|
|
|
Drum clamps are widely used in the petroleum and chemical industries and in other applications that require the handling of standard 55-gallon drums. Drum clamps can also help improve productivity by handling up to four drums per load.
|
|
|
|
|
|
RAVAS supplies a complete range of scales for mounting on forklift trucks.
RCS system
For simple check weighing, where a high accuracy is not required, there is the RCS hydraulic load indication system. With the RCS an oil pressure sensor is installed onto the hydraulic circuit of the forklift by means of a T-coupling. The indicator in the cabin translates the measurement into a weight indication of the load on the forks. The RCS has a limited accuracy, with a possible error of maximum 2% of the lifting capacity of the truck.
The system is meant for simple check weighing, such as the checking of incoming goods, and for avoiding the overloading of lorries, warehouse racking and the forklift truck itself.
RCS PLUS system
The RCS PLUS is an accurate hydraulic weighing system for forklift trucks. On a forklift truck with a capacity of 2.500 kg the weight graduation is displayed in steps of 2 kg, with a 5 kg tolerance (+/- 0.2%). The RCS PLUS weighs by measuring the pressure in the hydraulic lifting system of the forklift truck, via a temperature compensated sensor on a valve block.
During a controlled descent of the mast the pressure in the hydraulic system is measured repeatedly, the software translates these measurements into an accurate weight indication of the load on the forks.
|
|
RAVAS supplies a complete range of scales for mounting on forklift trucks. For simple check weighing, where a high accuracy is not required, there is the RCS hydraulic load indication system.
An oil pressure sensor is installed onto the hydraulic circuit of the forklift by means of a T-coupling. The indicator in the cabin translates the measurement into a weight indication of the load on the forks. The RCS has a limited accuracy, with a possible error of maximum 2% of the lifting capacity of the truck. The system is meant for simple check weighing, such as the checking of incoming goods , and for avoiding the overloading of lorries, warehouse racking and the forklift truck itself.
|
|
Allow you to ship, receive and warehouse unit loads on inexpensive slip sheets rather than pallets. Products typically handled with a push/pull include bagged products such as seed, agricultural products and cement; cased food, electronics, cosmetics and bottled beverages.
Cascade manufactures a variety of products that enable the conventional lift truck to become a more versatile and efficient materials handling tool. These products enable a lift truck to pull, push, clamp, lift, sideshift and rotate practically any unit load imaginable. If you don't see what you're looking for-contact your nearest sales office.
|
|
|
Cascade's Wine Barrel Handler simplifies the barrel handling process. Designed to work in the "cave" or "narrow aisle" operations, the Wine Barrel Handler allows a lift truck driver to easily grab a barrel from a stack, lower it to the ground or move it to the desired location. A 180-degree swinging fork assembly mounted on a full-width traversing frame allows the driver to pick up a barrel from either the left- or the right-hand side of a narrow aisle. The Wine Barrel Handler can handle most types and sizes of wine barrels. Also included in the fork cradle design are rollers to aide in the manual spinning of the barrel for mixing.
|
|
|
The Double Height Shift System is designed to adjust the height of a standard lift-truck mast. This is especially useful if the existing mast does not comply with the requested height or when a certain under-door-clearance is needed. The cylinders are integrated on each side of the forks meaning minimal lost load thickness and maximum visibility.
|
|
Carriage scale for lift trucks
The RVL weighing carriage plate allows weighing in combination with attachments, like clamps or rotators: the carriage plate scale is mounted between the original carriage plate of the trucks and the attachment, via standard Class 2 or 3 fittings.
The 110 weight indicator is mounted in the cabin of the truck. Signal transfer from carriage plate scale to indicator is by Bluetooth connection.
Since the combination of carriage plate scale and attachment causes a displacement of the center of gravity of the load on the forks, it is advised to recalculate the residual lifting capacity of the truck.
|
|
|
If the fork-lift truck is operating on ground that is not flat, one of the forks can compensate for the difference in height ensuring the safe loading and unloading of goods without damage. The combination of two integrated cylinders, connected on each side of the fork, makes the SHSS a very powerful vertical positioning system.
|
|
Hydraulic fork lift truck weighing system MHW+
The Bruss MHW+ is an oil-based weighing system for fork lift trucks with superior accuracy combined with extreme ease of use. With this instrument you will no longer recieve incorrect values in your warehouse and your people can accuratly inform the transport company about the weight of the goods.
Dangerous heavy loads are spotted directly and can be dealt with accoordingly. Safety First!
The Return on investment is unique in the branche - ask your Material handling dealer for a quote. The MHW+ lowers the forks for 4 seconds and weighs the goods while in motion.
This ensure an accurate measurement of the oil pressure which are converted into kilograms.
With a Bruss MHW+ any weight is the right weight.
