|
|
The G-Series are Solid State AC Power converters from 18kVA to 90kVA.
G-Series Systems are readily configurable as manufacturers of frequency converters, line conditioners, programmable industrial test systems, and uninterruptible power systems.
The basic building block of a G-Series AC Power System is the mainframe. The mainframe consists of the professional cabinet and AC to Dc power supply. Up to five mainframes may be paralleled to increase system output power up to 90 kVA.
Each Pacific power source is burned in and meticulously tested before it can leave the Pacific factory. With close attention to detail, handcrafted workmanship comes through with every system delivered.
Due to its modular design, failed device disconnect circuitry, and on-line module replacement, Pacific G-Series Systems are unmatched in reliability and ease of service.
|
|
The AMX Series is a family of High Performance Linear AC power sources covering the power range from 500 VA to 12 kVA (Optional to 30kVA). The product line offers both single and three phase models.
An exceptionally broad bandwidth (50 kHz small signal) combined with peak/RMS current of 4-6:1 give the AMX Series the ability to produce high quality, low distortion output power into the most dynamic loads.
Key Features Provide Application Versatility
-CE and ETL Mark available
-IEEE-488.2 or RS-232C with SCPI compatibility
-LabVIEW for Windows®/LabWindows® drivers
-Waveform Creation by Harmonic Synthesis
-Graphical Analysis (Voltage and Current)
-Harmonic Analysis (Voltage and Current)
-Metering of RMS and Peak Values
-Continuous Self Calibration (CSC)
-Line Sync Option
-6:1 Peak Current Capability
-Low Impedance for IEC555 Testing
-Programmable Output Impedance
-Up to 0-300 VAC Direct Coupled Out, Higher voltage ranges available
-1 Phase / 3 Phase Switch Selectable from front panel or bus command
-20-5000 Hz Full Power Bandwidth
-Power Levels from 500 VA to 30 kVA
-Externally Referenced Meter Calibration
|
|
The ASX Series is a family of High Performance Switching AC power sources covering the power range from 1.5kVA to 6kVA (12kVA to be released soon). The product line offers both single and three phase models.
Power conversion within the ASX Series is achieved by high frequency pulse width modulation, resulting in cool, quiet and efficient operation.
Key Features Provide Application Versatility
- CE or ETL Listed available on request
-22 Waveform Library - Arbitrary Waveform Industrial generator
-15 to 1,200 Hz Operation - 5,000 Hz Bandwidth
-Precision True-RMS metering of volts, amps, and power for professional displays and reporting
-RS-232 Interface with SCPI compatibility
-1 Phase/3 Phase Switch Selectable Output from front panel or bus command
-99 stored programs for both static and dynamic Transient Testing
-LabVIEW for Windows®/LabWindows® drivers
-Waveform Creation by Harmonic Synthesis
-Harmonic Analysis (Voltage and Current)
-Metering of RMS and Peak Values
-Continuous Self Calibration (CSC)
-Precision Voltage Programming - 0.05% with CSC engaged
-Programmable Output Impedance
-Up to 0-300 VAC Direct Coupled Out
-Power Levels from 1.5 kVA to 12 kVA
|
|
| Our power supplies suppliers are used in test laboratories, service centres, research and development departments and for production quality testing. They can be supplied with isolation windings, manual or automatic controls, electronic regulators or rectifiers to provide a DC output. |
|
Alternative power supply specifications 150 va
The EFS 8171 power supply provides a sinusoidal output, isolated from the line.
The output frequency may be set from 50 to 60 Hz and adjustable from 0 to 700 vrms in 6 ranges. |
|
With the combined voltage and current source in a single compact professional chassis, the FX Series is the ideal choice for the simulation of high power professional levels. Either single or multi-phase, this versatile source can simulate power levels from just a few milliwatts
to 54kW single phase or 162 kW three-phase and provides a universal system for both manual and programmable control applications. |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
... see all the products in the category
Fuel cells
|
| Following the state-of-the-art trend in automation for decentralized systems without professional cabinets MTM Power has designed the new series PM-IP67A with 50, 75, 100, 150 and 200 W. Remarkable feature of the primary switched modules is that they are suitable for applications with protection degree IP67 for different tasks in indoor and outdoor industrial applications. Without any additional protection against harsh environmental conditions these power supplies manufacturer can be mounted and used just at the place where needed. The compact power supplies with AC and DC wide input range are designed for worldwide use and are available with single and dual outputs of 5, 12, 15, 24, 36, 48, ±12, ±24, ±36, ±48 and 12/24 VDC. Their dimensions are 166,0 x 85,0 x 35,0 mm and they are connected via 7/8" interconnectors. The devices are vacuum encapsulated, acc. to Protection Class 2 and comply with the Low Voltage Directives as well as with the up-to-date EMC Standards as regards CE Conformity. Further features are rugged design, SMD-technology, automatic 100 % final test and 100-%-burn-in-test. The series PM-IP67A is short circuit protected, needs no ground load and is operating within a temperature range of -40 to 75 °C. |
|
| Factorized Power Architecture maximizes a power system by providing a high degree of system flexibility, superior power density, efficiency, transient response, and reliability. This new architecture is enabled by V-I Chip components: the BCM intermediate bus professional converter, the PRM non-isolated regulator, and the VTM current multiplier. These families of integrated power components provide new ways to create small, cost-effective, high-performance power system solutions. |
|
| ... products without technical information |
| |
The ES51 high voltage manufacturers of power supplies are power supply units for the series R5X AC discharge bars.
The discharge bars and the ES51 power supply are used mainly in cases where disruptive static charges on fast-moving material webs impair production processes and need to be eliminated.
The ES51 power supply features the following characteristics:
• 5 plug-type high voltage outputs
• stable 5 kV AC output voltage
• small dimensions
• easy installation
• protection class IP 54 design
• function and malfunction monitoring of the bars with floating signal contacts (optional) |
|
|
|
