|
|
High gradient magnetic separators for capturing fine ferrous and paramagnetic particles in liquids and slurries
Main applications include ceramics and minerals processing industries to purify raw materials, such as ceramic bodies, silica and feldspathic sands and to upgrade quality of final product (purer, cleaner and whiter product)
Proven in practice to offer 30% greater separation performance than traditional WHIMS systems.
|
|
TYPICAL APPLICATIONS
EFS
Standard size housings available with 30 (590), 60 (250), 100 (149), and 150 (99) mesh (micron) reusable, stainless steel filter cartridges. Units measure 11.25" long and feature a 1" NPT intake and dual 1" NPT discharge ports (3/4" reducers provided).
FEATURES
Graymills Superflo filters are designed to overcome the typical pressure drop and reduced flow due to clogging that occurs with ordinary filters. A permanent magnet suspended over the intake port traps ferrous particles which find their way into the fluid, and diffuses the flow outward into the filter screen flutes. Filtered material is trapped on the inside of the removable/reusable stainless steel filter cartridge. To clean, just remove the cartridge. All the contaminants come out with it. Self draining. No wasted fluid or messy leftovers to deal with. Stainless steel filter cartridges are available in four different mesh screens. |
|
As pre-cleaners or main cleaners for subordinate applications and magnetisable chips, magnetic filters offer a good and reasonably priced filtration method.
Turbo Separator AG produces magnetic filters with flow rates of 100 - 400l/min.
Depending on the application area, these magnetic filters can also be built up in cascades.
Magnetic filters from Turbo-Separator can be installed as integrated components of a system or built on as accessory products.
Special requirements call for special solutions - we shall implement your wishes, with unconventional solutions if need be! (SE magnets)
|
|
| ... products without technical information |
| |
High gradient magnetic separators for capturing fine ferrous and paramagnetic particles in liquids and slurries
Main applications include ceramics and minerals processing industries to purify raw materials, such as ceramic bodies, silica and feldspathic sands and to upgrade quality of final product (purer, cleaner and whiter product)
Proven in practice to offer 30% greater separation performance than traditional WHIMS systems.
|
|
TYPICAL APPLICATIONS
EFS
Standard size housings available with 30 (590), 60 (250), 100 (149), and 150 (99) mesh (micron) reusable, stainless steel filter cartridges. Units measure 11.25" long and feature a 1" NPT intake and dual 1" NPT discharge ports (3/4" reducers provided).
FEATURES
Graymills Superflo filters are designed to overcome the typical pressure drop and reduced flow due to clogging that occurs with ordinary filters. A permanent magnet suspended over the intake port traps ferrous particles which find their way into the fluid, and diffuses the flow outward into the filter screen flutes. Filtered material is trapped on the inside of the removable/reusable stainless steel filter cartridge. To clean, just remove the cartridge. All the contaminants come out with it. Self draining. No wasted fluid or messy leftovers to deal with. Stainless steel filter cartridges are available in four different mesh screens. |
|
As pre-cleaners or main cleaners for subordinate applications and magnetisable chips, magnetic filters offer a good and reasonably priced filtration method.
Turbo Separator AG produces magnetic filters with flow rates of 100 - 400l/min.
Depending on the application area, these magnetic filters can also be built up in cascades.
Magnetic filters from Turbo-Separator can be installed as integrated components of a system or built on as accessory products.
Special requirements call for special solutions - we shall implement your wishes, with unconventional solutions if need be! (SE magnets)
|
|
| ... products without technical information |
| |
Along with the mechanically operated limit switches, magnetic reed switches (magnetically operated) have been constantly gaining increased importance. They can be regarded as a complement to the plunger, roller and turret head operated limit switches and as an important addition to electronic proximity switches.
|
|
| ... products without technical information |
| |
|
Plant and mechanical engineers are responsible for ensuring personal safety. The machine safety products of elobau range from sensors and evaluation units for small machines to bus components for large plants. The personnel of elobau GmbH offers support with the implementation of the latest safety guidelines.
|
|
Safety coded magnetic sensor, SR-SM series
Pizzato Elettrica offers on the market the new safety magnetic sensor SR-SM series.
Safety magnetic sensors are devices studied to monitor protections and guards that, when linked to a safety module, can create a system up to safety category 4, according to EN 954-1. These products are composed by a magnetic field monitoring sensor, which is connected to the machine structure; and by a coded magnetic actuator, which has to be connected to the mobile guards. The sensor is manufactured to be activated only by the correct coded actuator and not through a common magnet.
