Adherent greases

P. 4
ttvvww b function b once hardened the bonded coating forms thin dry firmly adhering lubricant layer which separates the friction components contact thus reducing friction wear considerably the service life bonded coating layer is limited depends diffe rent product characteristics the most important

P. 3
wear this layer is dry adheres firmly to the sur face does not drip off this rules out the possibility contaminating the environment as the case oil grease lubrication bonded coatings ensure dry clean lubrication improve runningin behavior also connection oil grease lubrication protect against wear

P. 13
kluber lubrication b technical questionnaire bonded coatings b sender company kluber lubrication munchen kg geisenhausenerstrabe 7 po box street b d81379 munchen b city postzip code phone number person to contact please make sketch your specifie application technical details please use reverse side

P. 15
publisher copyright kluber lubrication munchen kg copyright kluber lubrication munchen kg reprints total part are permitted if source is indicated voucher copy is forwarded b994012002 edition 0611 replaces edition 0308 the data this technical brochure is based our general experience knowledge

P. 10
i ir j b special applications b b component application b b kluber bonded coating b b advantage b b threaded spindles b 40 to 230 c b fluoropan 340 np b b lifetime lubrication b plain bearings b 40 to 120 c b klubertop tg 05 n b improves runnningin wear protection b belt tensioners b 40 to 120 c b

P. 2
excepted.) Cutting condition Work: Non-step deep hole (L/D=20) Drill: 5mm dia long drill with oil holes Chip High-speed mist Oil mist ejecting nozzle Dry fog smaller than 2 micrometers can hardly adhere to the surface. Making lubricant adhere to the surface of workpiece and tool by spraying

P. 1
ting lubricant is nebulized with compressed air. Prevent environmental pollution by minimized use of cutting oil. Minimum quantity lubrication helps to restrain contamination such as oil leak in the plant. What's semi-dry machining? Eco-friendly Cost down Cleanliness Simultaneous lubrication of cut

P. 14
systems in open drives, an automatic lubrication supply should be prefered. Exceptions are possible, in the case of very small modules, slow speed <1m/s and little proceeding movements; one-time manual lubrication is adequate here. Therefore, we offer an adhering grease - WMH F01 - as well

P. 19
C 18 Schmierung von Kettenantrieben Lubrication of Chain Drives Das PU-Schmierkettenrad besteht aus einem Führungskettenrad aus verschleißfestem Kunststoff und offenzelligen PU-Schaumstoffelementen. Die Zufuhr des Schmierstoffes zu den Schaumstoffelementen erfolgt über eine Hohlachse. Der

P. 24
Förderfähigkeit in Nachschmiereinrichtungen Temperatureinsatzbereich -20°C bis +120°C grease WMH F03 - short-fibred and homogeneous lithium-saponified universal grease with one mineral oil. It can be used for roller and slide bearing lubrication and is appropriate for medium and high load applications

P. 12
C 11 Schmierung von Kugelgewindetrieben Lubrication of Ballscrews FlexxPump ist eine äußerst kompakte Schmierpumpe - ideal zur kontinuierlichen Schmierung von Kugelgewindetrieben. Die FlexxPump ist in 5 Basis-Ausführungen erhältlich, die jeweils bis zu max. 2 bzw. 4 Auslässe bereitstellen und

P. 18
assembly - described by an ordering example: execution of the system in module 2 - pinion with helical teeth (left hand) - mounting axe: straight - tube connector: straight; thread 1/8´´ - suitable hose, pre-filled with grease WMH F01 Nachschmiereinrichtung FlexxPump relubrication unit Flexx

P. 34
failure cleaning also helps to exclude problems related to the incompatibility the anticorrosion agent lubricant finally the lubricant can only adhere properly to the bearing surface if it is free from foreign contamination thorough cleaning is therefore an indispensable precondition achieving the best

P. 2
b e b b r b speciality lubricants from kluber lubrication always good choice lubricants rolling bearings from kluber lubrication selecting the right lubricating grease grease application rolling bearings special lubricating greases cleaning rolling bearings corrosion protection rolling bearings

P. 10
grease application rolling bearings around 90 all rolling bearings are lubricated grease grease lubrication poses far less sealing problems than oil lubrication allows much simpler machine designs further benefit today s highspeed grease formulations are operational speed factors up to 2 million n

P. 25
the darker areas are the target if lifetime rolling bearing lubrication is required applications speed factors n dm 1 million more the lubricating grease s service life is determined primarily high peripheral speeds the resulting forces the temperature which develops such highspeed applications

P. 38
changeover lubricating greases used grease removal relubrication bearings new grease having made the decision to use new grease rolling bearing the old grease should be removed completely from the rolling bearings prior to applying the new grease alternatively it may be possible certain cases to

P. 10
In most applications with bearings in the BTW series, grease with a mineral base oil and lithium thickener is suitable. These greases, which adhere well to the bearing surfaces, can accommodate operating temperatures ranging from ?30 to +100 °C. 1,1 1,0 0,9 0,8 0,7 0,6 0,5 0,4 0,3 0,2 0,1 0 0 0,1 0

P. 11
The initial grease fill can be estimated by G = K Gref where G = initial grease fill [cm3] K = a calculation factor dependent on the speed factor A (? diagram 1) Gref = reference grease quantity (? table 1) [cm3] Running-in of grease lubricated bearings A grease lubricated super

P. 12
Oil lubrication Where speeds are constantly very high (generally, speed factor A > 600 000 mm/min), bearings in the BTW series should be lubricated with oil, as the service life of grease is too short under these conditions and oil provides the added benefit of cooling. High quality

P. 16
as guideline values. They are valid for bearings with standard preload that are fitted on a shaft seat machined to h4 tolerance class under light load (P 0,05 C). In addition, good heat dissipation from the bearing arrangement is a prerequisite. The values provided for oil lubrication apply to the

P. 28
publication High-precision bearings (Publication No. 6002). Printed in Sweden on environmentally friendly paper. Certain image(s) used under license from Shutterstock.com Bearings Seals and units Lubrication systems Mechatronics Services The Power of Knowledge Engineering Drawing on five areas