|
|
|
The MTM Power series PMA19 35 has been designed for the use in 19" racks. Due to the very slim case with only 4 TE, the PMA19 35 require very little space within the complete system. The devices have been designed as universal compact power supplies with input voltage ranges of 85...264 VAC and 80...375 VDC for worldwide application. The switching frequency is 80 kHz and they are equipped an internal fuse at the input. The nominal outputs of 5 V, 12 V, 24 V and 48 V are adjustable. Despite the compact design, the devices fulfill all common safety and EMI standards, are prepared for Class I and have a high efficiency. They are continuous short circuit and overload protected and optionally available with a power fail signal.
|
|
|
|
|
|
MTM Power GmbH, the specialist for high quality power supplies, offers in its program the 19" Euro Card with up to six different, galvanically isolated outputs with 6 or 8 TE. With the MTM Power Card of the series MPK1, an unexpected variety of possibilities can be created for 19" applications. Approx. 1.000 different power supply variations as
19" plug-in can be realised. As in a construction kit, the 19" power supplies can be individually assembled with the three basic components front plate, PCB and connector as well as the vacuum encapsulated modules of the series PMA, PMAS, PMN, PMG and PML. The MPK1 offers 2 mounting positions for PCB modules with an output power of 5 to 48 W, either with single, dual or triple outputs. The MPK2 has one mounting position for modules with an output power of 50 to 100 W and up to three outputs. With the MTM Power Card, power supply variations can be realised in seconds. If requested, a separate LED for each output can be included on the front plate. All modules with the same input voltage can be combined with each other. As customised power supplies have the same dimensions and pinning, even these can be combined with standard modules.
|
|
Open frame
- 3 or 4 output voltages
- VME bus signalling
- Fan monitoring
Power systems
- From 300 W to 1000 W output power
- (n + 1) redundancy
- Design in 3 U subrack
19"
- AC/DC switched mode power supply
- AC/DC linear control systems
- AC/DC converts
|
|
|
|
|
|
The 9130 is a fully programmable triple output DC Power Supply delivering 0-30V/0-3A on 2 outputs and 0-5V/0-3A on 1 output. Each output is fully floating and outputs can be adjusted independently or connected in series or parallel to produce higher voltages or currents. The 9130 is ideally suited for applications in Electronic Test, Production and Service, where multiple independent DC supplies are required and bench space is at a premium.
# 3 independent, fully programmable and electrically isolated outputs
# Display & adjust Voltage and Current settings for all 3 channels simultaneously
# Flexible output configuration: Operate in series or parallel tracking mode
# SCPI compatible command set. Communicate via USB interface using the included USB to TTL Serial Converter cable
# RS232 interface cable, converting from RS232 to TTL, is optional (order IT-131)
# OVP (Over Voltage) and OTP (Over Temperature) protection
# Output on/off control
# Excellent stability and regulation
# Very compact foot print (rack mountable 2U x 1/2U)
# Application Software for front panel emulation and simple test sequence generation included
# 50 memory locations for instrument state storage & recall
|
|
[MICRO REDUNDANT] M1S2-5400V4H
VOLTAGEF 90`264VAC FULL RANGE
FREQUENCYF 47`63HZ
INPUT CURRENTF3A(RMSjFOR HIGH RANGE INPUT VOLTAGE / 6A(RMSjFOR LOW RANGE INPUT VOLTAGE
INRUSH CURRENTF20A MAX. FOR 132 VAC PER MODULE / 40A MAX. FOR 264 VAC PER MODULE
EFFICIENCYF84%~85% MAX. TYPICAL AT FULL LOAD
DIMENSION: 355.00x106.00x41.30 (mm) / 13.98x4.17x1.63 (inch)
SAFETYFUL 60950-1, CSA 22.2 NO.60950-1-03 1ST Edition , TUV IEC60950-1, CCC
BEST SOLUTOIN FOR: Server,Workstation,Storage System
|
|
In the area of suppression modules for contactors, valves and motors, we offer the corresponding components to increase EMC throughout the whole installation. We can meet all normal requirements in the field of power supplies with our power supply units, incorporating primary switching technology and control-power transformers.
