|
|
| Camfil Farr Power Systems protect people, machines and the environment. We design and manufacture air cleaning, noise reducing equipment and dampers for the industry. We have been in the business for more than 40 years,and thousands of our installations can be found all over the world - assuring reliable, efficient and cost-effective day-to-day operation of turbomachinery. |
|
| ... products without technical information |
| |
PRECILEC RADIO-ENERGIE alternators WIND PMG equip with the wind turbine of small power. Our Permanent Magnet Generator charge the battery to ensure the power supply of the isolated places, off-line to an electrical grid local.
ADVANTAGES OF OUR DESIGN
Our design is reliable, simple and compact
Our know-how is the integration of rare earths magnets. They are very stable, with high coercive magnetic field and high specific energy
Stability of the voltage in process of time
No voltage loss even after a short-circuit
Our design allows an optimal output according to the required configuration
Dismantling without voltage loss: no irreversible demagnetisation
Large number of solutions: pole number, size for the machines which allow to consider all your demanding space requirements
Mechanical interface is optimized
Highest power-to-weight ratio
In direct drive without speed multiplier or gear
No maintenance needed for machine without bearings
Maintenance limited to bearings only for machine with bearings
ELECTRICAL CHARACTERISTICS
Maximum economical values
Three phase or Single phase
Voltage U eff. max 500 V (between phases)
Power P mech. max 20 kW
Frequency F max 400 Hz
Power Factor: cos phi 0 < cos phi < 1
Distortion max 5% (No-load and Full load)
Rated speed max 3000 rpm
MECHANICAL CHARACTERISTICS
Cooling: IC 00, IC 01, IC 0041 or IC 0141
Protection: IP 00, IP 23, IP 44 or IP 55
Insulation class F
Temperature rise class F or B: 100 K or 80 K
Ambient temperature: 40°C or others
According to the required speeds and mounting modes (Rotor/Stator): binding of the rotors (magnets): either metallic or carbon fibre |
|
YTRON-Y ByPass system - Incorporation of free flowing powders without a tendency to stick of form lumps such as Silica, Active Carbon, HPMC, Cocoa, Flour, Carbon Black, can be drawn in below liquid level by the negative pressure created by the rotor/stator system. The venturi shaped stator and the negative pressure created by the flow it affects, draws the powder in, dispersing it instantly and homogeneously into the liquid. The formation of lumps is eliminated.
Certain powders with a low bulk density can be sucked directly and dust-free from a bag or other container.
Liquids such as S.L.E.S., concentrates, additives, and pastes can as well be pumped in via the YTRON-Y ByPass tube, directly into the turbulent zone in the YTRON-Y mixing head. They are then quickly and instantly diluted or dispersed into the batch. The mixing efficiency of YTRON-Y remains unchanged.
|
|
YTRON-Y rapidly and homogeneously mixes, without aeration, liquids and moderately viscous products. The standard production range includes five different group sizes, with power ranging from 0,25 kW to 55 kW. This corresponds to vessel sizes of up to several million liters volume.
By selection of the suitable mixing rotor, either gentle mixing or intensive shear is applied to the product, but in all cases the mixing action will be very efficient.
The robust construction means that it does not require bearings or seals in the immersed part and therefore involves no hygienic risc. Hygienic execution with surfaces up to mirror polish are available. The use under ATEX conditions is no problem, providing is has been respected in the engineering phase of the project.
Typical use is in the Food, the Chemical , Pharmaceutical and Construction Industries.
Additional services are the supply of hoists (wall mounted, floor mounted or mobile) with manual, electrical or pneumatic drive.
Optional: Support for fork lift or tackle block.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
TECHNICAL CHARACTERISTICS :
· Power : 40 to 3000W
. Stall Torque : 2 to 630 N.m
· Air pressure : 6 bars
· Rotation : right, left and reversible
· Angle head available from 400 to 1800W
Design team available you specific designed to order products. |
|
Turbine Sentry - System Overview
An overview of the complete system and how this system is of benefit to gas turbine operators.
A typical system comprises three parts:
Blade Sentry - Measurement Pyrometer
The non-contact thermometer is mounted through the gas turbine casing and measures the temperatures of individual rotor blades.
Rotor Sentry - Data Acquisition System
The DAS logs individual blade temperature readings taken by the measurement pyrometers, samples and processes the data for use by the data analysis software, Data Sentry.
