|
|
Off line oil / air blast cooler BNK series
Integrated circulation pump
Low noise emissions
Easy to maintain
By-pass also available
High performance off-line coolers with compact dimensions, motor with two spindles for pump and fan. Matrix easy to dismantle.
|
|
Oil/air heat exchangers
type LKI
Low noise level
High performance
Low cost
Product description
With this new generation of Universal Hydraulik LKI oil-coolers, the manufacturers have succeeded in reducing the noise level. These coolers are ideally suited for stationary installations - for the cooling of hydraulic or lubricating oils. The range has been extended to include slow-running ventilators, and the housings have been optimised, in order to produce the very low noise level. In order to make the cooler range as comprehensive as possible, the smaller models are also available as single or dual versions, thus covering oil-cooling requirements for both low and high oil throughflow volumes.
Product features
Testing pressure: 26 bar static according to DIN 50104
Operating pressure: 16 bar
(min. 2 Mill. Cycles from 0-16 bar at 2 Hz and 60 °C)
Compact oil-cooler
High operating pressure
High cooling performance
Low pressure loss
Max. operating pressure: 120 °C
High flexibility
2" SAE flange from LKI 700 upward
Also for use with water/glycol
Variable motor; Hydro / 12/24V
|
|
AIR-OIL HEAT EXCHANGERS -SERIES AP WITH HYDRAULIC MOTOR :
This type of exchanger has been designed for use on movable machines where battery feed is insufficient or when exchangers with direct current supply are inadequate to produce high thermic yields. The radiative unit is of aluminium because this material is a very good conductor; providing high thermic yields and relatively compact over-all dimensions. Thanks to the particular construction of the radiative unit the exchangers of the series APL cope well with water hammer conditions which, at peak values, must not exceed the minimum allowable dynamic pressure of 20 bar. The maximum allowable static pressure is of 35 bar.
|
|
Oil/air heat exchangers
type LKI-HYD
Low noise level
High performance
Low cost
With this new generation of Universal Hydraulik LKI oil-coolers, the manufacturers have succeeded in reducing the noise level. These coolers are ideally suited for mobile installations - for the cooling of hydraulic or lubricating oils.
|
|
Oil/Air Heat Exchangers
Very low noise level combined with low costs in the model ranges
- LKI
- LKIHYD
- LKM
Up to 26 bar oil pressure, cooling capacity from 1.5 to 150 kW, respectively from 20 to 700l/min, oil flow. Optionally with bypass valve for pressure peaks. Various electric motors available.
|
|
ASA 0177
- Working pressure (static): 26 bar (370 PSI)
- Radiator material: Aluminium
|
|
Setrab Oilcoolers
Setrab´s cooler program is designed for flexibility and performance. This means that our product range achieves superior applicability for our customers, and we can devise the best possible solution to suit the conditions dictated by the customer´s application. We can therefore offer our customers the right product for every occasion. Quality has top priority for Setrab. For us it is natural that quality is the guiding star when it comes to service and design, as well as production and distribution, to achieve the result the customer expects. We are working towards the highest quality on all levels within the organisation and the continuous development of our quality assurance system is a process that engages all of our employees.
Setrab's STD, SLM and CP air cooled oil coolers
|
|
TT 01 :
- Pression de service (statique): 26 bar
- Matière de l'élément refroidisseur: Aluminium
|
|
Long and secure functioning Setrab STD Oil Coolers are used in applications with low to medium-pressure systems or in circulation systems where the oil cooler is an important component for achieving long and secure functioning. For example, in hydraulic systems, engines, transmissions, transformers, fuel coolers, etc.
Technical specifications
- Maximum working pressure is 10 bar. Approved testing at a dynamic working pressure of 0-10 bar, 200,000 pulsation in load, 2 Hz.
- Corrosion protection: Nocolok brazing process and epoxy-coating.