Interface technology is represented in the Lutze programme by a wide range of different components that can be used to create just about any interface needed in your application.
|
|
# Models 1785B, 1786B, 1787B & 1788 are Programmable DC Power Supplies that offer new levels of "ease of use" and programmable functionality. Direct key in entry makes voltage and current selection fast, accurate and easy. In case calibration allows for simple, cost savings, uninterrupted operation. Sixteen user programmable preset outputs
# Controllable Output On/Off Switch
# 10mV/10mA setability resolution
# Closed case calibration
# Low ripple and noise
# Excellent temperature stability
# Serial interface cable and software included
|
|
# BK Precision's new Model 1761 Triple Output DC Power Supply offers outputs with two 0 to 35V, 0 to 3A and one 2 to 6.5V, 5A outputs with two 4 digit LED displays. The 4 digit LED displays offer 10mV and 1mA resolution which provides higher accuracy. This makes it an ideal supply for power sensitive applications. The 1761 is fully overload protected and comes with a two year warranty. Continuously monitor voltage and current output on two 4-digit LED displays
# Connect two supplies in parallel to double the current output
# Connect two supplies in series to double the voltage output
# Reliable, Durable
# Operate continuously at full load without overheating
# Fully overload protected
# Coarse and fine voltage controls
# Excellent regulation
# Very low ripple
# Constant voltage or constant current operation
|
|
The models 1790 is a cost effective, high power, regulated DC power supply with 640 Watt output (0 to 32V, 0 to 20A). It is a linear high current DC power supply suitable for bench operation or standard 19" rack operation. This linear power supply is a high power workhorse that will easily deliver clean power to your high current circuits.
Constant Voltage/Constant Current Operation
Remote Programming Facility
Facility for Presetting the Output Voltage and Max.
Load Current Limits
Separate DC Output ON/OFF Switch
Remote Sensing Facility
High Stability and Close Regulation 0.01%
Meet CE Specifications
|
|
|
The product family PMN/PCMN with low voltage input completes the range of primary switched MTM Power Modules. The modules offer input ranges of either 20/30...60 VAC or 18/30...72 VDC and allow - due to the different types available in this series - efficient solutions in numerous application fields. The vacuum encapsulated devices offer an isolation of 3,3 kVrms and comply to the up-to-date EN standards as regards CE conformity. Further features are rugged design, SMD-technology, automatic 100 % final test and 100-%-burn-in-test. The series PMN/PCMN offers 10 and 30 W constant output power, is short circuit protected, needs no ground load and is designed for PCB-mounting (PMN) or chassis mounting (PCMN).
|
|
|
|
|
|
|
Following the state-of-the-art trend in automation for decentralized systems without cabinets MTM Power has designed the new series PM-IP67A with 50, 75, 100, 150 and 200 W. Remarkable feature of the primary switched modules is that they are suitable for applications with protection degree IP67 for different tasks in indoor and outdoor industrial applications. Without any additional protection against harsh environmental conditions these power supplies can be mounted and used just at the place where needed. The compact power supplies with AC and DC wide input range are designed for worldwide use and are available with single and dual outputs of 5, 12, 15, 24, 36, 48, 12, 24, 36, 48 and 12/24 VDC. Their dimensions are 166,0 x 85,0 x 35,0 mm and they are connected via 7/8" connectors. The devices are vacuum encapsulated, acc. to Protection Class 2 and comply with the Low Voltage Directives as well as with the up-to-date EMC Standards as regards CE Conformity. Further features are rugged design, SMD-technology, automatic 100 % final test and 100-%-burn-in-test. The series PM-IP67A is short circuit protected, needs no ground load and is operating within a temperature range of -40 to 75 C.
|
|
The model 9124 is a laboratory grade, 0-72V/0-1.2A programmable DC Power Supply providing great performance and features not found in other supplies in this price category. The power supply was designed to meet the needs of todays applications in R&D design verification, production testing or university labs that require clean and reliable power, high resolution/accuracy and fast transient response time.
* Excellent display resolution
* Fast transient response time (<20ms)
* SCPI compatible
* RS232 interface (standard), USB optional
* Closed case calibration
* Compact size for bench use or rack mountable (2U x 1/2U size)
* DVM and Miliohm meter
* Discrete Fault Indicator/Remote Inhibit (DFI/RI). Useful for turning multiple power supplies On/Off simultaneously
* Application Software for front panel emulation and simple test sequence generation included
|
|
Our broad selection of both bench-friendly and system-ready instruments can meet your testing challenges - from basic to complex - with a wealth of available capabilities.
* Test confidently with clean, precise DC power that's fully specified and guaranteed
* Safeguard loads from potential harm with robust output protection and fault detection capabilities
* Enhance system flexibility with built-in, DMM-quality measurement functions
|
|
[True Redundant] MTW4-5C50V3H
* TOTAL MAX OUTPUT OF +5V AND +3.3V NOT EXCEED 380W.
