|
|
"Oil / Air Cooler Series BLK
Maintenance friendly design
Compact dimensions
Low noise emissions
Broad performance range
Rugged cooling matrix
Comprehensive accessories" |
|
Oil/air heat exchangers
type LKI
Low noise level
High performance
Low cost
Product description
With this new generation of Universal Hydraulik LKI oil-coolers, the manufacturers have succeeded in reducing the noise level. These coolers are ideally suited for stationary installations - for the cooling of hydraulic or lubricating oils. The range has been extended to include slow-running ventilators, and the housings have been optimised, in order to produce the very low noise level. In order to make the cooler range as comprehensive as possible, the smaller models are also available as single or dual versions, thus covering oil-cooling requirements for both low and high oil throughflow volumes.
Product features
Testing pressure: 26 bar static according to DIN 50104
Operating pressure: 16 bar
(min. 2 Mill. Cycles from 0-16 bar at 2 Hz and 60 °C)
Compact oil-cooler
High operating pressure
High cooling performance
Low pressure loss
Max. operating pressure: 120 °C
High flexibility
2" SAE flange from LKI 700 upward
Also for use with water/glycol
Variable motor; Hydro / 12/24V |
|
AIR-OIL HEAT EXCHANGERS -SERIES AP WITH HYDRAULIC MOTOR :
This type of exchanger has been designed for use on movable machines where battery feed is insufficient or when exchangers with direct current supply are inadequate to produce high thermic yields. The radiative unit is of aluminium because this material is a very good conductor; providing high thermic yields and relatively compact over-all dimensions. Thanks to the particular construction of the radiative unit the exchangers of the series APL cope well with water hammer conditions which, at peak values, must not exceed the minimum allowable dynamic pressure of 20 bar. The maximum allowable static pressure is of 35 bar. |
|
Oil/air heat exchangers
type LKI-HYD
Low noise level
High performance
Low cost
With this new generation of Universal Hydraulik LKI oil-coolers, the manufacturers have succeeded in reducing the noise level. These coolers are ideally suited for mobile installations - for the cooling of hydraulic or lubricating oils. |
|
Oil/Air Heat Exchangers
Very low noise level combined with low costs in the model ranges
- LKI
- LKIHYD
- LKM
Up to 26 bar oil pressure, cooling capacity from 1.5 to 150 kW, respectively from 20 to 700l/min, oil flow. Optionally with bypass valve for pressure peaks. Various electric motors available. |
|
Setrab Oilcoolers
Setrab´s cooler program is designed for flexibility and performance. This means that our product range achieves superior applicability for our customers, and we can devise the best possible solution to suit the conditions dictated by the customer´s application. We can therefore offer our customers the right product for every occasion. Quality has top priority for Setrab. For us it is natural that quality is the guiding star when it comes to service and design, as well as production and distribution, to achieve the result the customer expects. We are working towards the highest quality on all levels within the organisation and the continuous development of our quality assurance system is a process that engages all of our employees.
Setrab's STD, SLM and CP air cooled oil coolers |
|
Long and secure functioning Setrab STD Oil Coolers are used in applications with low to medium-pressure systems or in circulation systems where the oil cooler is an important component for achieving long and secure functioning. For example, in hydraulic systems, engines, transmissions, transformers, fuel coolers, etc.
Technical specifications
- Maximum working pressure is 10 bar. Approved testing at a dynamic working pressure of 0-10 bar, 200,000 pulsation in load, 2 Hz.
- Corrosion protection: Nocolok brazing process and epoxy-coating.
- Connections: BSP |
|
SELF-CONTAINED COOLING UNITS:
The RAS cooling units were engineered and manufactured to substitute the former GAR and OCS series with an uncomplicated and compact product. The units are made up of an aluminium air-oil exchanger and a single electric motor which operates both the oil circulation gear pump and the cooling fan. |
|
| ... products without technical information |
| |
| Vortex CoolersTM from ITW Vortec keep electrical cabinets and control panels cool, clean and protected. An affordable, maintenance-free alternative to air conditioners, the easy-to-install Coolers have no moving parts to wear out. Vortex Coolers incorporate vortex tube technology that uses filtered compressed air to produce a refrigerated air stream distributed throughout the enclosure. Unlike fans that pull in hot, dirty air, the enclosure Coolers maintain a light positive pressure inside the cabinet to effectively seal out the surrounding contamination, heat and humidity that can wreak havoc on sensitive electronic controls. Refrigerated air produced by the vortex tube enters the cabinet while hot air is expelled through a relief valve. Models are available to deliver up to 5000 BTUH of refrigeration. The UL-listed enclosure cooler systems are thermostatically controlled and are available in NEMA 12, 4 and 4X rated models. |
|
Cabinet Coolers - Frigid-X™ series for electronic control panels provide a low cost method of both purging and cooling electrical and electronic control panels by using a stainless steel vortex tube to create cold air from ordinary compressed air.
Cabinet Coolers - Frigid-X™ series are compact and can be installed in minutes through a standard electrical knockout. There are virtually no moving parts.
Cabinet Coolers - Frigid-X™ series are ideal for all NEMA 12 and NEMA 4 rated panels.
Advantages:
- Low in cost
- Compact
- No CFC's
- Fast installation
- Stabilize enclosure temperature and humidity
- Virtually maintenance free (No Moving Parts)
- Mounts in a standard electrical knockout
- Stops heat damage and nuisance tripping
- Eliminates fans and filters
- Prevents dirt contamination by keeping enclosure at positive pressure
- Units applicable to all environments including high temperature to 200ºF |
|
Adjustable Spot Cooler - Frigid-X™ is a low cost and maintenance free Adjustable Spot Cooler system which utilizes a vortex tube to produce cold air at one end.
Adjustable Spot Cooler - Frigid-X™ temperature can be adjusted using a knob at the hot end to set the temperature precisely to your requirements. Temperatures range from approximately minus 30ºF to room temperature and can be easily set with a thermometer.
Adjustable Spot Cooler - Frigid-X™ comes with three brass generators for flow rate adjustment - 15 SCFM (425 SLPM), 25 SCFM (708 SLPM) and 30 SCFM ( 850 SLPM) providing refrigeration up to 2100 BTU/hr (615 Watts).
Features:
- No moving parts or electricity
- Compact and lightweight
- Low cost
- Maintenance free
- Instant cold air
- Quiet
- Magnetic base
- Interchangeable generators |
|
| ... products without technical information |
| |
• Blower and air knife systems custom designed to cool conveyorized products down to ambient temperatures
• Let us know the starting and ending temperatures and throughput rates
• Eliminate expensive compressed air and reduce energy usage by 75%
• Products are CE Registered with IEC Motors
• Sonic is an ISO 9001:2000 Registered company
• Most Blower/Motor assemblies shipped in 5 days from receipt of order |
|
• Blower and air knife systems custom designed to cool conveyorized products down to ambient temperatures
• Let us know the starting and ending temperatures and throughput rates
• Eliminate expensive compressed air and reduce energy usage by 75%
• Products are CE Registered with IEC Motors
• Sonic is an ISO 9001:2000 Registered company
• Most Blower/Motor assemblies shipped in 5 days from receipt of order |
|
|
|
see the results for the following category
