|
|
MTM Power GmbH, the specialist for high quality smpss, offers in its program the 19" Euro Card with up to six different, galvanically isolated outputs with 6 or 8 TE. With the MTM Power Card of the series MPK1, an unexpected variety of possibilities can be created for 19" applications. Approx. 1.000 different power supply variations as
19" plug-in can be realised. As in a construction kit, the 19" power supplies can be individually assembled with the three basic components front plate, PCB and manufacturer of connector as well as the vacuum encapsulated modules of the series PMA, PMAS, PMN, PMG and PML. The MPK1 offers 2 mounting positions for PCB modules with an output power of 5 to 48 W, either with single, dual or triple outputs. The MPK2 has one mounting position for modules with an output power of 50 to 100 W and up to three outputs. With the MTM Power Card, power supply variations can be realised in seconds. If requested, a separate LED for each output can be included on the front plate. All modules with the same input voltage can be combined with each other. As customised power supplies have the same dimensions and pinning, even these can be combined with standard modules. |
|
AC/DC power-supply units
The wide range of AC/DC power-supply systems supplied by
Zentro-Elektrik includes devices with one or several output voltages, switched mode or series-regulated devices, modular power-supply systems, including units with hot-swap features and a large selection of power-supply systems in general.
They can be used in various applications as individual devices or redundant system solution or even as battery chargers and DC PROFESSIONAL UPS units. |
|
| A range of multi function products specifically designed to suit the requirements of all combined heat and power, co-generation, diesel and industrial gas engine professional generator applications. This high quality product portfolio offers the power generator manufacturer and panel builder a flexible mix of contemporary and traditional products, including a comprehensive range of generator set controllers, integrated digital power metering, and a %u2018one stop%u2019 solution package of measurement, protection and control instrumentation. |
|
Open frame
Power systems
- From 300 W to 1000 W output power
- (n + 1) redundancy
- Design in 3 U subrack
19"
- AC/DC switched mode power dispenser
- AC/DC linear control systems
- AC/DC converts
|
|
VIPAC Low Profile - 50-900 Watt Suppliers of power supply
The VIPAC family of power systems is a new class of user-defined, modular power solution. It incorporates pre-assembled and tested front ends, Maxi, Mini and Micro DC-DC converters, a choice of output connections and mechanical platforms. |
|
| ... products without technical information |
| |
Designed with a steel frame and sequential ratchet rack to optmise load volume and maximise ergonomics.
Custom-made models available on request. |
|
MEASUREMENTS:
Total height: 860 mm.
Base: 1210 x 2290 mm.
PRINCIPAL CHARACTERISTICS:
* For measurements of professional tires of "cars"
* Folding(pliable) and apilabes.
* You guide for lift truck.
ENDED IN:
Galvanized electrolytic. |
|
Specially-designed steel frame pallets for the transport and storage of tubing and other bulky products.
Custom-made dimensions abailable. |
|
BPR retention Pallet Tray
NEW: The BPR is also available in 400L and 200L versions.
The retention pallet tray is made of steal and has been designed for the storage and outside decanting of liquid products that may contaminate the ground. This tray has been clearly studied to offer a secured use on the building and civil engineering sites. The BPR can store a 1000L professional container or two 200L barrels, or several barrels with a total capacity under 1080L, to comply with the actual legislation.
- 1 steel mesh surface with 2 different positions by manual operation:
Flat surface for a 1000L container or several tanks.
Barrel support on rollers with a latch system for two 200L tanks.
- 1 lower shelf to facilitate and secure the decanting of the products.
- 2 entry ways for a supplier of forklift truck lifting.
- 1 prehension device with 4 lifting eyes on the upper part for a professional crane lifting (Can only be moved with all professional doors closed).
- 1 mesh wired covering front door with industrial locker.
- Lateral and rear doors for weather protection.
- The lateral walls are articulated to facilitate the attachment of the tanks or containers.
- 1 protecting roof separated in 2 removable parts to enable the crane to lift the BPR with a 1000L container inside.
- 1 document protection pocket fitted inside the BPR.
- Possibility to personalize the BPR. |
|
| ... products without technical information |
| |
These industrial presses are suitable when constant precision and force are required throughout the entire stroke of the pin.
They are used for the Assembly of bushings and bearings specifications, deformation of sheets, assembling, etc. |
|
ManualPresses are the economical solution for short run productions. The design of these professional presses is the direct result of our experience in multiple applications. They carry the hallmark of quality and precision. They provide:
Flexibility
- fast and easy set up
- quick and repeatable tool changeover
Ergonomic design
- hand lever position can be varied by 360°
- left and right hand versions available
Precision alignment
- smaller than 0.05 mm (precision ram and table bores)
Maintenance free |
|
DIRECT ACTING PROFESSIONAL PRESSES
Rack-and-pinion presses with round ram
APZ series
mäder rack-and-pinion presses transmit their pressing
force constantly over the entire length of the stroke.
Direct power transmission via the hand lever permits
extreme precision in the pressing operation.
The improved transmission ratio enables a higher compression
force to be achieved for the same force
applied.
The following quality features are characteristic of all
mäder rack-and-pinion presses:
- anti-twist ram
- infinitely adjustable stroke length:
Standard: via setting screw
MICRO: via manufacturers of micrometer screw
- Height adjustment of the press head using
a threaded suppliers of spindle
- 360° infinitely adjustable hand lever
- adjustable return stroke power
Rack-and-pinion presses are therefore ideal for:
- pressing-in longer components and for
- jointing operations over long strokes |
|
... see all the products in the category
Presses
|
|
|
see the results for the following category