* TOTAL OUTPUT MAX: 1250W
* EFFICIENCY: >80% AT 115VAC, 30%~100% MAX LOAD
* SAFETY: TO MEET UL, TUV, CB IEC60950
*BEST SOLUTOIN FOR: Server,Workstation,Storage System,IPC,Communication,Networking
* DIMENSION: 340.00x422.00x43.00 (mm) / 13.39x16.61x3.27 (inch)
|
|
# The Model 1672 is a Quad Display Triple Output DC Regulated Power Supply that provides one fixed output (5V/ 3A) and two variable outputs (0 32V/ 0 3A) ratings. The four displays allows the user to continuously monitor the voltage and current values of the two main outputs. The variable outputs can work independently, or in series tracking, or parallel mode. Independent control of Voltage and Current for variable output
# CV/CC operation
# Separate 3 digit displays for voltage (Green) and current (Red) for both variable outputs
# LED indication for CV (Green) and CC (Red) modes
# Overload indication LED for Fixed output
# Series tracking and parallel mode operation for Triple output unit
# Output terminals are banana style (not binding posts), click on Accessories for leads
|
|
Systems with a DC outlet transform the input alternative voltage, which was pre-conditioned, into a direct, filtered and controlled voltage supported by a series of batteries which is the ideal power supply for Telecommunications operator equipment and other types of equipment with a DC power supply, in which a faulty supply make cause the interruption of the services offered to customers or defects in the production, etc.
SALICRU has two ranges of rectifiers DC Power Systems DC Series OPTIMUS and energy systems of the DC series FAC P.
|
|
|
The PSR series power supplies are regulated DC power supplies capable of operating from 100/240 VAC input, 50/60 Hz. The PSR power supplies include a shunt regulator and blocking diode. They can be used with any controller/amplifier combination to provide a complete solution for single- or multi-axis applications. The PSR series are available in two models: PSR-12-24 and PSR-6-48.
|
|
In the area of suppression modules for contactors, valves and motors, we offer the corresponding components to increase EMC throughout the whole installation. We can meet all normal requirements in the field of power supplies with our power supply units, incorporating primary switching technology and control-power transformers.
Interface technology is represented in the Lutze programme by a wide range of different components that can be used to create just about any interface needed in your application.
Ltze Power Supply Units: Filtered, single-phase and three-phase; All power supplies carry UL-CSA approval; Layout according to EN 61558-2-6 or EN 61000-3-2 and 3-3; 100% ED at nominal load up to 60C.
Ltze Primary Switched Power Supplies: Single-, two- and three-phase; Universal usage thanks to wide-range input 85-550V; Versions for 2-,5-,10-,20- and 40 A, with Power Boost function; Overload or shutdown function; Snap-fit on 35mm DIN rail; PFC.
|
|
[Cloud Power] P1U-5150E
For cloud computing technology, Zippy announce corresponding technology high efficiency PSU for cloud computing equipment. This technology can monitor and control cloud computing power operation in any place through internet.
* TOTAL OUTPUT POWER: 150W
* EFFICIENCY: 80% TYPICAL, AT FULL LOAD 115VAC
* SAFETY: TO MEET UL, CSA, TUV, CCC
* BEST SOLUTOIN FOR: Server,Workstation,Storage System,IPC,Blade server,PCs,Communication,Networking
|
|
|
MTM Power GmbH, the specialist of individual power supplies, offers power supplies for DIN rail mounting with 15 to 75 W. These primary switched modules have been designed as universal compact power supplies with wide input ranges for worldwide applications in switching cabinets and allow an efficient, cost-saving solution for different tasks. They are vacuum encapsulated which allows the use under critical environmental conditions. Further features are rugged design, SMD-technology, automatic 100 % final test and 100-%-burn-in-test. MTM Power DIN rail power supplies comply with the Low Voltage Directives as well as the up-to-date EN standards as regards CE conformity. All devices are short circuit protected, need no ground load and are available with various modification possibilities.
|
|
|
|
|
|
|
MTM Power GmbH, the specialist of individual power supplies, has designed a new generation of DIN rail power supplies, series HSA, for industrial application. As universal compact power supplies, they have an output power of 120 or 240 W. One of the major advantages is to increase to a maximum the readiness for operation of the system to be supplied even under difficult conditions. With dimensions of 50 x 130 x 130 mm (HSA120) and 80 x 130 x 130 mm (HSA240), they perfectly fit into cabinets only offering little space. The devices are available with output voltages of 12, 24, 36 and 48 VDC. They have a high efficiency of up to 89 %, are continuously short circuit protected and need no ground load. The output current is electronically limited in case of overload and the devices then change into constant current operation. Due to this characteristic curve and the reduction of the output voltage to 0 V at the same time, they are protected against short circuit damages and thus offer the possibility to supply loads with high inrush currents without switching-off or intermitting resp.
|
|
[Medical] MQ1G-1060V-12
Appreciating for most major brands of Medical Health-Care providers equipment - bundling Zippy Medical Grade PS in.