Bruss Weighing on Wheels
|
|
Bruss hydraulic weighing system - model MHW
The Bruss MHW system is an oil pressure based weighing system which gives a cost effective way to weigh all your loads on your forks. You lift the load to a designated level and manullly lower the forks to a referance point - the MHW software takes and calculates the right weight and shows it in the display you can also use the system for overload protection - an optional warning buzzer stops the operator from handling the heavy load. With Bruss weighing on wheels you are a weigh ahead !!
|
|
RAVAS supplies a complete range of scales for mounting on forklift trucks. For simple check weighing, where a high accuracy is not required, there is the RCS hydraulic load indication system.
An oil pressure sensor is installed onto the hydraulic circuit of the forklift by means of a T-coupling. The indicator in the cabin translates the measurement into a weight indication of the load on the forks. The RCS has a limited accuracy, with a possible error of maximum 2% of the lifting capacity of the truck. The system is meant for simple check weighing, such as the checking of incoming goods, and for avoiding the overloading of lorries, warehouse racking and the forklift truck itself.
|
|
The RCS-110-PLUS is an accurate hydraulic scale for counterbalanced trucks and reach trucks. On a forklift truck with a capacity of 5,000 lbs the weight is displayed in steps of 5 lbs, with a + 10 lbs tolerance. The RCS-110-PLUS weighs by measuring the pressure in the hydraulic lifting system of the forklift truck, via a temperature compensated sensor on a valve block.
During a controlled descent of the mast the pressure in the hydraulic system is measured repeatedly, the software translates these measurements into an accurate weight indication of the load on the forks.
The RCS-110-PLUS is an excellent tool for weight checks on a forklift truck, for example at goods reception, when determining shipping weights, preventing overloads on freight trucks, stocktaking, stock control etcetera.
|
|
| ... products without technical information |
| |
A complete range for handling parts up to 20 kg :
Gripper:
- angular clamping 40° and 180°
- parallel clamping and long stroke
- compacts
- special
Linear modul
(with intermediate position, rod clamping)
Rotating modul
(with intermediate position)
|
|
LINEAR MANIPULATORS of the series H-T are flat conjugate double cam mechanisms that transform the uniform rotary motion into a two-way linear indexing motion typical of pick and place movements. They are manufactured in three different sizes H65T, H80T, H105T and in two special long traverse versions H80TL and H105TL.
With the standard LINEAR MANIPULATORS it is possible to perform traverses up to 480 (mm) in a longitudinal direction and up to 120 (mm) in a transverse direction, reach a velocity of 60 (cycles/min.) and transport pieces up to 30 (kg).
|
|
The MAN family manipulators, featuring a single cam globoidal and flat combined, can turn uniform rotating motion into an appropriate and ordered series of movements, linear intermittent and rotating intermittent (indexing version) or oscillating intermittent (oscillating version) of the output shaft on which are installed gripper device.
The manipulators are characterised by: accuracy, speed and smoothness of the movements, low vibration, silent operation, simple construction, compactedness, oil-bath lubrication of internal components, easy installation and ample diversification of the output shaft movement cycles.
These features grant reliability and flexibility of use in applications that include machine loading-unloading, handling in assembly operations and transfer to conveyor belts.
They are available in five frame size: MAN10-20-30-40-50 with 45-65-85-110-165 (mm) max. linear stroke and angular rotation up to 180°.
|
|
Cam mecanism working in oil bath.
Combines rotation and lift movements. For repetitive process.Maintenance free system.
|
|
- Compact cast aluminum alloy housing
- Fast, accurate and repeatable
- Double extended cam-shaft
- CNC hardened cam-profiles
- Indexing or oscillating custom cam-motions
- Oil bath lubrication
- Can be fitted with reducer and drive
|
|
Lift and Rotate Units
All units are customized based on the requirements of each application. With the combination options of cylinder, disk cam, disc groove, globoidal, pneumatics and servo technology results in a large variety of pick and place solutions.
|
|
|
Koike Aronson / Ransome manufactures a complete line of Head and Tail Stock welding positioners ranging from 600 to 240,000 pounds. Special engineered positioners are always available.
|
|
Linear Modules
- SM type
Diameter mm Strokes in mm
16 30 - 60 - 90
20 30 - 60 - 90 - 120 - 150 - 180 - 200
32 50 - 100 - 150 - 200 - 250 - 300 - 350 - 400
40 400 - 600 - 800 - 1000
- SP32 type
- Stroke length can be adjusted on request, up to 10 000 mm
- For assembly within a frame, the SP32s can be delivered with a length of aluminium profile, according to your needs. The stroke length is adjusted on request.
- Frequent intermediate stops are possible, with centre-to-centre distances of only a few millimetres.
|
|
Rotating modules
- DM type
Diameter (mm) Rotation
12 From 0° to185°
20 From 0° to 365°
25 From 0° to185°
32 From 0° to 185°
63 From 0° to 185°
- DMZ type
Modules with intermediate stops
- Flange version with output shaft
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
