|
|
MTM Power GmbH, the specialist for high quality power supplies, offers in its program the 19" Euro Card with up to six different, galvanically isolated outputs with 6 or 8 TE. With the MTM Power Card of the series MPK1, an unexpected variety of possibilities can be created for 19" applications. Approx. 1.000 different power supply variations as
19" plug-in can be realised. As in a construction kit, the 19" power supplies can be individually assembled with the three basic components front plate, PCB and connector as well as the vacuum encapsulated modules of the series PMA, PMAS, PMN, PMG and PML. The MPK1 offers 2 mounting positions for PCB modules with an output power of 5 to 48 W, either with single, dual or triple outputs. The MPK2 has one mounting position for modules with an output power of 50 to 100 W and up to three outputs. With the MTM Power Card, power supply variations can be realised in seconds. If requested, a separate LED for each output can be included on the front plate. All modules with the same input voltage can be combined with each other. As customised power supplies have the same dimensions and pinning, even these can be combined with standard modules.
|
|
AC/DC power-supply units
The wide range of AC/DC power-supply systems supplied by
Zentro-Elektrik includes devices with one or several output voltages, switched mode or series-regulated devices, modular power-supply systems, including units with hot-swap features and a large selection of power-supply systems in general.
They can be used in various applications as individual devices or redundant system solution or even as battery chargers and DC UPS units.
|
|
Open frame
- 3 or 4 output voltages
- VME bus signalling
- Fan monitoring
Power systems
- From 300 W to 1000 W output power
- (n + 1) redundancy
- Design in 3 U subrack
19"
- AC/DC switched mode power supply
- AC/DC linear control systems
- AC/DC converts
|
|
|
A range of multi function products specifically designed to suit the requirements of all combined heat and power, co-generation, diesel and gas engine generator applications. This high quality product portfolio offers the generator set manufacturer and panel builder a flexible mix of contemporary and traditional products, including a comprehensive range of generator set controllers, integrated digital power metering, and a %u2018one stop%u2019 solution package of measurement, protection and control instrumentation.
|
|
VIPAC Low Profile - 50-900 Watt Power Supply
The VIPAC family of power systems is a new class of user-defined, modular power solution. It incorporates pre-assembled and tested front ends, Maxi, Mini and Micro DC-DC converters, a choice of output connections and mechanical platforms.
|
|
| ... products without technical information |
| |
Flip Mirror Holder KSH 90
The swing leaf bears a wobble plate with an adjustment range of ± 0.5° and an aperture of 2". Optics with a thickness > 12 mm (normally 2" mirrors) are fixed with a plastic screw.
Optical components (such as mirrors and beam splitting paltes) having a thickness of only 10 mm can be pressed aganst three stops with the enclosed two clamping shoes and thus fixed.
The swing angle is 45°, the repeatability < 100 µrad. The swing time of the motorized version is about 1 s.
- for use with SYS 90
- black anodized aluminium alloy
- mountable onto pin or slide
- manual operation or motorized
|
|
The laser mirror mounts are high-precision trans-adjustment devices, specially conceived for the use as resonator mirror mounts. Using a RT 65 slide and a S 65 profile rail, a highly stable laser resonator can be set up. The adjustment mounts have a central hole with a 35 mm diameter to hold mounted optics or other components. The horizonatl and vertical angles can be adjusted independently of one another. The maximum tilt is 6° (±3°).
Fine-thread screws with a 0.35 mm pitch are available as adjustment elements. On demand, short fine-thread screws with hexagon socket and locking are available for application in serial devices.
- for use with SYS 65
- suitable for mounting laser resonators
- mountable onto pin or slide
|
|
Lens holders are designed to position miniature lenses over CCD/CMOS imagers with high degree of accuracy. Lens holder must keep the lens optic axis centered on the active area of the imager. It must also keep the lens axis perpendicular to the imager surface. Some lens holders also provide special features for holding IR cut-off filters and optical low-pass filters. Lens holders are precision-molded with special plastic materials.
|
|
|
The adjust.x™ mirror mounts are equipped with three fine thread screws made of stainless steel in a brass bushing. Using tight tolerances, the screws have low hysteresis and backlash. These screws guarantee a wobble free movement, high precision and long-term stability. We only offer these screws as allen-key version. One knob will be delivered with each mirror mount.
|
|
| ... products without technical information |
| |
Flip Mirror Holder KSH 90
The swing leaf bears a wobble plate with an adjustment range of ± 0.5° and an aperture of 2". Optics with a thickness > 12 mm (normally 2" mirrors) are fixed with a plastic screw.
Optical components (such as mirrors and beam splitting paltes) having a thickness of only 10 mm can be pressed aganst three stops with the enclosed two clamping shoes and thus fixed.
The swing angle is 45°, the repeatability < 100 µrad. The swing time of the motorized version is about 1 s.
- for use with SYS 90
- black anodized aluminium alloy
- mountable onto pin or slide
- manual operation or motorized
|
|
The laser mirror mounts are high-precision trans-adjustment devices, specially conceived for the use as resonator mirror mounts. Using a RT 65 slide and a S 65 profile rail, a highly stable laser resonator can be set up. The adjustment mounts have a central hole with a 35 mm diameter to hold mounted optics or other components. The horizonatl and vertical angles can be adjusted independently of one another. The maximum tilt is 6° (±3°).
Fine-thread screws with a 0.35 mm pitch are available as adjustment elements. On demand, short fine-thread screws with hexagon socket and locking are available for application in serial devices.
- for use with SYS 65
- suitable for mounting laser resonators
- mountable onto pin or slide
|
|
|
The adjust.x™ mirror mounts are equipped with three fine thread screws made of stainless steel in a brass bushing. Using tight tolerances, the screws have low hysteresis and backlash. These screws guarantee a wobble free movement, high precision and long-term stability. We only offer these screws as allen-key version. One knob will be delivered with each mirror mount.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category