Pizzato Elettrica safety sensors distinguish themselves by following main features:
• Insensitivity to dirt as totally sealed, making them especially proper to be used in the food-industry sector.
• Wide actuation zone, characteristic appreciated in the use of inaccurate protections or for protections that can change their mechanical characteristics through the time.
• Stainless steel fixing plates to avoid that the sensor could be damaged during the installation.
• Possibility of connection in series more sensors also with mechanical switches.
• Actuation from two different directions.
• Available with cable or M8 integrated connector.
• Actuators with operating distance of 5mm or 8 mm.
The new sensor series complete the wide range of products that Pizzato Elettrica can offer in the machine safety field. For further information visit our web-site www.pizzato.com or ask for special documentation. |
|
The Idemag CPR Non Contact Interlock Switch range offers a compact slimline fitting and provides environmental protection up to 80C. and is suitable for high pressure hosing (IP66/67).
The housing is finished and sealed with a fitted back plate for extra mechanical and environmental durability.
In addition to the high specification enclosure the switch offers a wide 14mm sensing distance, a high tolerance to misalignment and can be actuated rom either the side or front switch face.
They will connect to most popular Safety Monitoring relays to provide up to Cat. 4 EN 954-1. |
|
The Idemag WPR Non Contact Interlock Switch range offers a robust wide fitting and provides environmental protection up to 80C. They are suitable for high pressure hosing (IP66/67) and are resistant to many organic and non organic chemicals.
The housing is finished and sealed with a fitted back plate for extra mechanical and environmental durability.In addition to the high specification enclosure the switch offers a wide 14mm sensing distance, and a high tolerance to guard misalignment.They are designed to fit to medium to large guards.
They offer 2NC high power (up to 2A.) circuits and will connect to most popular Safety Monitoring relays to provide up to Cat. 4 EN 954-1. An auxiliary signalling contact is available. The high power components and de-rating with an internal fuse mean they may be suitable for use in lower risk applications (subject to a risk assessment for the application). |
|
|
The industry's most complete line of contact and non-contact products. GE Security Industrial safety interlock switches are used to detect the opening of guards-including doors, gates and/or removable covers-that prevent access to dangerous parts of a machine, and to help deter tampering with the guards or the internal machine controls. As with all GE Security Industrial 300-BT products, the safety interlock switches are in full compliance with the most current and required standards. These include IMQ, CE, VDE, UL, CSA, IEC, EN and Semi S2 standards.
|
|
Permanent electro-magnetic clamping of moulds on injection mould presses adapted to all sizes and shapes of mould.
STÄUBLI offers a complete range of products serving the PLASTICS INDUSTRY including:
- quick mould clamping,
- quick connection of services using quick-release couplings and multi-couplings,
- automatic ejector hook-up,
suitable for all methods of mould changing: vertical or horizontal loading and existing or new machines.
|
|
Quad-Press: A magnetically clamped mold is subject to neither deformations nor to inner tensions.
The force is distributed uniformly throughout the contact area, instead of only being applied on the external edges of the base-plate, as it happens when traditional clamping methods are used.
The quality of the molded part is constant in time.
Each 80HC square pole generates a constant, predictable and concentrated force of 1000 kg.
This force improves the performances to an unbeatable level, giving a greater available force in a smaller contact area.
Lead time is strongly reduced; now the SMED production is a reality.
Moulds of any size, even bigger than the machine plates are easily clamped with no modification.
Quad-Press is maintenance free, due to it doesn't present any mechanical component inside.
The new IPC system is available on request with the touch-screen device.
IPC follows step-by-step the machine operator during mold change procedure and give in real-time the actual clamping force generated on the mold.
|
|
HotMAG
permanent electro magnetic system for quick clamping of high temperature moulds.
The new permanent electro magnetic system HotMag is the final answer to all the needs to make quick change operations on press machines working with high temperature moulds.
The innovative magnetic circuit, made of special solenoids and high energy permanent magnets, allows to
operate with temperature up to 250° C. (482 ‘F).
The full metallic surface allows the perfect stability and uniformity of clamping all over the contact area
granting high performances in the long run.
Quick: Few seconds only to activate and deactivate the system. Simply pushing a button!
Ergonomic: The operator that can remain always at a distance from the mould. No risk!
Easy and practical: No modification to the machine, no modification to the moulds and no special tools are required.
Time saving: The mould can be preheated outside the machine with a great advantages!
Safe: Only the high strength generated by the permanent magnets will hold the mould at indefinite period of time.
Convenient: The low investment and the high efficiency grants a quick pay back.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category