- Connections: BSP
|
|
SELF-CONTAINED COOLING UNITS:
The RAS cooling units were engineered and manufactured to substitute the former GAR and OCS series with an uncomplicated and compact product. The units are made up of an aluminium air-oil exchanger and a single electric motor which operates both the oil circulation gear pump and the cooling fan.
|
|
| ... products without technical information |
| |
Off line oil / air blast cooler BNK series
Integrated circulation pump
Low noise emissions
Easy to maintain
By-pass also available
High performance off-line coolers with compact dimensions, motor with two spindles for pump and fan. Matrix easy to dismantle.
|
|
Oil/air heat exchangers
type LKI
Low noise level
High performance
Low cost
Product description
With this new generation of Universal Hydraulik LKI oil-coolers, the manufacturers have succeeded in reducing the noise level. These coolers are ideally suited for stationary installations - for the cooling of hydraulic or lubricating oils. The range has been extended to include slow-running ventilators, and the housings have been optimised, in order to produce the very low noise level. In order to make the cooler range as comprehensive as possible, the smaller models are also available as single or dual versions, thus covering oil-cooling requirements for both low and high oil throughflow volumes.
Product features
Testing pressure: 26 bar static according to DIN 50104
Operating pressure: 16 bar
(min. 2 Mill. Cycles from 0-16 bar at 2 Hz and 60 °C)
Compact oil-cooler
High operating pressure
High cooling performance
Low pressure loss
Max. operating pressure: 120 °C
High flexibility
2" SAE flange from LKI 700 upward
Also for use with water/glycol
Variable motor; Hydro / 12/24V
|
|
AIR-OIL HEAT EXCHANGERS -SERIES AP WITH HYDRAULIC MOTOR :
This type of exchanger has been designed for use on movable machines where battery feed is insufficient or when exchangers with direct current supply are inadequate to produce high thermic yields. The radiative unit is of aluminium because this material is a very good conductor; providing high thermic yields and relatively compact over-all dimensions. Thanks to the particular construction of the radiative unit the exchangers of the series APL cope well with water hammer conditions which, at peak values, must not exceed the minimum allowable dynamic pressure of 20 bar. The maximum allowable static pressure is of 35 bar.
|
|
Oil/air heat exchangers
type LKI-HYD
Low noise level
High performance
Low cost
With this new generation of Universal Hydraulik LKI oil-coolers, the manufacturers have succeeded in reducing the noise level. These coolers are ideally suited for mobile installations - for the cooling of hydraulic or lubricating oils.
|
|
Oil/Air Heat Exchangers
Very low noise level combined with low costs in the model ranges
- LKI
- LKIHYD
- LKM
Up to 26 bar oil pressure, cooling capacity from 1.5 to 150 kW, respectively from 20 to 700l/min, oil flow. Optionally with bypass valve for pressure peaks. Various electric motors available.
|
|
ASA 0177
- Working pressure (static): 26 bar (370 PSI)
- Radiator material: Aluminium
|
|
Setrab Oilcoolers
Setrab´s cooler program is designed for flexibility and performance. This means that our product range achieves superior applicability for our customers, and we can devise the best possible solution to suit the conditions dictated by the customer´s application. We can therefore offer our customers the right product for every occasion. Quality has top priority for Setrab. For us it is natural that quality is the guiding star when it comes to service and design, as well as production and distribution, to achieve the result the customer expects. We are working towards the highest quality on all levels within the organisation and the continuous development of our quality assurance system is a process that engages all of our employees.
Setrab's STD, SLM and CP air cooled oil coolers
|
|
TT 01 :
- Pression de service (statique): 26 bar
- Matière de l'élément refroidisseur: Aluminium
|
|
Long and secure functioning Setrab STD Oil Coolers are used in applications with low to medium-pressure systems or in circulation systems where the oil cooler is an important component for achieving long and secure functioning. For example, in hydraulic systems, engines, transmissions, transformers, fuel coolers, etc.
Technical specifications
- Maximum working pressure is 10 bar. Approved testing at a dynamic working pressure of 0-10 bar, 200,000 pulsation in load, 2 Hz.
- Corrosion protection: Nocolok brazing process and epoxy-coating.
- Connections: BSP
|
|
SELF-CONTAINED COOLING UNITS:
The RAS cooling units were engineered and manufactured to substitute the former GAR and OCS series with an uncomplicated and compact product. The units are made up of an aluminium air-oil exchanger and a single electric motor which operates both the oil circulation gear pump and the cooling fan.
|
|
| ... products without technical information |
| |
APEX high-perfprmance water coolers are freestanding and compact. Thy are designed and installed to control specialist processes ( electro-spindles, linear motors, laser, electron guns, vacuum pumps, etc ).
Special coolers have been developed for coolant fluids (emulsion and cutting oil).
RLA RLE and RLH range : 6-175 KW cooling power.
|
|
|
Our products are intended to the manufacturers of machine tools and not to the end users.
|
|
|
|
see the results for the following category