Data Sentry - Data Analysis Software
This powerful pc-based software utility has all the tools and functions necessary to obtain a complete picture of how efficiently the gas turbine is running, as well as identifying potential problems at an early stage.
|
|
| CENTRALIGN® is a laser alignment system that uses the inherent high precision of the laser beam as its reference, as opposed to the conventional methods that utilize dummy shafts and piano wires, for the precise adjustment of turbine internal parts. It offers accurate and independent alignment records. CENTRALIGN® improves productivity by shortening the outage time of turbines. |
|
| One of Allen Gears key assets is the ability to use our extensive knowledge of gear technology and application requirements to provide solutions that achieve the optimum transmission solution for the desired drivers. We achieve this through combining the transmission technologies of parallel shaft, epicyclic and bevel gearing to produce combination gearboxes that best meet the installation and operation requirements. |
|
Size: K20 ITH6
Zeropoint Quickclamping cylinders with turbine for automatised solutions with:
• Turbine function for complete cleaning of support surfaces without „shady side“
• Central locking against pollution particles
• Hydraulic or pneumatic locking sensors
• Control of contact by air blocked
• Hydraulic pre-expulsion for palletizing solutions with also possibility to swing completely free during the catchment
• No damage of media-coupling |
|
Grade: N42
size: 2" x 1" x 0.5"
coating: Ni-Cu-Ni
Magnetized through the Thickness 0.5"
Applications: wind turbine or other projects
For years, we have been offering the magnets for wind turbines worldwide. we have a team of technicians with rich experience in the R&D of magnets for wind turbines.
Because of the maximum working temperature, magnets using in Wind turbines are series SH, such as grade 42SH, 45SH and so on
The magnets for wind turbines, usually we offer L-T series for wind generators, Compared to the Conventional Formula and the T-series, the correlative temperature coefficient and weight loss are better. it will well prolong the life twice than usual.
For the details about the L-T series or the magnets, please do not hesitate to contact us or view our PDF Catalogues " special magnets for wind turbine" , we are at your services any time.
If you are interested in our factory, please do not hesitate to contact us, we are at your service any time
Contact details:
Steve Chen (Mr.)
Email: tcexport@ndmagnets.com
Tel:86-574-88170908
Mobile:86-15990259284
MSN: toddywell@hotmail.com |
|
... see all the products in the category
Magnets
|
Air Turbine offers a wide range of spindles operating at constant speeds from 25,000rpm to 65,000rpm maintaining constant high speed under variable load with no gears or vanes. Over 40 spindles - easily mounted, maintenance free, requiring no lubrication, provide a finer finish and faster feed rates. No stop block needed with Air Turbine Tools®. Low vibration, super quiet, oil-free spindles.
Announcing the new 275 Series:
Designed with screws through the endcap and an extra-wide body, extra stability results from a two-piece stainless steel housing with integral shank and triple ceramic bearings for precise concentricity of 0.0002" (0.00508mm). The 275JS has extra durability to work with harder materials. Compact and easily installed with a 1" or 25mm straight shank for easy mounting to CNC machines or tool holders. For drilling applications, specify angular contact bearings. Our double turbine X units provide extra power where required. (up to 1.4 HP (1.04 kW)
|
|
Faster Production - spindles operating at constant speeds from 25,000rpm to 90,000rpm up to 1.4HP, maintaining constant high speed under variable load with no gears, vanes, or brushes.
Over 40 spindles - easily mounted, maintenance free, requiring no lubrication, provide a finer finish and faster feed rates.
Patented low vibration, super quiet, oil-free, direct drive spindles for faster production and greater durability. Integrated CAT, BT, HSK, and DIN toolholders available for increased accuracy. |
|
Constant high speed and torque under load, make this series ideal for robotic finishing or milling metals, or cutting plastics, ceramics, composites or wood.The HD Series incorporates heavy-duty bearings within a ridgid stainless steel housing which may be fixture mounted easily.
Units generate up to 1.4 HP with governed constant high speed and no gears or vanes to lubricate or repair. These reliable motors have fewer moving parts and need fewer repairs. Cleaner cutting action, more IPM's. A light and compact solution with low vibration and weight. Oil free and maintenance free operation. |
|
| ... products without technical information |
| |
|