* TO MEET IEC60601
* EFFICIENCY85% (+/-2%) AT 115VAC/230VAC AND LOAD CONDITION: 12V/5A
* LEAKAGE CURRENT: 0.3MA MAX. AT NOMINAL VOLTAGE 264VAC
* BEST SOLUTION: Server,Workstation,Storage System,Communication,Networking
* DIMENSION: 101.60x50.80x30.00 (mm) / 4.00x2.00x1.18 (inch)
|
|
|
Test laboratories are confronted by a huge range of electrical and electronic products with vastly differing power requirements. Frequency and voltage combinations not available from the mains power outlet. Test samples that cause inadequate supplies to cave-in under load. PS3, from EMC PARTNER, solves these problems instantly. Convert the mains wall plug into a custom AC and DC power supply, changeable at the push of a button to any pre-selected frequency or voltage combination.. PS3 is flexible enough to perform EMC immunity tests for CE mark compliance yet stable and robust enough to drive magnetic field antennas. PS3 can be used for industrial, telecom, transport and a host of other applications. An innovative design incorporating the very latest technology, PS3 gives the right power right when its needed.
|
|
Absopulse's modular power systems are comprised of plug-in (Eurocard) converter and rectifier modules, and 19" and 23" shelves including motherboards and power distribution panels. These modular designs allow for easy servicing in the field.
Our modular systems offer:
- Output power up to 5kW per 19" shelf
- Almost any input/output and mechanical configuration
- N+1 redundant operation and hot-swap
- Multiple outputs
- Expandability - as power requirements increase, more modules can be added.
- Reconfiguration option
|
|
AC/DC power-supply units
The wide range of AC/DC power-supply systems supplied by
Zentro-Elektrik includes devices with one or several output voltages, switched mode or series-regulated devices, modular power-supply systems, including units with hot-swap features and a large selection of power-supply systems in general.
They can be used in various applications as individual devices or redundant system solution or even as battery chargers and DC UPS units.
|
|
|
|
|
|
DC UPS Systems for Safety Relevant Installations
With their modular construction, the latest DC UPS systems in the GTLB/GTPB series from Zentro Elektrik expand the existing comprehensive range of DC UPS systems for supplying power to safety relevant installations.
The AC/DC systems in standby parallel mode are designed for outputs
from 250 Watt up to 600 Watt and fitted with batteries at the customers request. Additional DC/DC converters can be added to the system if more output voltages are required.
A battery control and monitoring module allows to control the charging current and temperature control of the charge closing voltage.
Over and above this, numerous monitoring and control signals are provided via relays, LEDs or potentiometers. A signal relay, for example,
if the charging voltage fails, to switch off the battery on it reaching the closing discharge voltage, to give advance warning of reaching closing discharge voltage with an additional adjustable threshold or individual limitation of the battery charging current to prolong battery life, and
many more. LED displays and adjustable potentiometers provide for comprehensive signalling and the ability to adjust the maximum charging voltage or the defined point of battery switch-off.
|
|
Our Power Supply with single to 4 channels and digital/analogue display series. Its high stability and enhanced linearity makes this regulated DC power supply significantly useful in where high performance and stable power sources are required. It is widely adopted for R&D, educational and industrial usage.
General Features:
- Single to 4 adjustable channels
- 0-30V voltage linearly adjustment
- 2 display for voltage and current
- Low noise and ripple (<1mV)
- voltage and current pre-set feature
- CV/CC mode auto change
- Full LOADING continuous operation over 16 Hrs
- Conforms to EN61010-1
|
|
Bench Top power supplies are recommended for research and laboratory use. They offer flexibility in terms of voltage range and output polarity. These are stand-alone units which all feature an output voltage display.
The PM20D and PM30D dual output supplies include a 4 digit LCD read out and low voltage (+-5V and +-12V) supplies. Lower cost versions, PM20S and PM30S offering only single polarity output are also available. All supplies in this range accept ac or dc input - referred to as universal supply input.
features :
- mains input
- output range up to 3000V
- low ripple
- positive or negative HV
- overload protected
- clear display of output voltage
- multi-turn set dial
|
|
|
The NEW and compact generation of AC-DC converters with universal input range for worldwide use. This small 150 W unit, is available with 5 single outputs. Its very compact design with an ultra low profile suits very well for U1-size racks and systems. A highly effiecient (89-90%) and reliable converter for high end applications like Semiconductor-equipment, traffic-information systems, LED displays, etc. NEE Series are safety approved acc. to UL, C-UL EN.
|
|
GlobTek brings to power supply design and production the same skills and advantages that have made us number one customer's choice for over 25 years. Our vertical integration, highly efficient facilities, and steadfast obligation to quality and service excellence have enabled us to provide high-value custom engineered power supplies to many satisfied customers.
GlobTek engineers, designs, and manufactures both standard and customized AC-AC, AC-DC, DC-DC power supplies. Our designs fulfill power requirements ranging from 5 watts to 2 kilowatts. GlobTek's greatest advantage is our pledge to serving our customers. Recognizing your need to lower costs and get products to market faster, our team delivers your solution on time and on budget.
|
|
|
|
