Water Supply
Polypipe manufactures blue polyethylene potable water pipes in 20mm to 63mm diameter. They are manufactured to BS 6572 and are complemented by a full range of Polyfit push-fit and Polyfast compression fittings. Adaptors are available for connections to copper, lead and imperial polyethylene pipes. Service pipes are available in coil sizes of 25, 50, 100 and 150m.
|
|
|
This pile was developed based on the ductile pipe that has long been used for water pipelines, and is usually used as a bearing pile for small buildings. The strength is higher than the commonly used structural carbon steel, and the corrosion resistance is more than two times higher. The ducpiles securely support a building, contributing to improving the safety of a house or other small structure.
|
|
| ... products without technical information |
| |
|
|
Pipes, Tubes, Accessories
