|
|
| ... products without technical information |
| |
Screw-clamp feed-through manufacturers of terminal blocks, CBC Series, polyamide insulating body, UL94V-0 flame behaviour, reduced overall dimension, cross-connections (PTC) by ?Easy bridge? patented system, with no need of additional protection.
To be mounted onto TH35 - 7.5; TH35 ? 15 type rail, according to IEC 60715. |
|
Differents kinds and possibles uses:
- Single Level
- Multiple Connection
- Double Level
- Triple Level
- Distribution Blocks
- Micro
- Modular Panel Mount
- Single Level Industrial fuse
- Double Level Fuse
- Disconnect & Test
- Manufacturers of thermocouple
- Earthing
- Neutral/Earth Clamp specifications
- Corrosive/Explosive Env.
|
|
Optimum contact ensured through the patented and renowned clamping yoke system which is based on the classical increase of force of the screw. Requring only small effort, the screw thread produces high contact power.
A high contact force is only effective when continuously excerted on the conductor. The Weidmüller clamping yoke system works as follows: When the clamping screw is tightened, the resultant force causes the upper thread overlap to spring open, thus causing a locking action to be exerted on the screw. Movement of the connected conductor is compensated by the elastic behaviour of the clamping yoke.
Result:
The connection is vibration-resistant and makes retightening of the clamping screw unnecessary. |
|
Pressfit Power Professional taps with Screw Mount and Angled Slip-on Terminals
10 pin
Pressfit Power Taps with Screw Mount Terminal
6 pin
10 pin
Solder Power Taps with Screw Mount Terminal
6 pin
10 pin
|
|
The screw connectors supplier are intended for stranded and solid aluminium and copper cables, carrying low and medium voltages of up to 36 kV. The range covers cross-sectional areas of 6-630 mm² for round cable and 25-300 mm² for sector cable.
Connection to the conductors is achieved by tightening the screws in the through connector or terminal to a predetermined torque. Tightening takes place into a partially threaded nut. The tightening torque is correct when the screw breaks at its notch. It does this thanks to an innovative double-ended shear-off screw, as shown in the illustration |
|
Flexible lacing with self tapping screws:
- No drilling preparation, no template
- The screws professional drill themselves through the belt
- Good compatibility with scrapers
- Very long life time.
- Installation regardless of weather conditions
- Usable for an emergency splice of a steel cord belt
Material:
Reinforced rubber corresponding to conveyor manufacturers quality: wear resistant, heat resistant, oil resistant, fire resistant, white FDA, textile on the bottom and non magnetic.
Installation:
By using an electric screw driver, a hand brace or a pneumatic screw driver.
Packaging:
In length up to 3 m in one piece or on roll up to 25 m long. |
|
Professional fasteners with self tap screws:
- No drilling preparation, no template
- The screws professional drill themselves trough the professional belt
- Clamping effect of the plates against the belt
Material:
Fastener made of galvanized steel or non magnetic stainless steel.
Installation:
By using an electric screw driver or a pneumatic screw driver or a hand brace (for underground mines).
Packaging:
In pieces made for the requested belt width up to 3,000 mm in one piece.
The screws are provided in a plastic professional bag. |
|
Our range includes:
- Euro Bolts suppliers
- Ref 70
- Hawk Fang Bolts
- Easifit
- Large Oval Washers,... |
|
| Find all bolts necessary to use with industrial elevator bucket : screw, curved washers, flat washers, nuts, large oval washers underlt the head of the TF bolt, space washer. |
|
| Ball transfer units provide instant directional change and are manufactured to meet the highest standards of performance in load transfer applications |
|
| ... products without technical information |
| |
The main features:
- modular conception of screws and barrels
- easy and low-cost adaptation of the system
configuratio to the individual processing task
- throughputs up to 60 kg/h
- applications from material development up to small-scale production of profiles |
|
| ... products without technical information |
| |
This series of gear reducers with attached or integrated thrust industrial bearing can be supplied in a helical or bevel winding gear arrangement. Quiet operation and strong design are key features. Horizontal or vertical mounting position, splash lubrication and cooling coil or injection lubrication are possible options. The modular design of the POSIREX is based on the POSIRED 2 range, plus a selection of available thrust-bearing parts.
Technical Data:
Torque (T2 nominal): 3,000 up to 800,000 Nm
Transmission Ratio: 4 up to 160 iN
Axial force: F = 50 up to 2,000 kN
|
|
Double shaft extruder suppliers professional gears have been built by PIV Drives since 1984 for a variety of applications in the plastics and food industries. This product is in operation around the world to the complete satisfaction of our customer base. The gearing is case hardened and ground with a profile correction for optimal load-bearing performance and noise reduction. An extremely quiet gear-train is achieved through a high contact ratio. The axial forces which occur during the extrusion process are safely absorbed through a system of tandem bearings manufacturer and self-aligning roller thrust bearings.
Technical Data:
Screw centre distance: a = 15 up to 200 mm
Input speed: up to 1,800 rpm
Torque factor: df = 35 Nm/cm3
Power: up to 5,500 kW
|
|
Our product line consists of proven technology including PneumaticScaleAngelus' Pneumacapper and Consolidated Capem Professional cappers. We also offer a wide variety of sorters to accommodate any size and shape.
-Proven technology from PneumaticScaleAngelus including Consolidated's Capem Cappers
-Reliable, minimal-maintenance, highly versatile capping solutions from the industry leader in packaging automation
-Widest range of cap and containers with maximum speeds of 750 CPM
-Superior customer service and technical support |
|
| Single-head capping line with magnetic professional clutch head and Pick & Place device suitable to apply special plastic pre-threaded screw caps on special glass, PET and PVC bottles. |
|
Extrusion splicer is carried out in wide variety of areas and is becoming evermore demanding. Leister offers the right tool for all plastics applications in process equipment manufacture and civil engineering. The specialist obtains everything with us from a single source: Devices from 0.3 to 6.0 kilo per hour. Convince yourself.
• Ideal for tight spaces
• 360° rotatable welding professional shoe
• Easiest possible handling |
|
New hand-manufacturer of extruders are equipped with brushless self-blowers lasting more than 40,000 hrs work, self-diagnose system, working-hour industrial counter, double temperature controller with 2 C accuracy.
The extruders are ready to work within 3.5 min and they cool down automatically within only 2 min., ensuring much longer life to the heating elements to further reduce the equipment maintenance. |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
1 products in 
| |
